Bedienungsanleitung Black Decker SZ360 T1 (Seite 5 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

578039

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

Features

1. Cutting head

2. Lock switch

3. On/off trigger switch

4. Charging socket

5. Charger plug

6. Charger

Warning! Before cleaning, adjustment or replacing the cutting

head. Set the lock switch to OFF (0).

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (fig. B)

The battery needs to be charged before first use and

whenever it fails to produce sufficient power on jobs that

were easily done before. When charging the battery for the

first time, or after prolonged storage, it will only accept an

80% charge. After several charge and discharge cycles, the

battery will attain full capacity. The battery may become

warm while charging; this is normal and does not indicate a

problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

X To charge the battery, insert the charger plug (5) into the

charging socket (4).

X Plug in the charger (6). Switch on at the mains.

X Leave the tool connected to the charger for 12 hours.

The charger may hum and become warm while charging; this

is normal and does not indicate a problem.

Generally, a charging time of 8 hours will enable the tool to

operate at an effective power level for most tasks. However,

further charging for up to 12 hours could significantly

increase the run time, depending on the battery and charging

conditions.

X Before using the tool, unplug the charger and disconnect

the tool from the charger.

Warning! The tool will not operate while it is connected to the

charger.

Switching on and off (fig. C)

X To switch the tool on, push the lock switch (2) into the ON

position (I) and squeeze the trigger switch (3).

X To switch the tool off, release the trigger switch and slide

the lock switch to the OFF position (0).

Cutting

Hold the tool firmly while cutting.

X Switch the tool on and let the blade run freely for a few

seconds before starting the cut.

X Apply only a gentle pressure to the tool while performing

the cut.

Keep hands away from the cutting area and be aware of

materials and surfaces under the cutting area that the blade

may contact.

Do not force the tool. If the tool will not cut, consider the

thickness or hardness of the material, does the tool require

charging, does the cutting head require replacement?

Do not attempt to cut metal or materials that may damage

the cutting head.

Warning! Before cleaning, adjustment or replacing the cutting

head. Set the lock switch to OFF (0).

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the tool,

unplug the charger before cleaning it.

X Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

X Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner. Never let

any liquid get inside the tool and never immerse any part of

the tool into liquid.

Replacing the cutting head.

The cutting head contains no serviceable parts and should be

replaced whenever worn or damaged. Do not attempt to

sharpen the cutting surfaces. Replacement cutting heads are

available from your Black & Decker repair agent.

Fitting and removing the cutting head (fig. A)

To remove the cutting head (1) for cleaning or replacement.

X Separate the scissor blades and set the lock switch to the

OFF (0) position.

X To exchange cutting heads, grasp the scissors as shown in

figure A with fingers at the side of the cutting head and the

hand away from the blades.

X Press in on the sides of the cutting head and pull

straight out.

To attach a cutting head, line it up with the body of the scissors

and push it on until it snaps into place. If the cutting head does

not line up easily, carefully separate the blades from each other

first then re-attach.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker SZ360 T1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker SZ360 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info