Bedienungsanleitung Blaupunkt memphisdj3 canb 84 04 (Seite 6 von 12) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

165708

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Notes on Safety

Instructions for installation and connection

Disconnect the battery ground wire during installation and connection.

When drilling a hole, be sure not to damage any vehicle part (battery,

cable, fuse, etc.).

The positive cable must have a cross-section of at least 2,5 mm

. The unit

is protected by a quick-acting fuse of 10 A. Do not use the positive cable

installed ex factory.

The side panel of the car radio heats up considerably during

operation.

Attention: Pay attention that the cables do not contact with the

housing.

Note:

By means of the support included in the delivery you can mount the set

in cars with a DIN car radio cut-outout of 182 x 53 mm, an installation

depth of 165 mm and an instrument panel thickness around the fixing

clips of 1 - 20 mm, see fig. 1.

For cars with other cut-out dimensions Blaupunkt delivers car-specific

installation kits for common car types for 50/52 mm sets.

Please check the dimensions and, if necessary, use a car-specific

installation kit, e. g. VW Golf II / Jetta II/: 7 608 3824 73.

When using installation sets for units of 52 mm four distance plates, order

number 8 601 055 056, must be used, fig. 1a.

Preparation of car radio installation

Install the car radio into the DIN cut-out provided in your car’s dashboard

ex factory.

Prepare the car radio DIN cut-out (unlock shelf or dummy cover) or cut

out the car radio compartment to 182 x 53 mm.

Grasp behind the car radio cut-out and check how many of the fixing

strips of the car radio support can be bent.

Note:

Try to bend as many fixing strips as possible.

Insert the support into the cut-out and bend the appropriate fixing strips

with a screwdriver, see fig. 1, 2.

Connection

Connection overview .................................................................... fig. 4

Notes on connection ..................................................................... fig. 5

Connection of equalizer and amplifier .......................................... fig. 6

Connection of CD-Player .............................................................. fig. 7

Loudspeaker connection:

4 speakers (4 Ω/20 W).................................................................. fig. 8

Impotant notes!

If these notes are disregarded, there is danger of destroying the

final stages.

Do not connect speaker outputs to ground!

Connection with multiple plug installed ex factory

Do not use the positive cable installed ex

factory.

Connecton with vehicle specific Quick-Fit

Not possible

Connection with QuickOut installed ex factory

If your car is fitted with a QuickOut ex factory (at present Opel), the

QuickOut ex factory has to be removed.

Car radio installation

Insert the car radio from the front into the support and push in until the

stop springs on the sides engage right and left (distinct click to be heard).

Removal of the car radio

Insert the brackets right and left into the provided trimplate holes and

push in until you hear a distinct click (lateral springs are unlocked).

Using both brackets (see fig. 3), pull the unit out.

Note

Locked brackets can only be removed after taking out the unit.

QuickOut (shuttle support)

Use the car radio specific QuickOut support.

Notes on connection, fig. 5

Ground cable

Do not connect the ground cable to the negative pole of the battery.

Route the ground cable to a suitable ground point (car body screw, car

body metal sheet) and shorten it accordingly.

Remove the insulation from the ground cable and attach the forked cable

lug (if necessary, solder it).

Scratch off the paint from the contact area of the ground point and

lubricate it with graphite grease (important for good ground contact).

Screw on the ground cable.

Positive cable (ACC + 12 V) (ignition)

Do not use the positive cable installed in the car.

Route the positive cable (thick red cable of 2.5 mm

) to the battery (do not

route the cable near the cable harnesses). Connect the fuse holder to

protect the positive cable and connect it to the positive pole of the battery

(if necessary, drill a hole into the fire wall and use cable ducts).

Note:

Upon customer request and if the car radio system is operated via the

ignition, the switched positive line, installed ex factory, can be connected

to a relay (Bosch part no. 0 332 014 125).

Permanent plus connection (Battery +12 V)

Connect the permanent plus terminal together with the cable and cable

clamp to a fuse-protected positive line (e.g. clock, warning flasher).

Control cable (Power Antenna +)

When connecting a fully automatic motor antenna, use the cable clamp

to fasten the control cable of the motor antenna to the control cable.

Modifications reserved

Notes de sécurité

Instructions de montage et de branchement

Pendant le montage et le branchement des appareils, il convient de

déconnecter le pôle négatif de la battérie.

Veiller à ce qu’aucun élément de voiture (tel que la battérie, les câbles,

les porte-fusibles) ne soit endommagé par le perçage des trous).

La section du câble positif ne doit pas être inférieure à 2,5 mm

. L’appareil

est protégé par l’intermédiaire d’un fusible à déclenchement rapide 10 A.

Ne pas utiliser le câble positif installé de l’usine.

Le panneau latéral de l’autoradio s’échauffe considérablement

pendant l’opération.

Attention: Alors faire attention qu’aucun câble ne touche le boîtier.

Note:

A l’aide du support inclus dans le jeu de montage vous pouvez monter

le poste dans des voitures qui disposent d’une découpe DIN de 182 x 53

mm, d’une profondeur de 175 mm et d’une épaisseur du tableau de bord

de 5,2 - 6,3 mm autour des éclisses de montage, voir fig. 1.

Blaupunkt livre des jeux de montage spéciaux pour les voitures courantes

avec des découpes différentes pour les appareils 50/52 mm.

Veuillez donc vérifier les mesures de la découpe de votre voiture et, si

+12V

per. +12V

+12V

Blaupunkt memphisdj3 canb 84 04 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info