Bedienungsanleitung Blaupunkt Munchen CD 43 (Seite 5 von 15) (Englisch)

614605

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

München CD 43

4 TREB – for treble control

Press rocker switch –

The display shows a number between

-6 and +6. Use the seek tuning rocker

switch << >> G to adjust treble. Press

the TREB button again to finish the

entry. Approximately 8 seconds after

the last adjustment the display returns

to indication of radio/CD functions.

5 LD button

Loudness – boosts the bass frequen-

cies at low volumes. If the loudness is

switched on, display 9 g lights up.

6 GEO – balance and fader control

Press button –

The display shows “B” (balance) or “F”

(fader) and a number between -9 and

+9. To correct a setting press rocker

switch F or G within 8 seconds.

Use rocker switch << >> G for balance

adjustments (left/right volume).

Use rocker switch

/ F for fader

adjustments (front/rear volume).

The adjustments 3, 4 are finished by

pressing the GEO button. Approximate-

ly 8 seconds after the last adjustment

the display returns to indication of ra-

dio/CD functions.

7 DSC button – Direct Software Control

e.g. for setting the loudness level

Operating instructions

The operating instructions contain infor-

mation on all basic adjustments set via

the DSC function, as the display colour,

the seek tuning sensitivity, the loudness

level, the volume for traffic messages/

audible alarm, and the BEEP (after

actuation of a button).

Radio operation

2 SCAN knob

For briefly sampling the stations to be

received in the selected waveband.

Press knob - the seek tuning function

starts sampling one after another all

stations to be received in the activated

waveband. To continue listening to a

sampled station terminate the SCAN

function by pressing the knob again.

8 lo button - seek tuning sensitivity

Use this button for changing the sensiti-

vity of the seek tuning function.

lo 9 h lights up –

Normal seek tuning sensitivity; the ra-

dio captures powerful nearby stations

only. Stereo programmes are played in

stereo.

dx 9 h lights up –

Highly sensitive seek tuning sensitivity;

the radio also captures weaker stations.

Stereo programmes are played in ste-

reo.

Due to regionally differing reception

conditions, the seek tuning sensitivity

can be individually stored with the DSC

function (

Adjusting the seek tuning

sensitivity).

The lo button can also be used to

switch from stereo to mono and vice

versa.

For this, press the lo button for more

than 2 secs.

In stereo mode display 9 m illumina-

tes.

9 Display indication for

a) Frequency, code

b) ARI zone identification (lights up

when the set is tuned in to a traffic

station)

d) ARI priority for traffic stations

g) LD – loudness level

h) lo, dx (seek tuning sensitivity)

j) FM storage levels (I-III or T)

k) Preset buttons (1-5)

l) Wavebands (U=FM, M=AM, L=LW)

(Stereo)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt Munchen CD 43 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blaupunkt Munchen CD 43

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info