Bedienungsanleitung Blaupunkt vr 2100 velocity (Seite 3 von 16) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

165767

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Velocity Reference Amplifier VR 250, VR 2100

The amplifier is suitable for connecting to car radios with cinch connector.

Use the Blaupunkt ISO-Cinch Adapter for connecting to car radios with

ISO connector.

Possibilities for use and switching:

VR 250 VR 2100

Max Power 2x100 / 1x300 W Fig. 7 2x200 / 1x600 W

4 Ohm Tri - Mode

Max Power 2x150 / 1x400 W Fig. 7 2x300 / 1x 1000 W

2 Ohm

Max Power 2x230 W Fig. 7 2x400 W

1 Ohm

RMS Power 2x50 / 1x150 W Fig. 7 2x100 / 1x300 W

4 Ohm (THD @ 0.04 %) (THD @ 0.04 %)

RMS Power 2x75 / 1x200 W Fig. 7 2x150 / 1x 500 W

2 Ohm (THD @ 0.06 %) (THD @ 0.05 %)

RMS Power 2x115 W Fig. 7 2x200 W

1 Ohm (THD @ 0.07 %) (THD @ 0.07 %)

Freq. response 10 Hz - 70 kHz 10 Hz - 70 kHz

- 3 dB

Signal-to-Noise > 95 dB > 95 dB

Ratio

Input Level 0,3 - 8 V 0,3 - 8 V

High Pass 40 - 250 Hz 40 - 250 Hz

Low Pass 40 - 120 Hz 40 - 120 Hz

Dimensions 232.6 x 59.5 x 320 232.6 x 59.5 x 380

WxHxD (mm)

Tri-Mode

Allows you to drive two loudspeakers and to connect a third speaker

in mono operation (bridged mode).

Positive/negative connections

We recommend a minimum cross-section of 10 mm

. Lay commercially

available positive cable to the battery and connect using fuse holder. The

fuse holder should be connected close to the battery.

Use cable bushings at sharp-edged holes. Screw the commercially

available negative cable firmly to an interference-free earthing-point (car

body bolt, car body sheet, but not to the negative battery pole). Scrape

the contact surface of the earthing point until it is blank metal and coat

with graphite grease.

Connection examples:

Connection of power supply........................................................ Fig. 2

Connection of car radio with cinch socket ................................... Fig. 3

Connection of car radio with loudspeaker output ........................ Fig. 4

Loudspeaker connections ........................................................... Fig. 5

When connecting via the cinch or loudspeaker sockets of the car radio

the switch cable must be connected.

+12V

Controller (GAIN)

Using the Gain Controller you can adjust the input sensitivity of the

Velocity Power Amplifier to the output voltage of your car radio pre-

amplifier output.

The adjusting range is from 0.3 V to 8 V.

When connecting a car radio from other manufacturers the input sensitivity

should be adapted in accordance with the specifications of the

manufacturer.

Introduction (GB)

Congratulations on purchasing this high-quality Car Audio Amplifier. The

development work invested in the new Velocity Amplifier offers you

complete music enjoyment in your car. Our Velocity Amplifiers are fitted

with all typical product features expected from a high-end amplifier, but

also contain a number of technical highlights as well, such as:

• 1 ohm stability (only in stereo mode) for low-ohm amplifier systems

with high performance

• Variable frequency dividers for high and low pass setting

• Variable input voltage 0.3 - 8 V

• Transistors for power supply using MOSPET technology

• Gold-plated screw connectors for loudspeaker and power supply

• Preamp-Out and -In gold-plated

• Bass-Boost

• Chrome-plated amplifier housing

To achieve the best possible sound quality from your new Velocity

Amplifier we recommend that it is installed by an authorised Velocity

dealer and that the matching Velocity Loudspeaker system is used. This

is the way to obtain the full enjoyment of the performance of your

amplifier.

Let us finally mention the aspect of health safety. Please remember when

listening to music in your car that constant sound-pressure levels of more

than 100 dB can cause permanent damage to the human ear right up to

complete loss of hearing. Sound-pressure levels of more than 130 dB

can be achieved with modern high-performance systems and high-

quality loudspeaker configurations.

You can also obtain further information on our Velocity Series at our

Internet address http://www.velocity.de

Safety instructions

Rules to be observed in fitting and connection

Disconnect the negative pole of the car battery for the duration of the

installation and connection works.

The safety instructions of the car manufacturer (airbag, alarm systems,

on-board computers, engine immobilizers) must be observed.

With regard to accident prevention the Velocity power amplifier must be

affixed in a professional manner. The mounting surface must be suitable

for accepting the enclosed screws and must offer secure installation.

When drilling holes please ensure that no car components are damaged

(battery, cables, fuse box).

The amplifier should be installed at a suitable location, i.e. under the

seats or in the boot, Fig. 1.

A dry position should be selected for the installation location that

guarantees sufficient air circulation for the cooling of the amplifier.

Use cable bushings at sharp-edged holes.

Use loudspeakers with 1-2-4 ohm impedance. Pay attention to the max.

loading (music output).

Use 16 mm

loudspeaker connection cables. Do not connect the

loudspeakers to earth, use only the designated terminals.

The cross-section of the positive and negative cable may not be less than

10 mm

Fit a fuse holder to the positive cable between the battery and the

amplifier directly at the battery.

8 622 401 876

Blaupunkt vr 2100 velocity Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info