Bedienungsanleitung Blomberg WNF 6380 WE20 (Seite 3 von 68) (Englisch)

581514

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

• Donotplacetheproductonthepowercable.

• Donotinstalltheproductatplaceswhere

temperaturemayfallbelow0ºC.

• Placetheproductatleast1cmawayfromthe

edges of other furniture.

Removing packaging reinforcement

Tiltthemachinebackwardstoremovethepackaging

reinforcement. Remove the packaging reinforcement

bypullingtheribbon.

Removing the transportation locks

 Donotremovethetransportationlocksbefore

taking out the packaging reinforcement.

 Removethetransportationsafetyboltsbefore

operating the washing machine, otherwise, the

productwillbedamaged.

1. Loosenalltheboltswithaspanneruntilthey

rotate freely (C).

2. Removetransportationsafetyboltsbyturning

them gently.

3. AttachtheplasticcoverssuppliedintheUser

Manualbagintotheholesontherearpanel.(P)

 Keepthetransportationsafetyboltsinasafe

place to reuse when the washing machine

needstobemovedagaininthefuture.

Never move the product without the

transportationsafetyboltsproperlyfixedin

place!

Connecting water supply

 Thewatersupplypressurerequiredtorunthe

productisbetween1to10bars(0.1–10MPa).

Itisnecessarytohave10–80litersofwater

flowing from the fully open tap in one minute

to have your machine run smoothly. Attach a

pressure reducing valve if water pressure is

higher.

 Ifyouaregoingtousethedoublewater-inlet

productasasingle(cold)water-inletunit,you

must install the supplied stopper to the hot

watervalvebeforeoperatingtheproduct.

(Appliesfortheproductssuppliedwithablind

stopper group.)

 Ifyouwanttousebothwaterinletsofthe

product, connect the hot water hose after

removing the stopper and gasket group from

the hot water valve. (Applies for the products

suppliedwithablindstoppergroup.)

 Modelswithasinglewaterinletshouldnotbe

connectedtothehotwatertap.Insuchacase

the laundry will get damaged or the product will

switch to protection mode and will not operate.

 Donotuseoldorusedwaterinlethoseson

thenewproduct.Itmaycausestainsonyour

laundry.

1. Connect the special hoses supplied with the

product to the water inlets on the product. Red

hose(left)(max.90ºC)isforhotwaterinlet,blue

hose(right)(max.25ºC)isforcoldwaterinlet.

Ensure that the cold and hot water connections

are made correctly when installing the product.

Otherwise,yourlaundrywillcomeouthotatthe

end of the washing process and wear out.

2. Tightenallhosenutsbyhand.Neverusea

wrench when tightening the nuts.

3. Openthetapscompletelyaftermakingthe

hose connection to check for water leaks at

theconnectionpoints.Ifanyleaksoccur,turn

off the tap and remove the nut. Retighten the

nut carefully after checking the seal. To prevent

waterleakagesanddamagescausedbythem,

keep the taps closed when the machine is not

in use.

Connecting to the drain

• Theendofthedrainhosemustbedirectly

connected to the wastewater drain or to the

washbasin.

 Yourhousewillbefloodedifthehosecomes

out of its housing during water discharge.

Moreover, there is risk of scalding due to

high washing temperatures! To prevent such

situations and to ensure smooth water intake

and discharge of the machine, fix the end of the

discharge hose tightly so that it cannot come

out.

• Thehoseshouldbeattachedtoaheightofat

least 40 cm, and 100 cm at most.

• Incasethehoseiselevatedafterlayingiton

the floor level or close to the ground (less than

40cmabovetheground),waterdischarge

becomesmoredifficultandthelaundrymay

come out excessively wet. Therefore, follow the

heightsdescribedinthefigure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blomberg WNF 6380 WE20 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info