Bedienungsanleitung Bluesound Pulse Sub (Seite 3 von 8) (Englisch)

676381

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

CROSSOVER FREQUENCY CONTROL: Adjusts the upper limit of the subwoofer’s frequency range. Continuously variable

from 50Hz to 150Hz for precise matching of subwoofer bass reproduction with other speaker(s) in your system. The

default crossover frequency is set at 130 Hz, for use with the PULSE SOUNDBAR 2i.

PHASE CONTROL: Selects the subwoofer output phase between in-phase (0˚) and out-of-phase (180˚) to compensate for

the low to mid bass acoustic effects of different placement locations and listening rooms. The default phase setting is 0˚.

See “Subwoofer Placement” for more information.

POWER MODE SWITCH: Selects the power mode for the PULSE SUB. Select “ON” and Standby Mode is disabled; the

PULSE SUB is on all of the time. Select “AUTO” and the PULSE SUB will go to Standby Mode, automatically powering up

when required and returning to standby after 20 minutes of inactivity. Select “OFF” and the PULSE SUB will not turn on.

The default position for the power switch is AUTO.

VOLUME CONTROL: Adjusts the output level of the PULSE SUB only: This is not intended as a day-to-day volume

control.

INDICATOR LIGHT: Located on the front of the PULSE SUB. The light indicates power-on and wireless connectivity status.

LOW/LINE LEVEL INPUT: For connecting the PULSE SUB to a separate component preamplier, or to an integrated

amplier or receiver with preamplier-out/main-in connections, at line level.

LFE: For connecting the PULSE SUB to a separate component preamplier, or to an integrated amplier or receiver with

LFE/Subwoofer output connections. Not recommended for use with Bluesound Players.

LOW/LINE LEVEL OUTPUT: For connecting the PULSE SUB to a separate component preamplier, or to an integrated

amplier or receiver with preamplier-out/main-in connections, at line level.

PAIRING BUTTON: To put the PULSE SUB into wireless pairing mode, press and hold the pairing button for 5 seconds,

then release. The front indicator light will blink GREEN for approximately 6 seconds, indicating the PULSE SUB is in

pairing mode. The PULSE SUB will remain in pairing mode for approximately 60 seconds.

POWER SWITCH: The Power Switch turns off the subwoofer’s internal amplier.

AC MAINS INPUT: The PULSE SUB comes supplied with two separate AC power cords. Select the AC power cord

appropriate for your region. Before connecting the plug to the wall outlet, rmly connect the other end of the AC power cord

to the AC Mains input socket. Never force the plug into the wall outlet. An adapter may be necessary in certain regions.

Always disconnect the plug from the wall outlet rst, before disconnecting the cable from the PULSE SUB’s AC Mains

input socket.

The default volume is set

at level 7, for use with the

PULSE SOUNDBAR 2i using

a wireless connection.

The recommended volume for a

wired connection to the PULSE

SOUNDBAR 2i is level 5.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bluesound Pulse Sub Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bluesound Pulse Sub

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info