Bedienungsanleitung BodySculpture BE-5945 (Seite 13 von 15) (Englisch)

573538

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

EXERCISE COMPUTER

FUNCTION BUTTON

MODE PRESS TO SELECT FUNCTION DISPLAY, AND HOLD ON PRESSING FOR 4 SECONDS

TO HAVE ALL FUNCTION VALUES TOTAL RESET.

(THERE IS NO SINGLE FUNCTION RESET AVAILABLE.)

FUNCTIONS

SCAN: AUTOMATICALLY SCANS THROUGH EACH FUNCTION EVERY 6 SECONDS.

TIME: DISPLAYS THE ACCUMULATED TIME UP TO 99:59 DURING EXERCISING.

SPEED: DISPLAYS THE CURRENT SPEED UP TO 999.9KM/H OR ML/H, THE VALUE WILL STAY ON THE

MONITOR CONSTANTLY.

DISTANCE: DISPLAYS THE ACCUMULATED DISTANCE UP TO 99.99 KM OR ML DURING EXERCISING.

RPM: DISPLAYS CURRENT ROTATION PER MINUTE.

CALORIES: DISPLAYS THE ACCUMULATED CALORIE CONSUPMTION UP TO 999.9 CAL DURING

EXERCISING.

(THIS DATA IS A ROUGH GUIDE FOR COMPARISON OF DIFFERENT SESSIONS

EXERCISING SESSIONS THAT CAN NOT BE USED FOR MEDICAL TREATMENT.)

1. WHEN STOP EXERCISING, THERE WILL BE A STOP SIGN SHOWN ON THE UPPER-LEFT CORNER.

2. WITH NO SIGNAL TRANSMITTED INTO THE MONITOR IN A PERIOD OF 4 MINUTES, THE LCD

DISPLAY WILL SHUT OFF AUTOMATICALLY, AND ALL FUNCTION VALUES WILL BE STORED

3. TURN ON THE MONITOR BY PRESSING THE BUTTON OR START EXERCISING, ALL FUNCTION

VALUES(SPEED EXCLUDED) WILL START COUNTING FROM PREVIOUS DATAS.

4. IF IMPROPER DISPLAY ON MONITOR, PLS RE-INSTALL THE BATTERIES TO HAVE A GOOD

RESULT.

TROUBLE SHOOTING.

1. Change the battery. To change the computer battery, please slide the computer from the computer

holder, remove the battery cover on the back of the computer console, and remove the batteries. Replace

with 1 x AA batteries. Finally put the cover back on the console, and slide the computer back on the

computer holder.

2. Computer not working correctly

. If your computer is not working correctly, please check whether the

lower sensor wire is connected to the upper sensor wire, and make sure the upper sensor wire is plugged

into the computer. When you have checked the above, and the computer still not working, then please

make sure the batteries are installed correctly in the computer and that the batteries are still working.

3. No resistance.

If there is no tension resistance on the bike, please make sure the upper tension cable is

connected to the lower tension cable. Turn the tension knob anti-clockwise to it’s lowest level, then go to

the tension strap buckle which is situated on top of the flywheel cover at the base of the front post. Loosen

the tension strap, pull it through the buckle until you can feel some resistance on the strap then lock it back

around the buckle. Now mount the cycle and turn the pedals, the tension control knob can now be used

for a finer adjustment. If you find it is now too tight go back to the tension strap buckle and loosen the

strap slightly.

1. Before using the bike, always make sure all bolts/nuts are fully tightened.

2. A spent battery is hazardous waste, please dispose of it correctly, and do not throw it in the trash.

3. When eventually you want to scrap the machine, you should remove the batteries from the computer, and

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BodySculpture BE-5945 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info