Bedienungsanleitung Bort BWS-900U (Seite 6 von 56) (Alle Sprachen)

555120

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Angle grinder

INTENDED USE

This tool is intended for grinding, cutting and deburring

metal and stone materials without the use of water; with

the appropriate accessories the tool can also be used for

brushing and sanding

TECHNICAL SPECIFICATIONS 1

PRODUCT ELEMENTS 2

1. Spindle

2. Clamping ﬂ ange

3. Spanner

4. Spindle-lock button

5. Auxiliary handle

6. Safety guard

7. Mounting ﬂ ange

8. On/off locking switch

9. Switch-lock knob

SAFETY

WARNING! Read all instructions. Failure to follow all in-

structions listed below may result in electric shock, ﬁ re

and/or serious injury.

 Only use this tool for dry grinding/cutting

 Only use the ﬂ anges which are supplied with this tool

 This tool should not be used by people under the age of

16 years

 Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

 Use the original SBM Group accessories which can be

obtained from your SBM Group dealer

 For mounting/using non- SBM Group accessories ob-

serve the instructions of the manufacturer concerned

 Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

 Do not use damaged, deformed or vibrating grinding/

cutting discs

 Handle and store grinding/cutting discs carefully to

avoid chipping and cracking

 Protect accessories from impact, shock and grease

 Do not use a grinding/cutting disc that is larger than the

maximum recommended size

 Only use grinding/cutting discs with a hole diameter

which ﬁ ts mounting ﬂ ange (7) without play; never use

reducers or adaptors to ﬁ t large-hole grinding/cutting

discs

 Never use grinding/cutting discs with a threaded hole,

of which the thread is not long enough to accept the spin-

dle length of the tool

 Never use accessories with a “blind” threaded hole

smaller than M14 x 21 mm

OUTDOOR USE

 Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

 Only use an extension cord which is intended for out-

door use and equipped with a splashproof coupling-sock-

BEFORE USE

 Before using the tool for the ﬁ rst time, it is recommend-

ed to receive practical information

 Do not work materials containing asbestos (asbestos is

considered carcinogenic)

 Take protective measures when during work dust can

develop that is harmful to one’s health, combustible or ex-

plosive (some dusts are considered carcinogenic); wear a

dust mask and work with dust/chip extraction when con-

nectable

 Be careful of hidden electrical wires or gas- and water

pipes; check the work area, for instance with a metal de-

tector

 Be careful when cutting grooves, especially in support-

ing walls (slots in supporting walls are subject to country-

speciﬁ c regulations; these regulations are to be observed

under all circumstances)

 Clamp the workpiece in case it does not remain

stationa ry from its own weight

 Do not clamp the tool in a vice

 Use completely unrolled and safe extension cords with

a capacity of 16 Amps (UK 13 Amps)

 Wear protective glasses and gloves, hearing protection

and sturdy shoes; when necessary, also wear an apron

 Always mount auxiliary handle (5) and protective guard

(6); never use the tool without them

 Be sure tool is switched off when plugging in

DURING USE

 Always keep the cord away from moving parts of the

tool; direct the cord to the rear, away from the tool

 If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug;

never use the tool with a damaged cord

 Push spindle-lock button (4) only when spindle (1) is at

a standstill

 Keep hands away from rotating accessories

 When grinding metal, sparks are generated; keep other

persons and combustible material from work area

 In case of electrical or mechanical malfunction, immedi-

ately switch off the tool and disconnect the plug

 In case the cutting disc is blocked, resulting in jerking

forces on the tool, immediately switch off the tool

 In case of current interruption or when the plug is ac-

cidentally pulled out, unlock the on/off switch (8) imme-

diately and put it in the OFF-position in order to prevent

uncontrolled restarting

 Do not apply so much pressure on the tool that it comes

to a standstill

AFTER USE

 Before you put down the tool, switch off the motor and

ensure that all moving parts have come to a complete

standstill

 After switching off the tool, never stop the rotation of the

accessory by a lateral force applied against it

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

 Do not connect the blue (= neutral) or brown (= live)

wire in the cord of this tool to the earth terminal of the

plug

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bort BWS-900U Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info