Bedienungsanleitung Bosch DWK97JQ60B (Seite 19 von 20) (Englisch)

746911

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

en Installation

Fitting with a flue duct Fitting without a flue duct

Installation

Screw in the mounting supports for the extractor hood

until they are hand-tight, use a spirit level to level the

appliance and then screw the mounting supports in

fully.

[

PP

PP

PP

PP

PP

PP

PP

PP

PP

PP

[

PP

[

PP

PP

PP

PP

PP

PP

PP

PP

Installation en

Wall-mounting the appliance and levelling it

1. First remove the protective film from the back of the

appliance and, following installation, remove the rest

of the film.

2. When mounting the appliance, ensure that it

engages properly with the mounting supports.

3. If required, the appliance can be moved to the right

or to the left.

4. Firmly tighten the screws for the mounting supports.

Hold the bracket firmly when doing so.

5. If no duct is to be fitted, screw in the two locking

screws without the bracket. ©

Connecting the pipes

If the extractor hood is to be operated in exhaust-air

mode, the pipes must be connected. If the extractor

hood is to be operated in air-recirculation mode, an

optional accessory must be fitted. To do this, refer to

the installation instructions provided.

Note: If an aluminium pipe is being used, smooth the

connection area beforehand.

Exhaust air pipe, dia. 150 mm (recommended size)

Fit the exhaust air pipe directly to the air-pipe connector

and seal the joint.

Exhaust air pipe, dia. 120 mm

1. Fit the reducing connector directly to the air-pipe

connector.

2. Attach the exhaust air pipe to the reducing

connector.

3. Use suitable means to seal both joints.

Attaching the flue duct

If the extractor hood is to be operated in exhaust-air

mode, a flue duct must be fitted.

The flue duct does not need to be fitted for air-

recirculation mode.

:Warning

Risk of injury!

From sharp edges during installation. Always wear

protective gloves while installing the appliance.

:Warning

Risk of electric shock!

Components inside the appliance may have sharp

edges. These may damage the connecting cable. Do

not kink or pinch the connecting cable during

installation.

1. Separate the flue duct sections by removing the

adhesive tape.

2. Remove the pieces of protective film from both flue

duct sections.

3. Push one flue duct section into the other.

Notes

– To prevent scratches, lay paper over the edges of

the outer flue duct section to protect the surface.

– The slots of the inner flue duct section point

downwards.

4. Place flue ducts sections on the appliance.

5. Slide the inner flue duct section upwards, attach it to

the left and right sides of the retaining bracket, and

then slide it down to engage it.

6. Screw the flue duct section to the sides of the

retaining bracket using two screws.

7. Clip the lower flue duct section in at the retaining

bracket. The connection cable must not be

damaged. ª

Note: If an air-recirculation optional accessory has been

fitted and the extractor hood is to be operated without a

flue duct, the cable must be wound onto the connector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch DWK97JQ60B Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch DWK97JQ60B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info