Bedienungsanleitung Bosch PMF 1800 E Multitool (Seite 16 von 19) (Französisch)

708261

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

16 | English

1 609 92A 1PU | (13.11.15) Bosch Power Tools

Mounting/Replacing the Application Tool/Accessory

If required, remove an already mounted application tool/ac-

cessory.

For removing the application tool/accessory loosen the screw

7 with the hex key 8 and remove the tool.

Mount the application tool/accessory (e.g. plunge cut saw

blade 6) in such a way on the tool holder 5 that the openings

of the tool engage into the cams of the tool holder.

For a safe and fatigue-free working position it is possible to

position the application tools/accessories in any snap-in posi-

tions on the tool holder. Position the tool in such a way that

the depressed centre points downwards (marking on the tool

is readable from above, see figure on the graphics page).

Use the screw 7 to fasten the application tool/accessory.

Tightly fasten the screw 7 with the hex key 8.

 Check the tight seating of the application tool/accesso-

ry. Incorrect or not securely fastened application tools/

accessories can come loose during operation and pose a

hazard.

Mounting and Adjusting the Depth Stop

The depth stop 11 can be used when working with segment

saw blades, Riff-segment saw blades and segment blades.

If required, remove an already mounted application tool/ac-

cessory.

Slide the depth stop 11 over and beyond the tool holder 5 to

the stop onto the gear head of the power tool with the labelled

side facing upward.

The depth stop is intended for the following cutting depths:

– With segment saw blades ACZ 85 .. with a diameter of

85 mm: 8 mm, 10 mm, 12 mm and 14 mm cutting depths

(see indication on the depth stop in large font and not in

brackets).

– With segment saw blades ACZ 100 .. with a diameter of

100 mm: 14 mm, 16 mm, 18 mm and 20 mm cutting

depths (see indication on the depth stop in smaller font

and brackets).

Insert the appropriate segment saw blade for the desired cut-

ting depth. Slide the depth stop 11 from the tool holder 5 in

the direction of the application tool until you can rotate it free-

ly. Rotate the depth stop 11 so that the desired cutting depth

is above the section of the saw blade, which will be used to

saw. Slide the depth stop 11 once again to the stop onto the

gear head of the application tool.

For all other cutting depths and when working with other appli-

cation tools, remove the depth stop 11. For this, remove the

application tool and pull the depth stop from the gear head.

Mounting/Replacing a Sanding Sheet on the Sanding Plate

The sanding plate 9 is fitted with Velcro backing for quick and

easy fastening of sanding sheets with Velcro adhesion.

Before attaching the sanding sheet 10, free the Velcro back-

ing of the sanding plate 9 from any debris by tapping against

it in order to enable optimum adhesion.

Position the sanding sheet 10 flush alongside one edge of the

sanding plate 9, then lay the sanding sheet onto the sanding

plate and press firmly.

To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.

To remove the sanding sheet 10, grasp it at one of the tips and

pull it off from the sanding plate 9.

You can use all sanding sheets, fleece pads/polishing cloth

pads of the Delta 93 mm series of Bosch accessory program.

Sanding accessories, such as fleece pads/polishing cloth

pads, are attached to the sanding plate in the same manner.

BIM plunge cut saw

blades, metal

Metal (e. g. unhardened nails,

screws, smaller profiles),

non-ferrous metals

Smaller separating and plunge cuts;

example: shortening narrow profiles, cutting fastening

elements such as staples

HM-Riff segment

saw blade

Grouting joints, soft wall tiles,

glass-fibre reinforces plastic

and other abrasive materials

Cutting and separating close to edges, in corners or hard

to reach areas;

example: removing grouting joints between wall tiles for

repair work, cutting openings in tiles, gypsum boards or

plastic

HM-Riff delta plate

Mortar, concrete remainders,

wood, abrasive materials

Rasping and sanding on hard surfaces;

example: removing mortar or tile adhesive (e.g. when

replacing damaged tiles)

Scraper, rigid

Carpets, coverings Scraping on hard surfaces;

example: removing carpet and tile adhesive

BIM serrated seg-

ment saw blade

Insulation material, insulation

panels, floor panels, sound in-

sulation panels, cardboard,

carpet, rubber, leather

Cutting soft materials

Accessory Material Application

OBJ_BUCH-2516-002.book Page 16 Friday, November 13, 2015 9:25 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PMF 1800 E Multitool Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info