Bedienungsanleitung Bosch WR8..P... (Seite 5 von 12) (Englisch)

613842

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

56 720 607 884

2. Preconditions for installation

The appliance can only be sold in the countries mentioned

in the type plate.

2.1 Regulations

Gas safety (installation & use) Regulations 1998.

It is the law in GB that a competent Person in accordance

with the above regulations installs all gas appliances.

Failure to install appliances correctly could lead to

prosecution.

It is in your interest , and that of safety, to ensure compliance

with the law.

Caravan & holiday homes:

the installation must meet the following standards Bs 5482:2

LPG and EN721 ventilation.

2.2 Location

The appliance should be sited in a well ventilated room where

it will not be exposed to temperatures below freezing.

To prevent corrosion, the combustion air must not contain

any corrosive substances. Substances classed as corrosion-

promoting include halogenated hydrocarbons such as are

found in solvents, paints, adhesives, aerosol propellants and

various household cleaners. Appropriate measures should

be taken where necessary.

With the exception of the flue pipe, the surface temperature

of the appliance is below 85 °C. No special safety measures

are therefore necessary.

Site appliance as shown in Fig. 5.

Always site appliance in a location not exposed to

temperatures below freezing. If this is not possible, the

appliance must be switched off and drained and the batteries

removed whenever there is a risk of freezing.

Do not install the appliance in rooms where the free volume

is less than 8 m

Air admission

The room where the appliance is to be installed should be

provided of fresh air inlet areas according with the below

table.

Minimum requirements are listed above. Local regulations

should allways be observed.

2.3 Fixing the appliance

Remove the temperature control and the output control.

Remove the outer case by sliding it forwards and then lifting

upwards.

Fix the appliance using the sleeves and hooks supplied so

that it is vertical.

Never allow the appliance to rest against water or gas

pipes.

2.4 Water connection

It is advisable to drain the appliance before installing it as

any dirt or grit inside it could reduce the water flow rate and,

To prevent problems caused by sudden pressure fluctuations

in the water supply, it is advisable to fit a non-return valve

to the water outlet.

2.5 Gas connection

Take care to ensure dirt is not allowed to enter gas inlet.

Make sure that the type of gas specified on the appliance

type plate is the same as that supplied by the gas authorities.

Select pipe diameter to suit output of instantaneous water

heater being installed.

Fit gas service cock as close to appliance as possible.

Fig. 4 Water connection

in extreme cases, could completely clog up the appliance.

Mark hot water (fig.4, pos.B) and cold water pipes (fig.4,

pos.A) so as to prevent confusion.

Connect pipe to automatic water valve using the connecting

kit supplied.

Appliance Minimum area

WR 8

WR 11

≥ 60 cm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch WR8..P... Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info