Bedienungsanleitung Breezair EZ series (Seite 17 von 20) (Englisch)

517807

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Seasonal maintenance is only

required if you have a cooler fitted

with a bleed system. The following

pages outline the maintenance

required at the end of the season and

then at the start of the next season.

This ensures that your cooler

continues to operate efficiently.

If your cooler is fitted with a drain

valve no seasonal maintenance is

required. However, we require that

the following components and the

operation thereof, be checked after

the first year, then every 2 years as

routine maintenance.

(1)...... Belt drive.

(2)...... Pump.

(3)...... Drain valve.

(4)...... Solenoid and associated

filter.

(5)...... Fan motor operation and

current.

(6)...... Float valve.

Routine maintenance may be

required more frequently in adverse

environmental situations and very

dusty areas.

Note

Failure to carry out regular

maintenance will affect your

warranty coverage.

WARNING

As your cooler is mounted on the

roof, we suggest that any

maintenance or checks be carried

out by an authorised Breezair

dealer or service agent. Climbing

onto the roof can be hazardous

and could result in injury to you

and damage to your property.

END OF SEASON

(1).. Turn off the water supply to

the cooler.

(2)...Remove the pad frames as

shown on page 17.

(3)...Turn off the power at the

isolating switch inside the

cooler.

(4)...Check and clean the water

distributing channels

under the lid.

(5)....Unclip and remove the

bleed system as shown

below. Take care not to

lose the o-ring. This

removal will allow the

water to drain from the

tank throughout the winter.

(6)....Thoroughly clean the tank

and the pump filter. Do

not replace the bleed

system. If you do, water

will sit without draining

from the tank throughout

the winter months.

(7).... Refit the pad frames.

HEALTH REGULATIONS

In some states, regulations require

that evaporative air coolers be

serviced at specific intervals.

ILL1141-A

Evaporative Cooler

PRE-SEASON

NOTE: Do

not wash the pads with

high pressure water spray.

WARNING:

Do not run the cooler with

the pad frames removed.

(1)...Turn your main switchboard

power off.

(2)...Remove the pad frames as

shown in the next column.

(3)...Ensure the power is off at

the isolating switch inside the

cooler.

(4)...Gently wash the pad frames

to remove any dust build up

during the winter.

If the pads are salted-up

replace them.

(5)...Replace the bleed system

that was removed at the end

of the last season. Ensure

that the o-ring is in place and

that the tray is positioned so

that it can catch the water

from the pad.

(6)...Turn on the water supply to

the cooler.

(7)...Check for water leaks.

Check operation of float

valve.

(8)...Check if adj. required to belt

drive. Reset motor amps.

(9)...Switch on the isolating

switch.

(10).Refit the pad frames.

(11).Turn the power on at your

main switchboard.

(12).Run the cooler.

REMOVING PAD FRAMES

To remove a pad frame:

(1)...Remove the clips holding the

pad frame in place.

(2)...Insert a flat head screw

driver into the slot between

the lid and the top of the pad

frame. Lever it so the pad

frame is released.

(3)...... Take hold of the pad frame,

pivot it outwards and lift it up. Be

careful not to damage the pad.

Repeat the steps above with the 3

remaining pad frames.

(For EXH210 units only) There are

90mm pads fitted to the front and rear,

with 100mm pads fitted to the sides

(facing the fan scroll holes). These

pads must be re fitted to their original

positions, or the larger pads could

catch on the float valve or components

mounted on the scroll.

The 100mm pads can be identified by

a rebate at the base of the Chillcel.

If fitted incorrectly, a drop in

performance may be found, water

can bypass the pad and be carried

over into the airstream and ducting

and/or damage to the pads or

electronic components may occur.

ILL950-C

ILL187-E

SEELEY INTERNATIONAL – OWNER’S MANUAL 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Breezair EZ series Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info