SAFETY NO
6.
9. Pull on the base station t
both sides.
10. 07 is fully r
red mark at the top of the support leg 07 must
no longer be visible.
1 06 and pull
the support leg 07 out until it is secured against
the vehicle floor and the green mark 14 is fully
visible.
DANGER! The gr14 must be fully
visible on the support leg 07 . The support leg 07
must never be suspended in mid-air or support-
ed by other objects.
Ensure that the support leg 07 does not lift the
base station from the seat.
12. Only BAB F
the steps in chapt.
13. T
and push it with equal pressure on both sides t-
wards the vehicle backrest until the base station
is touching it.
Please take the time to r
keep them to hand in the designat13
on the base station at all times! The instructions must be kept
with the base station if the latter is passed on to a third party
DANGER! F
•
10 km/h, the base station may be damaged without the damage
becoming immediately visible. In this case the base station must
be replaced. Please dispose of it properly
•
(e.g if it falls on the ground).
•
chanical parts, in particular
• Never lubricate or oil parts of the base station.
•
Never leave your child unattended in the
infant carrier and base station
in the vehicle.
•
you place the infant carrier in the vehicle or take it out.
•
sunlight when they are not in use. The infant carrier can get very hot
in direct sunlight. Children's skin is sensitive and could be harmed.
•
The more snugly the belt fits over your child's body, the better they will
be protect
the belt.
•
base station and must not be removed.
•
periods of time. The semi-recumbent position in the infant carrier will
always put a strain on your baby's spine. T
infant carrier as often as possible – this includes int
rides. Do not keep your baby in the infant carrier once it has been
removed from the car
•
latch on the foldable rear seat bench).
•
or by holding onto them.
•
port leg.
DANGER! F
In the case of an emergency stop or an accident, unsecur
or objects may cause injury to other vehicle occupants. Please always
check that:
•
rear seat bench latch is engaged).
•
shelf
• all persons in the vehicle have their seatbelts fastened.
•
if no child is being transport
WARNING! F
•
T
base station
is not jammed in be-
tween hard objects (car door
•
Keep the
base station
in a safe place when it is not in use. Do not
place any heavy objects on the
base station
and do not store it dir
ly next to sour
CA
•
Certain car seat covers made from more sensitive mat
leather
seats. F
using the BRIT
sories.
P
2. Rotate the support leg 07 outwards until
it stops.
3. 05 and the red
release button 04 on both sides of the seat
towards each other
hooks on the ISOFIX locking arms 03 ar
and ready to use.
4. Pull the gr
11
towards the support leg
07
until the ISOFIX locking arms 03 ar
extended.
5. Place the base station against the direction
of travel on a suitable vehicle seat.
TIP: Depending on the design, there could
be a gap between the contact surface of the
base station and the vehicle seat. This does
not present a safety problem when using the
base station.
6. Position the two ISOFIX locking arms 03
directly in front of the two insertion aids 02 .
7. Push both ISOFIX locking arms 03 into the
insertion aids 02 until the ISOFIX locking
arms 03 engage on both sides with a clicking
sound.
DANGER! The gr05 must
be visible on both sides in order for the base sta-
tion to be properly fast
8. T
and push it with equal pressure on both sides
towards the vehicle backr
station is touching it.
DANGER! An airbag hitting the infant carrier can cause serious
injuries to your baby, possibly resulting in death.
Do not use the infant carrier and base station in passenger seats with
activated front airbags! F
instructions in your owner's manual.
INS
7.
Pr
1. If your vehicle is not fitted with ISOFIX insertion aids as standard,
clamp the two ISOFIX insertion aids 02 , which are included in the
scope of delivery of the seat*, with the cutout pointing upwards
to the two ISOFIX fast 01 of your vehicle.
TIP:
and the backrest of the vehicle seat.
* The insertion aids facilitate the installation of the child safety seat with the use of the ISOFIX
fastening points and prevent damage t
remove them and keep them in a safe place. F
need to be removed befor
Any problems which occur are usually caused by dirt or foreign objects on the insertion aids and
on the hooks. Remove soiling or external objects t
01
02
05
04
03
03
02
07
07
06
Removing the infant carrier from the base
station
DANGER! Ensur15 is in the
upper position A .
1.
Pull and hold the gr
16
.
2. Lift the infant carrier until the fixation prongs 17
release from the fixation slots 08 .
WARNING! K
er while doing this.
3. Remove the infant carrier from the base
station.
16
17
08
T
1.
P
2. Press and hold the gr
button 09 and, at the same time, pull the top
part of the base station 12 gr
Every time it clicks into the next level, check
if the inclination is sucient.
DANGER! When swivelling the t
of the base station 12 down, ensur
do not trap your fingers.
3. Set the inclination so that the inclination indica-
tor 10 is green.
DANGER! The base station cannot be used
if the inclination indicator 10 is red.
4. Release the grey inclination adjustment button
09 and check that the top part of the base
station is properly engaged.
DANGER! When installing the base station
in another vehicle, the inclination must again
be adjusted from the flatt
15
12
15
Fitting the infant carrier to the base station
DANGER! Ensur15 is in the
upper position A .
DANGER! Ensur
base station 12 is fr
1.
Place the infant carrier against the direction
of travel on the base station (baby is facing
backwards).
2. Snap the infant carrier into place so that
it makes an audible clicking sound.
3. Check if the indicators are green on both
sides.
DANGER! The indicat
on both sides.
4. Pull on the infant carrier handle 15 to check
it is fully engaged.
USING THE INF
9.
ADJUS
8.
Depending on the vehicle model, there can be dierences in the vehicle
seat inclination which can have an impact on your child’
It is always recommended that the seating position be as upright
as possible. Y
as your child’
Opening the ISOFIX
1.
Pull the gr
11
towards the support leg
07
.
2. Push the green safety butt04 and the red
release button 05 on both locking arms 03
towards each other
3.
Pull the gr
11
towards the support leg
07
and press both locking arms 03 at the same
time towards the support leg until they ar
retr
►The base station can now be removed.
DANGER! The child safety seat must always
be secured when it is in the vehicle, even
if no child is being transport
REMOV
DISASSEMBL
11.
04
05
DISPOSAL:
Please observe the waste disposal regulations in your country
Disposal of packaging Container for cardboard bo
Seat cover
Residual waste, thermal utilisation
Plastic parts According to the labelling in the
corresponding container
Metal parts Container for metals
Belt straps Container for polyester
Buckle and tongue Residual waste
F
check that:
►the ISOFIX locking arms 03 ar
ISOFIX fastening points 01 and that both safety buttons 05 ar
fully green,
►the support leg 07 rests firmly on the vehicle floor
mark 14 on the support leg foot is visible,
►the support leg 07 does not lift the base station fr
►the infant carrier is fully engaged in the base station,
►the infant carrier is only installed on the front passenger seat
if no front airbag can strike the infant carrier
►the infant carrier is fastened against the direction of tr
F
check that:
►the ISOFIX locking arms 03 ar
ISOFIX fastening points 01 and that both safety buttons 05 ar
fully green,
►the support leg 07 rests firmly on the vehicle floor
mark 14 on the support leg foot is visible,
►the support leg 07 does not lift the base station fr
►the infant carrier is fully engaged in the base station,
►the infant carrier is only installed on the front passenger seat
if no front airbag can strike the infant carrier
►the infant carrier is fastened against the direction of tr
CLEANING
10.
09
10
12
The plastic parts can be cleaned using soapy waternot use
harsh cleaning agents (such as solvents).
11
03
07
05
07
11
03
07
