Zoom out
Zoom in
Vorherige Seite
Nächste Seite
BRITAX RÖMER Kindersicherheit GmbH
Blaubeurer Strasse 71
D-89077 Ulm
T.: +49 (0) 731 9345-199/-299
F.: +49 (0) 731 9345-210
E.: service.de@britax.com
1 Churchill Way West
Hampshire SP10 3UW
United Kingdom
T.: +44 (0) 1264 333343
F.: +44 (0) 1264 334146
E.: service.uk@britax.com
Please take the time to read these instructions carefully and keep them
to hand in the intended storage compartment 05 on the child safety seat at
all times! The instructions must be kept with the child safety seat if the latter
is passed on to a third party.
DANGER! For the protection of your child:
In the event of an accident at a collision speed of more than 10km/h, the child
safety seat may be damaged without the damage becoming immediately visible. In
this case, the child safety seat must be replaced. Please dispose of it properly.
Always have your child safety seat checked if you suspect it may have been
damaged (e.g if it falls on the ground).
Regularly check all important parts for damage. Ensure that all mechanical parts,
in particular, are fully functional.
Never lubricate or oil parts of the child seat.
Never leave your child unattended in the child seat in the vehicle.
Only allow your child to enter and exit the vehicle on the pavement side.
Protect the child safety seat from intensive direct sunlight when it is not in use.
The child safety seat can get very hot in direct sunshine. Children's skin is sensi-
tive and could be harmed as a result.
The more snugly the belt fits over your child's body, the better they will be protected.
Avoid putting thick clothes on your child under the belt.
Take regular breaks on long journeys in order to give your child the opportunity to
run about and play.
Use on the rear seat: Move the front seat far enough forwards to ensure that your
child's feet cannot hit the backrest of the front seat (to prevent risk of injury).
If your child tries to open
the red ISOFIT safety button
or a buckle, stop the
vehicle as soon as it is safe to do so. Check whether the child safety seat is correctly
fastened and ensure that your child is correctly secured. Explain to your child the
dangers associated with their actions.
DANGER! For the protection of all vehicle occupants:
In the case of an emergency stop or an accident, unsecured persons or objects may
cause injury to other vehicle occupants. Please always check that:
the backrests of the vehicle seats are locked, e.g. that a foldable rear seat bench
latch is engaged.
all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are
all persons in the vehicle have their seat belts fastened.
the child safety seat is always secured when it is in the vehicle, even if no child is
being transported.
WARNING! For your protection when handling the child seat:
Never use the child safety seat free standing, not even for test sitting.
To avoid damage, ensure that the child safety seat is not jammed in between
hard objects (car door, seat rails, etc.).
Keep the child safety seat in a safe place when it is not in use. Do not place any
heavy objects on the seat and do not store it directly next to sources of heat or in
direct sunlight.
Please observe the instructions for using children's restraining systems in the operating
instructions of your vehicle. The seat can be used in vehicles with ISOFIX anchoring systems
(see type list) and in vehicles with a 3-point belt.
To determine which seats are approved for use with child safety seats that meet the
requirements for weight classes 9 to 18 kg and 15 to 36 kg, please refer to the operating
instructions of your vehicle.
9-36 kg
The EVOLVA 1-2-3 SL SICT is approved for two dierent methods of installation:
Group Installation method Means by which child
is secured
Section of
user instructions
1 (9-18 kg) Vehicle belt With 5-point harness A
1 (9-18 kg) Vehicle belt + soft latch With 5-point harness A
2+3 (15-36 kg) Vehicle belt Vehicle belt B
2+3 (15-36 kg) Vehicle belt + soft latch Vehicle belt B
a) This means that the child safety seat may only be used in vehicles that are listed in the enclosed
vehicle type list. This type list is consistently kept up to date.
The latest version can be obtained from us or from www.britax.com
You can use your child safety seat as follows:
In the direction of travel Yes
Against the direction of travel No 1)
With 2-point harness No
With 3-point belt 2) Yes
with ISOFIX fastening points (be-
tween seat surface and backrest)
On front passenger seat
Yes 3)
On outer rear seat Yes
On centre rear seat
(with 3-point belt)
Yes 4)
1) Use on a rearward-facing vehicle seat (e.g. in a van or minibus) is only permitted if the vehicle
seat is also approved for use by adults. The seat may not be in the area of eect of an airbag.
2) The safety belt must be approved to ECE R 16 or a comparable standard, e.g. see whether
there is an "E" or "e" in a circle on the belt test label.
3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions
in the vehicle owner's manual.
4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.
Please observe the waste disposal regulations in your country.
Disposal of packaging Container for cardboard boxes
Seat cover Residual waste, waste incineration
Plastic parts To be placed in the corresponding
container according to labelling
Metal parts Container for metals
Belt straps Container for polyester
Buckle and tongue Residual waste
Please ensure that you only use original BRITAX RÖMER replacement
covers, as the seat cover is an integral part of the child safety seat and fulls
important functions to ensure the smooth operation of the system. Replace-
ment covers are available from your dealer.
The cover can be removed and washed in accordance with the instruc-
tions on the wash care label.
The plastic parts can be cleaned using soapy water. Do not use any caus-
tic cleaning agents (such as solvents).
DANGER! The child seat must not be used without the seat cover.
CAUTION! Never remove the buckle tongues 30 from the straps.
9 to 36 kg
(~9 months to
12 years of age)
2000025513 16/08
User instructions
Removing the 5-point harness
1. Loosen the harness straps as far as possible (see 9.1).
2. Push the shoulder strap adjuster 24 all the way up
(see 8.1).
3. Unhook the shoulder straps 13 from the connecting
piece 14 .
4. Clip the connecting piece 14 at the bottom of the
backrest 04 into its holder 11 .
5. Push down the strap loops of the shoulder pads 18
from the base of the shoulder strap adjuster 24 .
6. Pull the shoulder straps 13 and the strap loops of the
shoulder pads 18 out of the belt slots.
7. Undo the Velcro fastener on the crotch cushion 21 and
remove it.
8. On the bottom of the seat, unhook the adjusting strap
23 from the metal plate 27 .
9. Turn the metal plate 27 (that holds the harness buckle
19 to the seat shell) on end and push it upwards
through the belt slot 28 .
10. Release the harness buckle 19 .
11. Push the straps and buckle tongues 30 through the lap
belt slots in the cover.
12. Place the harness buckle 19 under the cover and inside
the storage compartment 31 of the backrest 04 .
13. Push the adjusting strap 23 under the cover.
14. Fix the shoulder pads 18 and shoulder straps 13 in the
rubber loops 32 at the feed-through points 15 .
Installing the 5-point harness
To install the straps, follow the steps in reverse order.
DANGER! Tug on the shoulder straps firmly 13 to make
sure that the 5-point harness is secure.
Removing the cover
1. Adjust the headrest by moving it up 16 (see 9.1).
2. Unhook the edge of the cover and the rubber loops on
the back of the headrest 16 .
3. Pull o the cover of the headrest 16 .
4. Unhook the rubber loops from the retaining screws on
the backrest 04 .
5. Loosen the shoulder straps 13 (see 9.2).
6. Undo the Velcro fastener on the crotch cushion
21 and
remove it.
7. Open the snaps
on the left and right-hand sides of the
backrest cover
04 .
8. Unthread the harness buckle
19 and the adjusting strap
23 from the cover.
9. On the bottom of the seat, unhook the rubber loop of
the cover from the retaining screws and cover flaps 24 .
10. Working from the side, carefully pull the edge of the
cover on the backrest 04 over the SICT 08 .
11. Slide the cover with opening over the headrest 16 .
The cover can now be washed in accordance with the
instructions on the wash care label.
Re-fitting the cover
Proceed in reverse order to re-fit the cover.
WARNING! Ensure that the straps are not twisted and
that they have been correctly inserted in the belt slots on
the cover.
To ensure the safety of your child, it is absolutely essential that the harness
buckle continues to function correctly. Harness buckle malfunctions are usually
caused by a build-up of soiling or by external objects.
Possible faults:
When you press the red release button, it takes a long time for the buckle
tongues to be ejected.
The buckle tongues no longer engage (i.e. when you try to push them in, they
pop out again).
The buckle tongues engage without an audible "click".
The buckle tongues are dicult to push in (you feel a certain amount of
Remedy: Clean the harness buckle so that it functions properly again:
Cleaning the harness buckle
1. Remove the harness buckle 19 (see 5.1).
2. Soak the buckle 19 in warm water containing washing-up
liquid for at least an hour.
3. Rinse the buckle 19 thoroughly and dry it.
4. Turn the metal plate 27 on end and push it downwards
through the belt slot 28 in the cover and through the
seat shell.
5. Turn the metal plate 27 90° and hook the adjusting strap
23 into the metal plate 27 (5.8).
DANGER! Tug hard on the harness buckle 19 to make
sure that it is secure.
6. Push the crotch cushion 21 into the belt slot and use the
Velcro fastener to fix it to the harness buckle.
01 02
01 ISOFIX fastening points (car) 06 ISOFIT Locking button
02 ISOFIX insertion aids 07 ISOFIT locking arms
03 Headrest adjuster 08 SICT
04 Backrest 09 Cover flap
Compartment for the user instructions
10 ISOFIT adjustment button
If you have any questions regarding the use of the product, please feel free to contact us:
Vehicle child
safety seat
Tested and approved according to ECE* R 44/04
*ECE = European Standard for Child Safety Equipment
Group Body weight
I 9 to 18 kg
II+III 15 to 36 kg
The child safety seat has been designed, tested and approved according
to the requirements of the European Standard for Child Safety Equipment
(ECER44/04). The seal of approval E (in a circle) and the approval number are
located on the orange approval label (sticker on the child safety seat).
DANGER! This approval will be invalidated if you make any modifications to
the child safety seat. Only the manufacturer is permitted to make modifica-
tions to the child safety seat.
WARNING! Use the EVOLVA 1-2-3 SL SICT exclusively for securing your
child in your vehicle. It is in no way suitable for use as a seat or toy in the
DANGER! Never secure your child or the child safety seat with a 2-point
belt. If you secure your child in the child seat with only a 2-point belt, this
may cause serious injuries to your child in the event of an accident and could
even result in their death.
DANGER! Never use installation method A for the child safety seat unless
the harness buckle and shoulder pads are properly attached (the straight
edges of the shoulder pads must be pointing towards each other). Make
sure that the metal plate of the harness buckle is correctly attached.
WARNING! Ensure that the straps are not twisted, that they have not been
accidentally interchanged and that they have been correctly inserted in the
belt slots on the cover.
23 27
13 14
160908_EVOLVA_123_SICT_DRAFT_GB_GRAFIKEN.indd 1 9/7/2016 9:04:53 PM

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.


Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.


Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Britax-Romer EVOLVA 1-2-3 SL SICT wenn:

Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.

Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von Britax-Romer EVOLVA 1-2-3 SL SICT in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 1,07 mb groß.


Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Andere Handbücher von Britax-Romer EVOLVA 1-2-3 SL SICT

Britax-Romer EVOLVA 1-2-3 SL SICT Bedienungsanleitung - Deutsch - 2 seiten

Britax-Romer EVOLVA 1-2-3 SL SICT Bedienungsanleitung - Holländisch - 2 seiten

Britax-Romer EVOLVA 1-2-3 SL SICT Bedienungsanleitung - Französisch - 2 seiten

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.