Bedienungsanleitung Bruder Mannesmann 12330 (Seite 1 von 5) (Deutsch, Englisch)

666580

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Finishing Sander

item-no. 12330

This tool is interference-suppressed

according to

CE EN 55014 + EN 61000

I N S T R U C T I O N - M A N U A L

Before using electric power-tools, please read and

understand the attached safety-instructions!

Additional safety-hints for impact-drill:

• Always wear safety-goggles and a dust-mask

during your work with the finishing-sander.

• Always secure the workpiece by clamps or else to

avoid slipping away.

• Make sure, that there are no nails, screws or other

metal-parts in your workpiece, before starting your

job.

• Always keep the holes in the baseplate clean from

dust.

• Always connect a vacuum cleaner to the attached

adaptor during your work.

Description

1. front-handle

2. on-/off-switch

3. lock button

4. handle

5. sanding paper

6. base plate

7. paper clamp

8. adaptor for vacuum-cleaner

9. power cord

Technichal dates

voltage 230 V AC∼ / 50 Hz

power input 150 W

sanding area 187 x 90 mm

sandpaper-size 230 x 90 mm

no. of vibrations 10.000 min

-1

sound pressure level (LPA) 80,0 dB(A)

sound power level (LWA) 93,0 dB(A)

vibration 2,5 m/s²

(acc. to EN 50144/13)

protection class / II

weight 1,29 kgs

Always wear safety-goggles, dust-mask and ear-

protection, when machine is in use!

Recommended nominal operating time: approx. 20

minutes under permanent load.

Rest after permanent operation: approx. 5-10

minutes.

Fastening of sanding-paper

• Disconnect the tool from the power-supply

before changing sanding paper.

• Open the paper-clamps on both sides of the

base-plate and remove the worn-out sanding-

paper.

• Place a new sanding-paper on the base-plate

observing the holes in the sanding-paper fit to

the holes of the base-plate.

• Bend the paper to the base-plate and fasten one

clamp first. Press the sanding-paper against the

base-plate, bend the other end and fasten

second clamp.

• Attention: This finishing sander is not suit-

able for wet-sanding jobs.

Operation

• To start the sander pull the trigger upwards

• For continious operation press the lock-button at

the same time.

• To stop the machine, pull the trigger again and

release.

• Put the sander on the workpiece, as soon as the

motor has reached its maximum speed.

• Let the sander slide smoothly over the surface of

your workpiece and do not apply too much

pressure. This will lead to reduce the speed, to

increase the wear of the sanding-paper and the

motor and to an uneven surface.

• Stop the sander only after having lifted from the

workpiece.

• Do not use the sander without sanding-paper.

• Do not cover the ventilation-slots by your hands,

in order to achieve adequate cooling of the

motor.

Maintenance

• The sander has no need to be maintained.

• Before cleaning the sander, be sure to

disconnect the machine from the power-supply.

• Only use a dry brush or cloth for cleaning the

housing from sanding-dust.

• Do not use any detergents, since they will attack

the plastic-housing and do not let any liquids

enter the inside of the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bruder Mannesmann 12330 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info