Bedienungsanleitung Bruder Mannesmann 12420 (Seite 8 von 27) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

666477

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

GB - 8

Always wear eye protection during use!

• The vibration emission level given in this information sheet has been measured in accordance with a

standardized test given in EN 60745 and may be used to compare one tool with another.

• The vibration emission level will vary because of the ways in which a power tool can be used and may

increase above the level given in this information sheet. This could lead to a significant underestimate of

exposure when the tool is used regularly in such a way.

• Note: To be accurate, an estimation of the level of exposure to vibration experienced during a given period of

work should also take into account the times when the tool is switched off and when it is running but not

actually doing the job. This may significantly reduce the exposure level over the total working period.

Suitable nails and staples:

You can use staples with a length up to 25 mm or nails with a length up to 32 mm with this electric staple gun.

Staples Nails

Bosch Typ 55 Bosch Typ 47

KWB Typ 055 KWB Typ 055

Novus C Typ 4 Novus E Typ J

Prebena Typ ES Prebena Typ J

Rapid Nr. 606 Rapid No. 8

Wolfcraft Typ 055 Wolfcraft Typ 062

Loading of staples (Fig. 3) or nails (Fig. 4)

• Unplug the tool from the mains.

• Push the staple feeder catch (7) at the back of the tool towards the magazine, and pull out the staple feeder

(5).

• Warning: Once the staple or nail strip has been placed in the feeder, it will be spring-loaded. Hold the catch

firmly to prevent the feeder from suddenly being ejecting from the tool.

• Place the staple strip (Fig. 3) or nail strip (Fig. 4) into the magazine.

• Push the staple feeder (5) back to the front and secure by hitching the catch (7) behind the opening in the

housing.

Usage

The tool has double protection against inadvertent operation:

1. Switch the main switch (4) to the "Off" position (0) to lock the trigger (1).

2. The contact switch (6) ensures that the staple gun is only triggered on contact with a material surface.

• Place the opening of the electric staple gun firmly onto the material and squeeze the trigger (1).

• Additional pressure applied to the front of the tool will prevent recoil and increase the force applied to the nails

or staples. This is especially important for ensuring that the nail or staple is driven the whole way into a hard

surface.

Hammer-force Preselection

With the thumbwheel for hammer-force preselection (3), it is possible to preselect the required hammer force.

The required hammer force depends on the length of the staples or nails, and on the strength of the material.

Always test the selected hammer force on scrap material first.

The optimum hammer-force setting can be determined only by trial and error.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bruder Mannesmann 12420 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info