Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
C7200G ENGLISH
USER MANUAL
DVD7200BT
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Inhalt der Seiten


  • Page 1

    C7200G

    ENGLISH

    USER MANUAL

    DVD7200BT

  • Page 2

    DVD7200BT

    ENGLISH
    Copyright Information

    ©2008 Rho-Delta Automotive & Consumer Products BV. All rights reserved. This
    document may not in whole or in part be reproduced, stored in a retrieval system,
    transmitted in any form or by any means, electronic, mechanical, photocopying,
    recording, or otherwise, or reduced to any electronic medium or machine-readable form
    without prior consent, in writing, from Rho-Delta Automotive & Consumer Products BV.
    DVD7200BT and Bullit are registered trademarks of Rho-Delta Automotive & Consumer
    Products BV. The logo’s, standards, software, and/or product names mentioned herein
    are manufacturer and publisher trademarks and are used only for the purpose of
    identification.
    Disclaimer
    The publishers and author assume no responsibility whatsoever for the uses made of this
    material or for decisions based on its use. Further, Rho-Delta Automotive & Consumer
    Products BV makes no warranties, either expressed or implied, regarding the contents of
    this product, its completeness, accuracy, merchantability, or fitness for any particular
    purpose. Neither the publisher nor anyone else who has been involved with the creating,
    production, or delivery of the material shall be liable for any reason. Rho-Delta
    Automotive & Consumer Products BV may make improvements and/or changes in the
    products and/or options described in this document at any time and without notice.
    All brand and product names used throughout this document are trademarks or
    registered trademarks of their respective companies. The brand and product names are
    used in editorial fashion only and for the benefit of such companies. No such use, or the
    use of any trade name, is intended to convey endorsement or other affiliation with the
    document.
    Product specifications are subject to change without prior notice
    www.rhodelta.nl

    WEEE (Waste Electrical and Electronic Equipment Directive)
    If at any time in the future you should need to dispose of this product
    please note that: Waste electrical products should not be disposed of with
    household waste. Please recycle where facilities exist. Check with your
    Local Authority or retailer for recycling advice.
    Disposing of the battery / batteries
    Please check local regulations for disposal of batteries or call your local city office or your
    household waste disposal service or the shop where you purchased the product.
    The battery / batteries should never be placed in municipal waste. Use a battery disposal
    facility in your neighborhood or community, if available.

  • Page 3

    DVD7200BT

    ENGLISH

    Dear Customer,
    Thank you for selecting our DVD7200BT. In order for you to utilize this device and all its
    options, we recommend that you read the corresponding instructions in this manual before
    the initial use of the device, even if you’re familiar with handling electronic devices. Please
    pay particular attention to the chapter “Important safety instructions” on page 7. Store this
    manual in a safe location for future reference. The descriptions and features in this manual
    only serve as general information and do not represent a guarantee. In order to offer you a
    product of the highest quality, we reserve the right to make possible improvements or
    changes without prior notification.
    Important safety instructions
    Please read and strictly observe the following instructions!
    -

    -

    -

    -

    -

    -

    -

    Never open the case of the car radio; it does not contain any serviceable parts! If
    the case is open, there is a risk of fatality due to electric shock.
    Do not give your car radio and especially the accessories to children. Never let your
    children use electrical devices without supervision. Children are not always able to
    recognize potential hazards. Also keep the packaging films away from children.
    There is a danger of suffocation.
    The car radio and the accompanying components may not be exposed to dripping
    or sprayed water. Make sure that no containers filled with liquid, such as e.g. cups
    or bottles, are placed in the vicinity of the device.
    Make sure that the display is not exposed to any bumps. This could damage the
    display.
    Please familiarize yourself with the different functions of your device before you
    begin driving. Excessively high volumes can pose a risk for you and other people in
    traffic. Therefore always select the volume at such a level that environmental
    sounds (horns, sirens, etc.) can still be perceived.
    Don’t use the car radio at an excessive volume. This poses a risk to your hearing.
    Please only perform lengthy changes of the device settings while the vehicle is
    parked. Your concentration might be affected by the changes.
    Only install the device in such a manner that safe driving is assured.
    Install the device in such a manner that it doesn't impede the driver and can't injure
    any of the vehicle’s occupants in the event of emergency braking.
    Don’t flip the monitor open by hand. This could damage the mechanics.
    The TFT color monitor consists of glass and liquid crystals. Don’t put any excessive
    pressure on the monitor, since otherwise it might scratch, break, or sustain other
    damages. In addition, the image quality might be impaired.
    Don’t touch the monitor surface with hard objects and only clean it with a soft, dry
    cloth and special TFT cleaner.
    Don’t use the device for a longer period while the vehicle's engine isn't running. This
    could drain the vehicle battery to the degree that the car can no longer be started. In
    addition, this might reduce the lifespan of the battery.
    Don’t park your vehicle in direct sunlight for extended periods, otherwise the
    temperature in the car’s interior could rise to the point that the device overheats and
    causes malfunctions. If possible, cool the interior of the vehicle in order to ensure that
    the device will operate properly.
    Only let the device be installed by qualified vehicle technicians.
    Before the final installation of the device into a DIN insertion compartment in the
    dashboard, connect the cables and test the connections.
    Only use the accessories included in the delivery. Usage of unauthorized
    components can cause damages.

  • Page 4

    DVD7200BT
    -

    -

    -

    -

    -

    -

    -

    -

    -

    -

    ENGLISH

    If you need to drill holes or make other changes for the installation, consult a
    specialized workshop in your area.
    This device is designed for a vehicle power supply of 12 V with the ground on the car
    body (negative pole). Check the battery voltage before installing it into a camping
    vehicle, bus, or truck.
    To avoid short circuits, the battery has to be disconnected before the installation.
    Read the guidelines in this handbook for the connection of the power supply and
    other options.
    Secure the installed cables with insulating tape, cable ties, or cable clamps. To
    protect the cables from damage, use insulating tape when guiding them past metal
    components. Place and secure all cables in such a manner that they are not in the
    vicinity of movable parts, such as e.g. the parking brake, gas/brake/coupling pedals,
    handle bars and seat tracks.
    Don’t place any cables in the vicinity of heat sources (e.g. near the heater ventilation),
    since the insulation of the cables might get damaged and result in short circuits.
    Don’t short circuit any cables. This can result in damages to the vehicle and device.
    Never establish a power supply to other devices by removing the insulation of the
    device’s power supply and connecting an additional cable. Otherwise, the maximum
    power rating of the cable will be exceeded and there will be a danger of overheating.
    If you have to replace the fuse, only use an identical one with the same rating.
    The connected speakers have to be high-performance speakers with a minimum
    output of 40 W and an impedance ranging from 4 to 8 ohm. If you connect speakers
    with other output or impedance ratings, the speakers may burn, smoke, or sustain
    other kinds of damage.
    When the device is turned on, a control signal adjoins the blue cable of the
    connection A5 (ISO plug A). You can connect this to the relay of the extendable
    vehicle antenna (max. 100 mA, 12 V=). If your vehicle has a wire antenna inside the
    windshield, connect the blue cable A5 (ISO plug A) to the pre-amplifier of the
    antenna.
    If an external audio amplifier is connected to the device, the blue cable of connection
    A5 (ISO plug A) may not be connected to the power supply of the amplifier. Likewise,
    you may not connect it to the power supply of an active car antenna. This poses a
    risk of short circuits and malfunctions.
    Insulate unused connection cables with insulating tape. The same applies to unused
    speaker cables. Otherwise there is a risk of short circuits.
    Dirt or condensed moisture on the lens of the CD/DVD drive may impede and even
    prevent the playback of data carriers.
    In general, the playback of self-burned data carriers is possible, but it depends on the
    used software and the settings made with it, so that there may be problems during
    playback in individual cases. You can receive further information from the
    manufacturer of your software.
    Additional CD data carriers can be played back just like audio CDs. It’s possible that
    CD-R/CD-RW data carriers can’t be played back correctly if they were recorded by a
    device other than an audio CD recorder.
    In addition, it may be the case that a data carrier (CD-R/CD-RW) recorded with an
    audio CD recorder can’t be played back due to the conditional features, irregular
    formats, or soiling of the data carriers.
    The information recorded on the data carrier (ID3TAG) is displayed by this device.
    After inserting a CD-RW data carrier, it takes a little longer for the playback to begin
    than with regular CD or CD-R data carriers. Also read the guidelines on the sleeves
    of the CD-R/CD-RW data carriers before you insert them.

  • Page 5

    DVD7200BT

    ENGLISH

    TABLE OF CONTENTS
    Important safety instructions .................................................................................................. 2
    Scope of delivery ................................................................................................................... 4
    Operating unit........................................................................................................................ 5
    Connections DVD7200BT ..................................................................................................... 7
    Installing the device ............................................................................................................... 9
    Operation of the monitor .......................................................................................................11
    Swiveling the monitor outward ..........................................................................................11
    Areas sensitive to touch (touch screen) ............................................................................11
    Info Display ..........................................................................................................................13
    Display when the monitor is open .........................................................................................13
    Second playback level (dual zone) ...................................................................................14
    Setup menu ......................................................................................................................14
    Audio menu ......................................................................................................................14
    Video menu ......................................................................................................................15
    RDS menu ........................................................................................................................15
    System menu ...................................................................................................................15
    BASIC OPERATIONS ..........................................................................................................16
    Insertion of the operating unit ...........................................................................................16
    Removal of the operating unit (theft protection) ................................................................16
    Turning on/off ...................................................................................................................16
    Changing the volume........................................................................................................16
    Muting the speakers .........................................................................................................17
    Selection of the radio station ............................................................................................17
    Selection of the wavelength range ....................................................................................17
    Searching for a radio station with the scanner ..................................................................17
    Manual search for a radio station......................................................................................17
    Storing a station with the station buttons ..........................................................................18
    Storing stations with automatic station search ..................................................................18
    Calling up stored stations .................................................................................................18
    Checking stored stations ..................................................................................................18
    LOC function ....................................................................................................................18
    STMO function .................................................................................................................19
    RDS .................................................................................................................................19
    Traffic announcements (“TA“, traffic program, ”TP“) .........................................................19
    Alternative frequencies (“AF“) ...........................................................................................19
    Radio reception conditions ...............................................................................................20
    Enhanced Other Networks (EON).....................................................................................20
    Regional programs (“REG“) ..............................................................................................20
    CD/DVD mode..................................................................................................................20
    Selecting a CD/DVD as the program source .....................................................................20
    Insert / remove DVD/CD ...................................................................................................21
    Playback / pause / stop ....................................................................................................21
    Selecting or repeating tracks ............................................................................................21
    Fast forward and rewind ...................................................................................................21
    Repeating tracks (Repeat) ................................................................................................21
    Intro ..................................................................................................................................21
    Playing tracks in random sequence (Random) .................................................................22
    Inserting / removing SD/MMC ...........................................................................................22
    Selecting SD/MMC as a program source ..........................................................................22
    Playing back MP3/WMA/OGG files ...................................................................................22
    Displaying images ............................................................................................................23
    Slide show ........................................................................................................................23

    Page 2 of 44 pages

  • Page 6

    DVD7200BT

    ENGLISH

    Rotating an image ............................................................................................................23
    Zoom ................................................................................................................................23
    Thumbnail view ................................................................................................................23
    AUX IN .............................................................................................................................24
    Menu settings level 1 ........................................................................................................24
    Changing the bass settings (BASS) ..................................................................................24
    Changing the treble settings (TREBLE) ............................................................................24
    Changing the volume ratio (BALANCE) ............................................................................24
    Changing the volume distribution (FADER) ......................................................................25
    Menu settings level 2 ........................................................................................................25
    LOC function to set the station search ..............................................................................25
    LOUD function for the tone setting – loudness..................................................................26
    ST – MO function to switch between stereo and mono playback ......................................26
    CT function to set the time of day .....................................................................................26
    TAVOL function to set the volume for traffic announcements ...........................................26
    EON for the automatic station switch for traffic announcements .......................................27
    D/Z for the settings of the second playback level (DUAL ZONE) ......................................27
    DVD device settings .............................................................................................................28
    General settings ...............................................................................................................28
    Audio settings ...................................................................................................................29
    Video settings ...................................................................................................................30
    Preferred settings .............................................................................................................30
    Password settings ............................................................................................................31
    Exiting the settings ...........................................................................................................32
    Factory default settings (“RESET“) ...................................................................................32
    Remote Controls ..................................................................................................................33
    Remote control (normal) ...................................................................................................33
    Remote control (Dual Zone) .............................................................................................33
    Changing the battery ........................................................................................................34
    RDS OPERATION AND DESCRIPTION ..............................................................................35
    BLUETOOTH Operation .......................................................................................................37
    Pairing ..........................................................................................................................37
    Making a call.................................................................................................................37
    Hang up / Reject ...........................................................................................................37
    Receiving calls..............................................................................................................37
    Voice transfer from unit to phone and vice versa ..........................................................38
    Telephone book pairing ................................................................................................38
    Making a call from the phonebook ................................................................................38
    A2DP (Advanced Audio Distribution Profile) .................................................................39
    TECHNICAL SPECIFICATIONS ..........................................................................................40
    GENERAL ........................................................................................................................40
    FM / MW RADIO..............................................................................................................40
    DVD PLAYER...................................................................................................................40
    AUX IN .............................................................................................................................40
    VIDEO ..............................................................................................................................40
    TFT MONITOR .................................................................................................................40
    ENVIRONMENT ...............................................................................................................40
    NAVIGATION CONNECTION ..............................................................................................41
    GPS antenna installation ..................................................................................................41
    GPS main menu ...............................................................................................................42
    CALIBRATION of the touch screen. .................................................................................42
    SERVICE AND WARRANTY ................................................................................................43

    Page 3 of 44 pages

  • Page 7

    DVD7200BT

    ENGLISH

    Scope of delivery
    Note: The design and technical data are subject to change without any notification.
    Illustrations are not true to scale.

    1x external Microphone

    DVD7200BT (open and closed)

    1x installation frame
    2x Disassembly key
    + Installation material
    1x UNIT IR-Remote
    Control and 1x Dual
    Zone
    IR-Remote
    control. Both with one
    CR2025 3Volt cell
    battery.

    1x front panel protection sleeve

    This User Manual.

    1x ISO cable.

    Page 4 of 44 pages

  • Page 8

    DVD7200BT

    ENGLISH

    Operating unit

    (A)

    (B)

    (C)

    A) Front view (closed)
    B) Front view (monitor open)
    C) Front view (with detached operating unit)

    Page 5 of 44 pages

  • Page 9

    DVD7200BT
    (1)

    (2)
    (3)
    (4)
    (5)
    (6)
    (7)
    (8)

    (9)

    (10)

    (11)
    (12)
    (13)
    (14)
    (15)
    (16)
    (17)
    (18)
    (19)
    (20)
    (21)
    (22)
    (23)
    (24)
    (25)
    (26)
    (27)
    (28)
    (29)
    (30)
    (31)
    (32)
    (33)

    ENGLISH

    Volume control dial (turned)
    a. Settings dial for menu level 1 – VOL, BAS, TRE, BAL, FAD (if pressed for less
    than two seconds)
    b. Settings dial for menu level 2 - LOC - LOUD – STEREO/MONO - TIME TAVOL - EON – DUAL ZONE - (if pressed for more than two seconds)
    c. LOC is only available in radio mode
    TP button to turn the traffic alert function on/off
    a. Button to activate the loudness function (pressed longer than three seconds)
    MODE button to select sources between radio, CD/DVD (if inserted), memory card (if
    inserted), rear view camera and AUX In / In BT MODE: Hang up or reject call.
    Station selection button 1 (radio mode)
    a. Start /pause button (data carrier mode)
    Station selection button 2 (radio mode)
    a. Previous track (data carrier mode)
    Station selection button 3 (radio mode)
    a. Next track (data carrier mode)
    Button to turn the device on / off (Short press while unit is off or long press while unit
    is on) or while unit is on with short press: MUTE.
    Station selection button 4 (radio mode)
    a. Repeat track (data carrier mode)
    b. if pressed longer: Quick rewind (data carrier mode)
    Station selection button 5 (radio mode)
    a. Scan track “intro” (data carrier mode)
    b. if pressed longer: Fast forward (data carrier mode)
    Station selection button 6 (radio mode)
    a. Random playback (data carrier mode)
    b. if pressed longer: Stop button (data carrier mode)
    Accept call / Pairing
    CD/DVD eject button
    Infrared sensor for the remote controls
    5-Way multifunction button for the menu navigation to the right, left, up, down, and
    confirm (pressed)
    BAND – Button to switch the frequency band as well as the button memory FM1 FM3, MW1 and MW2
    OPEN – Button to open and close the 7” monitor
    P.SCAN – Button for the automatic station scanning (short press) and the automatic
    station storage (long press)
    CD / DVD insertion slot
    INFO Display
    PTY button to select the program style (e.g. jazz, pop, news, etc.)
    AF/REG button: Alternative frequency ON/OFF and REG ON/OFF (if pressed longer)
    Button to remove the operating unit
    7” TFT monitor (touch sensitive)
    BAND – Button to switch the frequency band as well as the button memory FM1 FM3, MW1 and MW2
    Button to change the display information (only in data carrier mode)
    Button to activate the monitor menu for the playback source and device settings
    Button to display the DVD playback menu (only in CD/DVD mode)
    Button to activate the monitor menu for the DVD device settings
    Button to change the distance of the monitor to the installation slot
    Button to set the slant of the monitor (TILT)
    Contacts for the operating unit PLEASE DON’T TOUCH!!
    Reset button to restore factory default settings. Note: When the factory settings are
    restored, the clock and the stored radio stations will also be reset or erased
    SD/MMC card slot

    Page 6 of 44 pages

  • Page 10

    DVD7200BT

    ENGLISH

    Connections DVD7200BT

    1) Antenna Input (75 Ohm)
    2) DVB-T TV (optional)
    3) AUX Input L+R (brown)
    4) Rear Output L+R (Gray)
    5) Camera Input (Black)
    6) Rear Video Output (Black)
    7) Video Input (Black)
    8) Cable connector
    9) Optical 5.1CH output
    Driver
    Safety wire
    (Brown), has to be connected to
    the parking brake or other
    suitable components of the
    vehicle in such a way that the
    video playback of the device is
    interrupted for the driver while
    the vehicle is in motion. Please
    consider that your insurance
    coverage may be restricted or
    exempted otherwise. Please
    consult a specialist in your area
    if you have any questions about
    the connections.
    11) Subwoofer Output (Black)
    12) Rear Line Output (Gray)
    13) Front Line Output (Brown)
    14) ISO connector
    15) External Microphone
    16) NAVIGATION CONNECTOR

    RCA
    CONNECTORS

    Left = White
    Right = Red
    Others = Yellow

    ISO CONNECTOR

    10)

    Note
    on
    ISO-A Connector:
    Depending on the manufacturer, the
    contacts on your vehicle connection
    may be assigned differently. This is
    not a defect of the device but
    caused by a deviating connector pin
    assignment by the manufacturer of
    your vehicle. To provide a
    connection that conforms to this
    device,
    please
    purchase
    an
    appropriate adapter cable from a
    specialized dealer if required.
    Please consult a specialist in your
    area if you have any questions
    about the connections..

    ISO-A
    A2

    A4

    ORANGE Connection to the
    reverse light to switch on the
    rear view camera when the
    reverse gear is put in.
    YELLOW (B+). Connection for
    +12V
    operational
    voltage
    (diameter at least 2.5 mm²) to
    permanent plus of the vehicle.

    A5

    BLUE To system control
    terminal of an external amplifier
    or Automatic Antenna (max.
    100mA / 12Vdc).

    A7

    RED ACC (+).Connection for
    +12V trigger voltage. Connect
    to ignition key of the vehicle. If
    contacts A4 and A7 are
    switched, the device will “forget”
    the stored stations after the
    ignition is turned off.

    A8

    GND. ( - / Ground) Attach the
    connection for the ground
    (diameter at least 2.5 mm) to
    the ground of the vehicle.

    Page 7 of 44 pages

    ISO-B
    FRONT SPEAKER
    B3
    B4
    B5
    B6

    Right +
    Right –
    Left +
    Left –

    (Gray)
    (Gray/Black)
    (White)
    (White/Black)

    REAR SPEAKER
    B1
    B2
    B7
    B8

    Right +
    Right –
    Left +
    Left –

    (Violet)
    (Violet/Black)
    (Green)
    (Green/Black)

  • Page 11

    DVD7200BT

    ENGLISH

    Note:
    -

    -

    Only use groundless loudspeakers.
    Use only loudspeakers of minimal 40Watt, using fewer watts may result in damaging your
    loudspeakers at higher volumes.
    Use 4~8 Ÿ (Ohm impedance) loudspeakers only; using higher or lesser impedance may
    damage the unit.
    Do not use 3-cable loudspeakers and do not connect the loudspeakers minus to the car body
    (GND). The DVD7200BT is using a BTL circuit and each loudspeaker must be connected with
    insulated cables according the diagram.
    Loudspeaker cables and/or optional external power amplifiers must always be about 30cm
    away from the antenna and/or antenna extension parts.

    Connect the speakers according the following diagram, incorrect connections will damage
    the unit or your loudspeakers
    Correct connection
    Left front - Right front | Left rear - Right rear

    Incorrect connections

    Page 8 of 44 pages

  • Page 12

    DVD7200BT

    ENGLISH

    Installing the device
    Note:
    Please observe the following safety instructions for the connection of the device:
    Read the entire installation section before connecting the device.
    Disconnect the negative pole of the vehicle battery for the duration of the installation.
    Observe the safety instructions by the vehicle manufacturer during this task.
    If you need to drill holes for the installation, make sure that no parts of the vehicle are
    damaged.
    The cross section of the positive and negative cable may not be less than 2.5 mm².
    Do not connect any of the vehicle’s plugs and cables to the radio unless you have the
    appropriate specialized knowledge of this process!
    - Only use the supplied cable to connect the device.
    - Depending on the build of your vehicle, the installation may deviate from this
    description.
    - We do not assume any liability for damages caused by faulty installations or
    connections, nor any subsequent damages.
    - We recommend that you have the device installed by a specialized company. Then
    you will have created the prerequisites for a problem-free functioning of the device. If
    at any point during the installation you are unsure that you can correctly connect the
    device by yourself, contact a specialist. A faulty installation may cause damages to
    the device and the vehicle electronics.

    Fig. B.

    Fig. A.

    Fig. C.

    1) Remove the installation frame from the device with the aid of the disassembly key, by
    sliding the disassembly keys into the provided openings on the right and left side of
    the device, as described in Fig A.
    2) Make sure that the protrusion on the disassembly key points away from the device
    during the insertion (Fig C + Fig. B.) Afterwards, the frame can be slid down over the
    device towards the rear.
    3) Now slide the installation frame into the installation slot provided for the car radio.
    4) Now attach the installation frame by bending the installation brackets towards the
    outside with a screwdriver. The frame is properly installed when it can no longer be
    pulled out, yet also keeps from sliding into the installation slot.
    5) Now connect the cable set and the antenna to the vehicle’s electronics corresponding
    to page 6.
    6) Insert the device into the installation frame until the stop.
    7) The device then audibly snaps into the frame. Attach the front frame and then insert
    the operating unit.

    Page 9 of 44 pages

  • Page 13

    DVD7200BT

    ENGLISH

    8) The device is distinguished by a high degree of output. During operation, this results
    in a strong heat generation. Therefore no cables or other parts may adjoin the device.
    If their insulation melts, there is the risk of a short circuit or fire.
    9) REMOVING: Turn off the device. Remove the operating unit and place it into the
    case. Clamp off the negative pole of the vehicle battery for the duration of the
    disassembly. First remove the front frame of the device by inserting a flat object (e.g.
    the back of the disassembly key) between the device and the panel to the right and
    left of the short side of the frame and carefully levering the panel out towards the
    front. Then insert the two disassembly keys into the openings on both sides of the
    front of the device and slide these until the stop. Make sure that the protrusion on the
    disassembly key points away from the device during the insertion. Slowly and
    carefully pull out the device. Remove the cable and antenna from the device.
    10) Make sure that no vehicle cable can cause a short circuit after the device has been
    unplugged.

    Page 10 of 44 pages

  • Page 14

    DVD7200BT

    ENGLISH

    Operation of the monitor
    Open the monitor by briefly pressing the “OPEN” button. Now the monitor is opened
    automatically and fixed in the flipped-open position. The monitor can be closed again by
    pressing the “OPEN” button again. If the monitor doesn’t close as a result, it may not be in
    the correct position. Then there will be the error message “ERROR – MONITOR NOT
    CENTERED!!”
    Note:
    Before beginning to drive, please familiarize yourself sufficiently with the device and avoid
    longer entries during the drive for your own safety!

    Swiveling the monitor outward
    To better read and operate the screen, it’s possible to swivel the monitor of the device by
    about 30° to the right and left. For this, first open the monitor with the “OPEN” button as
    described above. Then you can swivel the monitor by pulling it towards you carefully from the
    lower right or left edge of the screen. Never use force during the process, otherwise you
    might damage the device. To swivel the monitor back, just press it back into the original
    position.
    Areas sensitive to touch (touch screen)
    The screen has features that are sensitive to the touch (touch screen). This makes it possible
    to control many functions by touching the screen. In an open position there are always two
    menus available. First the main menu and, in addition, the menu for the second playback
    level (dual zone).

    The two areas indicated above are not visible on the screen. The image merely serves for a
    clearer visualization. But if you press a finger or an object against the indicated areas, the
    corresponding submenu will open. The menus and their functions are addressed in the
    following chapter.

    Page 11 of 44 pages

  • Page 15

    DVD7200BT

    ENGLISH

    Note:
    Please only touch the screen with very light pressure and never with sharp objects.
    Otherwise it might get scratched and damaged. When the monitor is being opened or closed,
    no sound will be produced during this process. This is not a malfunction of the device.
    For the playback of audio, video or image data, there is also another, non-visible menu
    available. When touching the right edge of the screen in the area of the marked surface, the
    playback will jump to the next track. When touching the left edge of the screen in the area of
    the marked surface, the playback will jump to the previous track. At the lower edge of the
    screen, you will reach an additional menu by means of the marked area.

    You can reach the menu pictured in below by touching the field that is indicated as “MENU“
    in the picture above. Then the adjoining menu is activated and makes the functions available
    according to their symbols. Through “EJECT“ you can eject the CD/DVD data carrier.
    Through “EXIT“ you will exit the menu and return to the display that was there prior to the
    activation of the menu. The menu automatically fades out ten seconds after the last entry.

    Page 12 of 44 pages

  • Page 16

    DVD7200BT

    ENGLISH

    Info Display
    Info Display when the monitor is closed Display (entire view) when the monitor is closed

    MUTE
    HIT RADIO
    PTY

    EON

    LOC
    DISC
    RDM
    AF
    STOP

    The loudspeakers have been
    muted
    (Example): RDS program
    name
    A broadcast program with
    program type information is
    being received
    EON
    (Enhanced
    Other
    Networks) data are being
    received
    The selection of local radio
    stations has been activated.
    CD/DVD has been inserted

    LOUD
    100.60
    TP
    2
    ST
    INT

    Tracks are played back in
    TA
    random sequence (Random)
    Alternative frequency has
    RPT
    been activated
    The playback has finished.
    00:28

    The LOUDNESS function
    has been activated
    Frequency in the FM range
    A broadcast program with
    traffic information is being
    received
    Preset location of the
    selected station on the
    station buttons
    An FM Stereo program is
    being received
    Beginnings of tracks are
    being played (intro)
    Readiness for traffic alerts
    has been activated
    A CD track is being repeated
    (Repeat)
    Duration of the current track

    Display when the monitor is open

    To open the monitor, please press button “OPEN”. To call up the monitor menu,
    please press the “OSD button”. When the monitor is open, the following setting
    options and functions are available: (The function “TV MODE” is not available.)
    MENU
    ENTRY
    RADIO MODE

    MEDIA MODE

    NAVIGATION
    BLUETOOTH
    DUAL
    SETUP

    FUNCTION
    Switches to the radio mode and
    reproduces the recently played station.
    DVD MODE: Switches to the DVD mode
    and starts the playback of the inserted
    CD/DVD data carrier.
    SD CARD: Switches to the data carrier and
    begins the playback of the files it contains.
    CAMERA: Switches to a connected
    camera and shows the image recorded by
    the camera
    AUX IN: Change mode to AUX Input.
    TV Mode: (optional)
    GPS NAVIGATION
    Switches to the Bluetooth menu when a
    telephone is paired and connected.
    Switches to the DUAL ZONE submenu.
    Switches to the menu for the device
    settings.

    Page 13 of 44 pages

  • Page 17

    DVD7200BT

    ENGLISH

    Second playback level (dual zone)

    The device has a second playback level (dual zone). This makes it possible to
    address a second playback medium. For example: listening to the radio on the front
    seats and watching a DVD on the back seats. Several combination options are
    available here.
    MENU
    ENTRY
    DVD MODE
    SD CARD
    TV
    AUX IN
    DUAL OFF

    Setup menu
    MENU
    ENTRY
    SOUND
    DISPLAY
    SYSTEM
    RDS
    TV
    CALIBRATION

    Audio menu
    MENU
    ENTRY
    BASS/TREBLE
    BALANCE
    FADER
    S.WOOFER

    S.VOLUME

    TEL VOL

    FUNCTION
    Starts the playback of the inserted CD/DVD
    data carrier.
    Starts the playback of the inserted
    SD/MMC data carrier.
    The TV function is optional for the DVB-T
    tuner box
    Switches to the video and audio input of
    the device. This makes it possible to
    integrate external video and audio sources.
    Ends the second playback level.

    FUNCTION
    Switches to the submenu for audio
    settings
    Switches to the submenu for video settings
    Switches to the submenu for system
    settings
    Switches to the submenu for RDS settings
    The TV function is on a grey surface and
    not available.
    Switches to the submenu for the
    orientation of the touch screen

    FUNCTION
    Setting bass/treble levels from -7 to +7
    Setting the left and right speaker ratio
    from L-8 to R-8.
    Setting the playback ratio between the
    front and rear from F-8 to R-8.
    Turning the subwoofer on and off
    Setting the initial volume level. The
    maximum volume level of the device is at
    45. The initial volume level can be set
    between 0 - 45. The initial volume level is
    a function that protects from hearing
    damage. To protect your health, leave the
    initial volume at a low level and, if
    necessary, adjust the playback volume
    according to the external conditions.
    Setting the initial Telephone volume level.

    Page 14 of 44 pages

  • Page 18

    DVD7200BT
    Video menu
    MENU
    ENTRY
    BRIGHT
    CONTRAST
    COLOR
    SHARP
    SCREEN

    RDS menu
    MENU
    ENTRY
    AF
    REGION
    TP
    EON
    PTY
    TA VOL

    System menu
    MENU
    ENTRY
    BEEP

    ENGLISH
    FUNCTION

    Setting the screen brightness from 0 to 40
    Setting the screen contrast levels from 0
    to 40
    Setting the screen color values from 0 to
    40
    Setting the screen playback sharpness
    from 0 to 6
    Setting the side ratio during the playback.
    The side ratios 16:9 and 4:3 are available.

    FUNCTION
    Turning the alternative frequency function
    on and off.
    Turning the function for regional programs
    on and off.
    Turning the traffic alert function on and off.
    Turning the EON function on and off.
    Turning the PTY function on and off.
    Setting the volume of the traffic alerts.
    The volume can be selected between 0
    and 45.

    FUNCTION
    Turning the button sounds on and off.

    The TILT function makes it possible to set
    the position of the monitor. With AUTO, the
    monitor is retracted when the device is
    TILT
    turned off. With MANUAL, the monitor
    remains open when the device is turned off.
    But it can be closed and opened again at
    any time by pressing the “OPEN” button.
    This function lets you adjust the tilt of the
    monitor according to your personal
    TILT RANGE
    preferences. Different setting options are
    available.
    The IN/OUT FIX function allows you to vary
    the distance of the monitor towards the
    front or the rear so that it can be adjusted
    IN/OUT FIX
    according to your personal preferences.
    NONE lets you freely choose the position.
    With FIXED, you lock the monitor into a
    particular position.
    A function to set the time of day.
    TIME SET
    GPS DUAL
    NAVIGATION sound on/off while in other
    SOUND
    mode (Radio/DVD/SD/AUX-in)

    Page 15 of 44 pages

  • Page 19

    DVD7200BT

    ENGLISH

    BASIC OPERATIONS
    Insertion of the operating unit
    In order to activate the car radio, you first have to insert the operating unit. First slide the
    operating unit in a slightly tilted position from the left into the right holder and then press it
    against the casing until it audibly snaps into place. Now you can turn on the device. If the
    device was turned on when the operating unit was removed, it will automatically turn on with
    the last setting (radio, CD, SD/MMC, AUX IN) as soon as the operating unit is inserted again.

    Removal of the operating unit (theft protection)
    In order to remove the operating unit and thus protect your car radio from theft, turn off the
    device with the on/off button. Now press the REL button. The operating unit then releases
    from the device and you can detach it towards the front and left. Place the operating unit into
    the provided case and take it with you when you leave the car.
    Turning on/off
    To turn on the device, briefly press the on/off button, or any other button, on the operating
    unit. To turn the device off, long press the on/off button again. The device will then turn off. If
    the device is activated after the ignition has been started, it will automatically turn on and off
    with the ignition during subsequent operation.
    Caution! When the radio is turned on, an automatic antenna that may be installed on the
    vehicle will also be extended. Before driving into a car wash, you should therefore always
    turn off the device in order to avoid damages to the antenna as well as the vehicle.
    Changing the volume
    The volume of the device can be changed with the round control dial. The current volume of
    the device will be indicated on the display in the process. The volume scale ranges from 0 –
    45. When the car radio is turned off, the volume is only stored if it falls below the level of the
    “S.VOLUME” setting. Any volume levels exceeding this are reduced to protect hearing. The
    volume for the reactivation can be set in the system menu under the “S.VOLUME” function.
    Note:
    - Don’t use the car radio at an excessive volume. Otherwise there is the risk that you
    will permanently damage your hearing.
    - Please consider that while using the device you should still be in the position of
    perceiving your surroundings (warning signals, sirens, etc.).
    - Please only perform lengthy changes of the device settings while the vehicle is
    parked. Otherwise your concentration might be affected by the changes.

    Page 16 of 44 pages

  • Page 20

    DVD7200BT

    ENGLISH

    Muting the speakers
    To mute the connected speakers, briefly press the “MUTE” button. “MUTE” will appear on the
    display. To return to the original volume, press the “MUTE” button again briefly or turn the
    volume control dial. The message “MUTE” will turn off and the volume will be at the same
    level as before it was muted. The MUTE setting also affects the LINE outputs and disrupts
    these until the function is deactivated again.
    Selection of the radio station
    Turn on the DVD7200BT CD/DVD car radio with the on/off button. If the device was turned
    off while it was in RADIO mode, the last selected station will be heard. If the device is set to
    an operation with one of the different data carriers, please press the “MODE” button until you
    get to the radio function.

    Radio Display with open monitor

    Radio display with open monitor with
    activated Dual Zone

    Selection of the wavelength range
    FM (UKW) range: To select the FM range, briefly press the “BAND” button repeatedly until
    the desired range "F1“, “F2“, or “F3“ (with a closed monitor) or "FM 1“, “FM 2“, or “FM 3“ (with
    an open monitor) appear on the display along with the current frequency.
    MW range: To select the MW range, briefly press the “BAND” button repeatedly until “M1” or
    “M2” (with a closed monitor) or “MW 1” or “MW 2” (with an open monitor) appear on the
    display along with the current frequency.
    Note: After selecting a range, the station last selected in this range will be heard. When the
    monitor is open, the “BAND” button on the screen is also available for the selection of the
    wavelength range.
    Searching for a radio station with the scanner
    To set the stations, select the desired wave band with the “BAND” button. In order to begin
    searching in the desired direction, briefly press the five-way multifunction button. Press the
    button towards the left to diminish the search frequency or to the right to increase the search
    frequency. The scanner will stop at the next available station. When the monitor is open, the
    buttons  and  on the on-screen keyboard are also available to change the frequency.
    Manual search for a radio station
    In order to select a station manually, press the five-way multifunction button for about three
    seconds towards the right or left. The display will indicate “MANUAL”. Now press the fiveway multifunction button towards the right to increase the frequency, or to the left to diminish
    the frequency until the desired frequency is indicated on the display. The frequency will
    change in 50kHz increments in the FM range. If there is no entry for about seven seconds,
    the device will switch back to automatic station search. The display will indicate “AUTO”.

    Page 17 of 44 pages

  • Page 21

    DVD7200BT

    ENGLISH

    When the monitor is open, the buttons  and  on the on-screen keyboard are also
    available to change the frequency. Here you also have the option to search manually, by
    pressing one of the buttons  and  for three seconds. MANUAL will be indicated in the
    corresponding field. If there is no entry for about seven seconds, the device will switch back
    to automatic station search. The corresponding field on the screen will indicate “AUTO”
    again.
    Storing a station with the station buttons
    With the station buttons “1”, “2”, “3”, “4”, “5”, and “6” you can preset six programming spaces
    each on each level of the wave band (e.g. “FM 1“, “FM 2”, or “FM 3”). To store the station,
    select the corresponding station with the station search or manually. Press one of the buttons
    “1”, “2”, “3”, "4", "5" or "6" until the radio sound is briefly muted in order to store the station.
    Now the station is stored at the station button you selected. When the monitor is open,
    please keep your finger on the corresponding station field until the playback is briefly
    interrupted. Now the station is stored at the corresponding position.
    Storing stations with automatic station search
    The automatic station search scans for the strongest available stations and stores these
    under the station selection buttons “1” - “6”. In order to start the search, press the “P.SCAN”
    button and keep it pressed for more than two seconds. Now the scanner allocates all station
    positions at the current level of the selected wave band as long as enough stations with
    sufficient reception quality are available. After the scanning has ended, the stored stations
    are automatically matched up with their station names and the station stored at the station
    position “1” can be heard. Now the device will briefly play all stations in sequence and then
    stop at the station under the station button “1”. When the monitor is open, the PSCN field is
    available to you for this function.
    Calling up stored stations
    In order to access the stored stations, select the desired wave range with the “BAND” button,
    e.g. “FM 1”. Press one of the six station buttons and you will hear the station stored there.
    The corresponding applies when the monitor is open.
    Checking stored stations
    For this function, the stations stored under the station buttons of a particular wave length are
    scanned for about five seconds. In order to begin checking, briefly press the “P.SCAN”
    button. The station positions “1” - “6” will begin flashing on the display in sequence and the
    corresponding stations will be scanned. When the monitor is open, the currently scanned
    memory position has a lighted background and PRESET will be indicated on the display. The
    PSCN field will be available to you here as well. To remain at the currently scanned station,
    press the “P.SCAN” button or the PSCN field again. Then the setting will remain at the last
    scanned station. If no entry is made by the end of the complete search, the device will play
    the first station on the corresponding level (e.g. F1 or FM 1).
    LOC function
    The “LOCAL” function is relevant for the station search. Here you can select whether only
    local, strong stations (“ON”) or also weaker, more distant stations (“OFF”) are searched for.
    The “LOC” function prevents a corresponding switch to a stronger station as long as it isn’t
    broadcasting the same program as the one currently being listened to. You can activate the
    function by briefly pressing the screen button “LOC” once. Then the button switches colors
    from grey to white. If the button sounds are turned on, a brief signal tone will follow. This
    function can be turned off again by pressing the screen button "LOC" once more. Then the
    color changes from white to grey again and this may be followed by a signal tone. This
    setting only affects the radio mode and can only be carried out while the radio mode is
    active.

    Page 18 of 44 pages

  • Page 22

    DVD7200BT

    ENGLISH

    STMO function
    The “STMO” function enables you to switch back and forth between mono and stereo
    playback. This is especially useful when the stereo signal of the selected radio station
    doesn’t carry an ideal strength. In order to activate the “STMO” function, please press the
    screen button “STMO” once briefly. Then the color changes from white to grey again and the
    radio signal is briefly interrupted. In order to deactivate the “STMO” function again, please
    press the screen button “STMO” briefly once more. Then the color of the button changes
    from white to grey again and the radio signal is briefly interrupted.
    RDS
    RDS is an information system whose signals are additionally broadcast by most FM stations.
    With RDS programs, the name of the program appears as an abbreviation on the display.
    Further information, such as frequency, time and program type (PTY) can be faded in. An
    RDS program will be broadcast by several senders on different frequencies (alternative
    frequencies). If an RDS program has been selected, the device automatically switches to the
    alternative frequency that can be received most clearly, as long as that is available and the
    AF function has been turned on. You can read the RDS information when the monitor is
    open. The time, RDS station name and frequency will appear on the display.
    Traffic announcements (“TA“, traffic program, ”TP“)
    To activate the traffic announcement program, please press the “TP” button briefly. The
    message “TA” will appear on the display and the readiness for announcements is turned on.
    To deactivate the traffic announcements, press the “TP” button again. The message “TA”
    disappears and the readiness for announcements has been switched off. When the monitor
    is open, the display will jump to the RDS submenu and switch the function on or off. If there
    is no entry for approx. ten seconds, the device returns to the radio display and store the
    changes that were made.
    Note:
    - If the selected station is not a traffic broadcast station, the device automatically starts
    to scan for the next traffic broadcast station.
    - If “TP” is turned on, the CD/DVD, SD-MMC, USB and AUX IN operation is interrupted
    for a traffic announcement and will be continued afterwards. For the duration of the
    traffic alert, "TP” will appear on the display. During AUX IN operation, the current
    track will not stop but continue playing. To stop the device connected via AUX IN,
    please consult the manual of the respective manufacturer of the device.
    - If you only want to hear traffic announcements, turn on the announcement function
    with the “TP” button and turn the volume to “VOL 0” with the volume control dial or
    use the MUTE function. The device will automatically regulate a volume increase for
    traffic announcements.
    - The TA volume can be individually adjusted under the volume item “TA VOL”.
    Alternative frequencies (“AF“)
    To activate the “AF” function, briefly press the “AF/REG” button. The message “AF” appears
    and the function is turned on. To turn off the “AF” function, briefly press the “AF/REG” button.
    The message “AF” disappears and the function is deactivated.
    Note:
    - The “AF” function is only displayed for broadcast stations that broadcast an “AF”
    signal. The “AF” message flashes when the “AF” function is activated but no “AF”
    signal is available.
    - If an RDS (radio data system) station is being received that is broadcast by several
    broadcast stations with different frequencies, the device automatically switches to the
    frequency that can be received most clearly.

    Page 19 of 44 pages

  • Page 23

    DVD7200BT
    -

    ENGLISH

    The “AF” function is activated when the device is shipped.
    In an area with bad reception, attempts to change between alternative frequencies
    can be heard as disruptive pauses. In such an event, the “AF” function can be turned
    off.

    Radio reception conditions
    In the FM wave band, there can be changes in the reception conditions during the drive.
    Mountains, buildings or bridges can diminish reception. This applies especially if the distance
    to the station is large.
    Enhanced Other Networks (EON)
    The “EON” function is an additional RDS service. If the current program doesn’t offer any
    traffic announcements, EON automatically switches to the traffic announcements on another
    program. After the end of the announcement, the device switches back to the previously
    heard station. The readiness for traffic announcements “TA” has to be activated for this. To
    turn the EON function on or off, please switch to the RDS menu.
    Regional programs (“REG“)
    Some radio stations divide their programs into regional programs with different content at
    specific times. If the reception is getting worse, the “REG” function prevents the car radio
    from changing to alternative frequencies that have different program contents. To turn the
    “REG” function on or off, please keep the “AF/REG” button pressed until "REG-ON" or "REGOFF" appears in the display.
    CD/DVD mode
    The DVD7200BT supports the formats DVD, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-R
    DL, DVD+R DL, CD, CD-R, CD-RW, VCD, SVCD, MP3, WMA, OGG Vorbis and JPG image
    CD. The minimum bitrates of WMA and MP3 files are at 32 kbps and for OGG files at 45
    kbps. The maximum bitrates of WMA files is at 192 kbps, MP3 files at 320 kbps, and OGG
    files at 500 kbps.
    Note:
    - Conditional on the quality differences of the media as well the characteristics of the
    recording, it can happen that some individually recorded CDs and DVDs are
    incapable of being read. Such events do not constitute a malfunction of the device.
    - Audio CDs (CD-R and CD-RW) that are recorded individually have to be finalized at
    the end of the burning process.
    - Note that the file names of the audio tracks have to correspond to the ISO-9660
    standard. During the playback of MP3 CDs, individual tracks can be skipped or not
    played back correctly. This can be due to the respective disc configuration, the
    decoder software, or the hardware that was used for the recording.
    - Copy-protected CDs do not correspond to the specifications of audio CDs (CD-DA),
    don’t carry the respective logo, and can therefore cause playback errors.
    - If a selected function is unavailable, a hand 1 symbol will appear in the upper left of
    the display.
    Selecting a CD/DVD as the program source
    To play a CD/DVD, turn on the device with the on/off button. If the device was turned off
    during CD/DVD operation, the playback begins at the track heard before turning off the
    device. If the device is set to another program source, press the “MODE” button until “DVD”
    appears in the display. The display will indicate the message “LOADING”. When the monitor
    is open, the screen menu is also available for the selection of the program source. The
    program source “DVD” can only be selected through the “MODE” button if there is a CD or
    DVD in the insertion slot.

    Page 20 of 44 pages

  • Page 24

    DVD7200BT

    ENGLISH

    Insert / remove DVD/CD
    Before inserting a CD/DVD, make sure that no data carrier has already been inserted by
    pressing the “EJ” button. To insert the CD/DVD, slide it into the insertion slot with the printed
    side up. It will automatically be drawn inside. The message “LOADING” will be indicated on
    the display. Then the message “01" will appear, followed by the time display of the track,
    which thus shows that the first track on the data carrier is now being played back. To eject
    the CD/DVD, press the “EJ” button again and remove the ejected data carrier. When the
    monitor is open, the screen menu is also available to you for the ejection of the data carrier.
    Caution:
    - Only customary CD/DVD formats may be inserted into the insertion slot (Ø 12cm).
    - Make sure that no foreign objects enter the insertion slot.
    - Never use force when inserting the CD/DVD; this could damage the device as well as
    the CD/DVD. Never use force to try to prevent the device from pulling in a CD/DVD. If
    necessary, eject the CD/DVD again. If an ejected data carrier isn’t removed within
    approx. ten seconds, it will be drawn back into the slot to prevent damage to the
    device.
    Playback / pause / stop
    To pause the playback, briefly press the “Pause” button. “PAUSE” will be indicated on the
    display. To continue the playback, press the “PAUSE” button again. To end the playback,
    briefly press the "Stop" button. “STOP” will be indicated on the display. When the monitor is
    open, the screen menu is also available to you for these functions.
    Selecting or repeating tracks
    By briefly pressing the  button, the playback jumps to the next track. If you press the 
    button, the playback returns to the beginning of the current track. If the  button is pressed
    twice, the playback jumps back to the previous track. You can briefly press both the  and
     buttons until the number of the desired track appears on the display. When the monitor is
    open, the screen menu is also available to you for these functions.
    Fast forward and rewind
    To fast forward, briefly press the  button once. Then the playback speed is increased to
    2x. If the button is pressed once more, the speed is doubled again. This can be continued
    up to the maximum advancing speed of 32x. You can stop this process by briefly pressing
    the button once or pressing the  button one more time after the advancing speed of
    32x has been reached. For a quick rewind, use the  button in a corresponding manner. To
    control the process, the increasing or decreasing minute and second amount is indicated on
    the display. When the monitor is open, the screen menu is also available to you for these
    functions.
    Repeating tracks (Repeat)
    To repeat a track, keep the  (RPT) button pressed until “R-ONE“ appears on the display.
    The abbreviation “RPT” is shown and the current track is repeated. To repeat the entire
    folder or CD, press the  (RPT) button again until “R-ALL“ appears on the display. When
    the monitor is open, the messages “SPUR” will appear for “R-ONE” and “ALL” for “R-ALL”.
    To end the function, press the  (RPT) button again until “R-OFF“ appears on the display.
    The abbreviation “RPT” will be turned off and the playback of the tracks will continue
    normally.
    Intro
    To briefly scan the tracks on an audio CD, press the  (INT) button during the playback
    until “INT“ appears on the display. Then all tracks will be scanned for approx. ten seconds.

    Page 21 of 44 pages

  • Page 25

    DVD7200BT

    ENGLISH

    When the monitor is open, the message “INT” will appear. To end the function, press the 
    (INT) button again until the “INT“ message is turned off on the display. The playback
    continues at the point where the last intro was interrupted.
    Playing tracks in random sequence (Random)
    For random playback, press the Ŷ/RDM button during the playback until the abbreviation
    “RDM“ appears on the display. The device begins to play a randomly selected track. If the
    RDM button is pressed during the playback of a track, this track will be played again from the
    beginning. All other tracks will also be played back in random sequence. When the monitor is
    open, the message “RANDOM” will appear. To end the random function, press the Ŷ/RDM
    button again until the abbreviation “RDM“ is turned off. The tracks will now be played back in
    their regular sequence.
    Note:
    If the first track of a multi-session CD contains audio data, only the audio data are played
    back, even if other data formats are recorded.
    Inserting / removing SD/MMC
    To insert an SD/MMC card, please press the REL button on the device. Now the operating
    unit can be removed. Now you can insert a data carrier into the SD/MMC card slot. Please
    insert your SD/MMC card into the card slot with the contacts towards the top and front until it
    audibly snaps into position. SD/MMC cards with a storage capacity of up to 2 GB are
    supported. To remove an SD/MMC card, again press the card to be removed lightly into the
    device until it snaps out. Afterwards you can remove the card from the slot. After removing
    the card, the device automatically switches to CD/DVD as a playback source. If a data carrier
    has been inserted, it will be played back. If no data carrier is inserted, the device will remain
    in the STOP mode of the CD/DVD playback. Never use force when inserting and removing
    an SD/MMC card; this could damage the device as well as the card. Also avoid direct skin
    contact with the contacts on the card to prevent contact problems.
    Note:
    Please consider that you only have approx. 20 seconds to insert an SD/MMC memory card
    into the insertion slot or remove it again. Otherwise the device will assume that the operating
    unit has been removed for theft protection and will turn itself off. If that is the case, just insert
    the operating unit again. Then the device will automatically turn on again.
    Selecting SD/MMC as a program source
    To play back audio tracks from an SD/MMC memory card, press the "MODE” button to select
    “SD/MMC” as the data source. Then the device will read the music tracks that can be
    reproduced from the memory card and begins to play back the first track. The program
    source “SD/MMC” can only be selected through the “MODE” button if there is an SD/MMC
    card in the card reader.
    Playing back MP3/WMA/OGG files
    In addition to audio CDs, the device can also play back music files in the MP3, WMA and
    OGG Vorbis formats. Insert a corresponding data carrier into the device and select this as
    the playback source. To get to the desired folder or the desired track, please use the fiveway multifunction button to navigate. With this button you can navigate upward and
    downward. If you press the button to the right, you will reach the contents of the selected
    folder or additional information about the currently selected title. With images, a thumbnail
    preview will appear. If you press the button to the left, you will return to the higher level
    folder. Press the button normally to play back the selected title.

    Page 22 of 44 pages

  • Page 26

    DVD7200BT

    ENGLISH

    REPEAT FOLDER

    File overview

    Track overview

    If the files stored on the data carrier have been supplied with ID3 tags or comparable tag
    information, these will be indicated in the right half of the window during the playback.
    Displaying images
    This function allows you to display images on the screen. You can use this function for
    CD/DVD data carriers as well as for a SD/MMC memory card. The navigation of this function
    generally functions just as during the playback of MP3, WMA and OGG Vorbis files.
    Slide show
    To display the images in a slide show, change to the corresponding data carrier by pressing
    the “MODE” button. To get to the desired image, please use the five-way multifunction button
    to navigate. With this button you can navigate upward and downward. With images, a
    thumbnail preview will appear. If you press the button to the left, you will return to the higher
    level folder. Press the button regularly to display the image at the full screen size. Now the
    slide show is started.
    Rotating an image
    During the slide show, you have the option of rotating the current image to the right or left by
    pressing the five-way multifunction button.
    Zoom
    The zoom function gives you the option of having the images and films displayed in an
    enlarged or reduced format. To activate the zoom function, press the ZOOM button on the
    remote control for at least three seconds. The message “ZOOM 100%” will appear. Now the
    buttons  and  on the remote control as well as on the device will allow you to set the
    zoom value. The button  decreases - the button  increases the zoom value. The
    following levels are available: 50%, 75%, 100%, 125%, 150% and 200%. If the zoom level is
    larger than 100%, you have the option of moving the image by means of the arrow buttons
    on the remote control as well as the five-way multifunction button. To end the zoom function
    again, press the ZOOM button again for approx. three seconds until the function turns off and
    the next image is displayed.
    Thumbnail view
    With the thumbnail view, you have the option of having the images on the data carrier
    displayed in a set of nine small images for each page. To get to this overview, please press
    the stop button Ŷ during the slide show. The arrow buttons of the remote control or the fiveway multifunction button now give you the option of selecting the individual images or the
    navigation. By pressing the ENTER button you will confirm your selection.

    Page 23 of 44 pages

  • Page 27

    DVD7200BT

    ENGLISH

    AUX IN
    The AUX IN (brown connection cable) is a connection with which you can connect external
    audio devices through their headphone or AUX output with this device. The audio tracks
    played back on these devices are then put out through the car speakers. This is how you can
    e.g. play back audio files that you have saved on your cell phone, minidisk, iPod® or tape
    recorder. To connect external audio devices with the CD/DVD car radio, you will need a
    cable with an RCA jack (right + left) on a 3.5 mm jack plug, which is not included in the scope
    of delivery. First connect this cable to the device - and then the headphone connection or
    AUX output of your playback device. Now you can start the playback. Set the volume of the
    playback device to a medium level and subsequently regulate the volume with your
    DVD7200BT. If the playback source of the DVD7200BT has not been set to AUX yet, please
    press the “MODE” button until AUX appears on the display.
    Menu settings level 1
    By briefly pressing the volume control dial once or several times, the functions of menu level
    1, volume control, bass setting, treble setting, and the speaker balance between the left and
    right as well as front and rear speaker groups can be selected and set.
    Changing the bass settings (BASS)
    Pressing the volume control dial twice will result in reaching the bass settings. The message
    “BAS” will appear on the display together with the current level (e.g. B. “+2”). To change the
    bass bandwidth, turn the volume control dial clockwise or counter-clockwise. The bandwidth
    can be set in a range between “-7” and “+7”. It can be changed in increments of one. The
    setting is saved either when the desired value is confirmed by pressing the volume control
    dial or through automatic memory (don’t change anything on the device for approx. five
    seconds). If you confirm the selection by pressing the control dial , you will reach the next
    possible setting. If you use the automatic memory, the device will return to the standard
    display.
    Changing the treble settings (TREBLE)
    After pressing the volume control dial twice, the treble setting (TREBLE) can be reached.
    The message “TRE” will appear on the display together with the current level (e.g. “0”). To
    change the bandwidth of the treble, turn the control dial clockwise or counter-clockwise. The
    bandwidth can be set in a range between “-7” and “+7”. It can be changed in increments of
    one. The setting is saved either when the desired value is confirmed by pressing the volume
    control dial or through automatic storage (don’t change anything on the device for approx.
    five seconds). If you confirm the selection by pressing the volume control dial, you will reach
    the next possible setting. If you use the automatic memory, the device will return to the
    standard display.
    Changing the volume ratio (BALANCE)
    After pressing the volume control dial three times, the settings for the ratio between the
    speakers connected on the right and left can be reached (BALANCE). The message “BAL”
    appears on the display along with the settings for the volume ratio between the right and left
    speaker group (e.g. “BAL R2”). To change the ratio between the speakers, turn the volume
    control dial clockwise or counter-clockwise. Depending on the direction in which the control
    dial is turned, an “R” (right speaker group) or an “L” (left speaker group) will appear on the
    display, together with a digit (e.g. “R2” or “L4”). These provide information about the direction
    in which the volume ratio is changed and about the amount of the change. The ratio between
    the right and left speaker group can be set in a range between “8R” and “8L”. The volume
    ratio between the speakers changes according to the setting and the volume will increase on
    one side according to this setting and decrease on the other side. If the ratio is set to “R-L”,
    the volume on both speaker groups is the same. If the control dial is set to the maximum

    Page 24 of 44 pages

  • Page 28

    DVD7200BT

    ENGLISH

    position of “8” on one of the two sides, the speaker group on the opposite side will be muted.
    To change this, turn the volume control dial again.
    The setting is saved either when the desired value is confirmed by pressing the volume
    control dial or through automatic storage (don’t change anything on the device for approx.
    five seconds). If you confirm the selection by pressing the volume control dial, you will reach
    the next possible setting. If you use the automatic memory, the device will return to the
    standard display.
    Changing the volume distribution (FADER)
    After pressing the volume control dial four times, the settings for the speaker distribution
    between the front and rear speaker group (FADER) will be reached. The message “FAD” will
    appear on the display along with the set volume ratio between the front and rear speaker
    group (e.g. “FAD 2F”). To change the ratio between the speaker groups, turn the volume
    control dial clockwise or counter-clockwise. Depending on the direction in which the volume
    control dial is turned, an “R” or an “F” will appear on the display, together with a digit (e.g.
    “F2” or “R3”). These provide information about the direction in which the volume ratio is
    changed and about the amount of the change. The ratio between the right and left speaker
    group can be set in a range between “F8” and “R8”. The volume ratio between the speakers
    changes according to the setting. The volume of one speaker group increases, the other
    decreases. If the ratio is set to “R-F”, the volume on both speaker groups is the same. If the
    control dial for one of the two speaker groups is turned to the maximum setting “8”, the other
    speaker group is muted. To change this, turn the volume control dial again.
    The setting is saved either when the desired value is confirmed by pressing the volume
    control dial or through automatic memory (don’t change anything on the device for approx.
    five seconds). If you confirm the selection by pressing the volume control dial, you will return
    to the standard display. If you use the automatic memory, the device will return to the
    standard display.
    Note:
    If you press the volume control dial again after you reach the last settings option (here
    FADER), you will return to the standard display. If no changes are made for five seconds, the
    device will automatically return to the initial display. In DVD mode (with an open monitor), the
    settings option FADER is also followed by the functions BRIGHT, CONTRAST, COLOR and
    SHARP.
    Menu settings level 2
    You can reach menu level 2 by pressing the volume control dial for approx. two seconds.
    The individual menu items can be reached by repeatedly pressing the control dial. At menu
    level 2, the functions “LOC” (distance setting for station search), “LOUD” (sound setting),
    “ST-MO” (switching between stereo and mono playback), “CT” (set time of day), “TAVOL”
    (standard volume for traffic announcements), “EON” (automatic station switch for traffic
    announcements), “D/Z” (setting of the second playback level - DUAL ZONE) can be set.
    When the monitor is open, the functions referred to above are available to you under the
    following alternate terms: ST-MO = STMO, CT = TIME, TAVOL = TA VOL.
    LOC function to set the station search
    The “LOCAL” function is relevant for the station search. Here it can be selected whether only
    local, strong stations (“ON”) or also weaker, more distant stations (“OFF”) are searched for.
    The “LOC” function prevents a corresponding switching to a stronger station as long as it
    isn’t broadcasting the same program as the one currently being listened to. To activate the
    “LOC” function, press the volume control dial until menu level 2 is reached. The “LOC”
    function will appear. Now you have the option of activating (“LOC ON”) or deactivating (“LOC

    Page 25 of 44 pages

  • Page 29

    DVD7200BT

    ENGLISH

    OFF”) the function by turning the dial. The setting is saved either when the desired value is
    confirmed by pressing the volume control dial or through automatic memory (don’t change
    anything on the device for approx. five seconds). If you confirm the selection by pressing the
    volume control dial, you will reach the next possible setting. If you use the automatic
    memory, the device will return to the standard display.
    Note:
    This setting only affects the radio mode and can only be carried out while the radio mode is
    active.
    LOUD function for the tone setting – loudness
    The “LOUD” function makes it possible to emphasize low and high frequencies through the
    push of a button in order to increase sound perception in an adjustment to the respective
    volume. To activate the “LOUD” function, press the volume control dial until menu level 2 is
    reached. The “LOC” function will appear. Press the volume control dial repeatedly until you
    get to the menu item “LOUD”. There you will have the option of activating (“LOUD ON”) or
    deactivating (“LOUD OFF”) the function by turning the dial. The setting is saved either when
    the desired value is confirmed by pressing the volume control dial or through automatic
    memory (don’t change anything on the device for approx. five seconds). If you confirm the
    selection by pressing the control dial , you will reach the next possible setting. If you use the
    automatic memory, the device will return to the standard display. When the “LOUD” function
    (“LOUD ON”) is activated, the message “LOUD” appears on the display. This is turned off
    after deactivation.
    ST – MO function to switch between stereo and mono playback
    This menu item gives you the option of selecting between stereo and mono playback. To
    reach the menu, press the volume control dial until menu level 2 is reached. The “LOC”
    function will appear. Now briefly press the volume control dial repeatedly until you reach the
    menu item “ST-MO”. There you will have the option of selecting between “ON” and “OFF” by
    turning the dial. The selection “ON” will turn the mono playback on. “OFF” will turn the stereo
    playback back on again. The setting is saved either when the desired value is confirmed by
    pressing the volume control dial or through automatic memory (don’t change anything on the
    device for approx. five seconds). If you confirm the selection by pressing the control dial , you
    will reach the next possible setting. If you use the automatic memory, the device will return to
    the standard display. This setting only affects the radio mode and can only be carried out
    while the radio mode is active.
    CT function to set the time of day
    To set or change the time settings, press the volume control dial until you get to menu level
    2. The “LOC” function will appear. Press the volume control dial repeatedly until you get to
    the menu item “CT”. There you have the option of setting the time of the device by turning
    the dial. Turning to the right changes the number of the hours, turning to the left, the minutes.
    The setting is saved either when the desired value is confirmed by pressing the control dial
    or through automatic memory (don’t change anything on the device for approx. five seconds).
    If you confirm the selection by pressing the volume control dial, you will reach the next
    possible setting. If you use the automatic memory, the device will return to the standard
    display. If the device receives an RDS station with an RDS time signal, the clock will be
    automatically updated in particular intervals.
    TAVOL function to set the volume for traffic announcements
    The “TAVOL” function enables an adjustment of the volume of traffic announcements
    according to individual preferences. To change the device’s volume for traffic
    announcements, press the volume control dial until menu level 2 is reached. The “LOC”
    function will appear. Press the volume control dial until you get to the menu item “TAVOL”.

    Page 26 of 44 pages

  • Page 30

    DVD7200BT

    ENGLISH

    There you have the option of setting the device’s volume for traffic announcements by
    turning the dial. Turning to the right increases the volume for traffic announcements, turning
    to the left reduces the volume for traffic announcements. The volume for traffic
    announcements can be set between 0-45. Here 0 = no sound and 45 = maximum volume of
    the device. The setting is saved either when the desired value is confirmed by pressing the
    volume control dial or through automatic memory (don’t change anything on the device for
    approx. five seconds). If you confirm the selection by pressing the volume control dial, you
    will reach the next possible setting. If you use the automatic memory, the device will return to
    the standard display. During a traffic announcement, it’s possible to adjust the volume to the
    current requirements at any time through the volume control dial.
    EON for the automatic station switch for traffic announcements
    The “EON” function is an additional RDS service. If the current program doesn’t offer any
    traffic announcements, EON automatically switches to the traffic announcements on another
    program. After the end of the announcement, the device switches back to the previously
    heard station. The readiness for traffic announcements “TA” has to be activated for this. To
    activate the “EON” function, press the volume control dial until menu level 2 is reached. The
    “LOC” function will appear. Press the volume control dial until you get to the menu item
    “EON”. There you will have the option of activating (ON) or deactivating (OFF) the function
    by turning the dial. If the “EON” function is activated, “EON” will appear on the display. The
    setting is saved either when the desired value is confirmed by pressing the volume control
    dial or through automatic memory (don’t change anything on the device for approx. five
    seconds). If you confirm the selection by pressing the volume control dial, you will reach the
    next possible setting. If you use the automatic memory, the device will return to the standard
    display.
    D/Z for the settings of the second playback level (DUAL ZONE)
    The device has a second playback level (dual zone). This makes it possible to address a
    second playback medium. For example: listening to the radio on the front seats and watching
    a DVD on the back seats (this requires a second monitor). Several combination options are
    available here. To activate the function, press the volume control dial until menu level 2 is
    reached. The “LOC” function will appear. Press the volume control dial repeatedly until you
    get to the menu item “D/Z”. There you have the option of activating the function by turning
    the dial and setting the corresponding playback source. Which playback source is available
    to you depends on which storage media have been inserted or connected. Generally they
    are all available. The setting is saved either when the desired value is confirmed by pressing
    the volume control dial or through automatic memory (don’t change anything on the device
    for approx. five seconds). If you confirm the selection by pressing the volume control dial,
    you will return to the standard display. If you use the automatic memory, the device will also
    return to the standard display.

    Page 27 of 44 pages

  • Page 31

    DVD7200BT

    ENGLISH

    DVD device settings
    For the settings of the DVD drive, a separate menu is available to you. This can only be
    reached when the CD/DVD mode is activated. The submenu “preferred settings” is only
    available when the media playback has been stopped. When the monitor is open, you can
    reach the DVD device settings through the SETUP button. To get to the desired menu or the
    desired menu option, please use the five-way multifunction button to navigate. With this
    button you can navigate upward and downward. If you press the button to the right, you will
    reach the settings options of the menu item. If you press the button to the left, you will return
    to the higher level item of the settings.
    General settings

    4:3 Letterbox

    Menu entry
    TV format
    Viewing angle
    indicator
    OSD
    language
    Subtitles
    Last memory

    16:9

    4:3 Pan Scan
    16:9 Wide
    Function
    Here you can adjust the output format for the DVD playback according to
    your preferences.
    This function is indicated in the device menu but not supported by the device.
    This menu item allows you to set the language of this menu.
    This function displays subtitles as long as those are available on the data
    carrier and the function is activated.
    This pertains to a memory function that remembers the point where the
    playback was last stopped. If the function is activated, it’s possible to
    continue the playback of a movie at the point at which it was last stopped.

    Page 28 of 44 pages

  • Page 32

    DVD7200BT

    ENGLISH

    Audio settings

    Menu entry
    Analog audio
    settings

    Digital audio
    settings

    Dolby digital
    settings

    Equalizer
    settings

    3D Effect
    settings
    HDCD

    Function
    Here you can set the format in which the DVD sound should be played back.
    STEREO = analog stereo signal RIGHT / LEFT = Dolby Pro Logic stereo
    signal (2 channel sound) SURROUND = Virtual surround sound If STEREO
    has been switched on, “STR“ will appear, for RIGHT / LEFT, “LTRT“ will
    appear, and for SURROUND, “VSR“.
    This menu allows you to set the behavior of the digital output (SPDIF). Digital
    output: Here you can set how the output should be performed. “SPDF ON”
    puts out the maximum available sound quality through the connection. If this
    option is set, the abbreviation “RAW” will be indicated on the display. “ONLY
    PCM” puts out a 2 channel stereo digital sound through the output. “SPDIF
    OFF” turns off the output through the digital connection. LPCM (linear PCM)
    OUTPUT allows you to select either the audio CD standard (48K) or the DVD
    standard (96K).
    Through this menu you can adjust the behavior of the Dolby function
    according to your own preferences and determine the desired type of output.
    Stereo = stereo sound, R-mono and L-mono each play back the sound only
    through the selected channel. The setting mix-mono only functions during the
    DVD playback with DTS 5.1. In addition, you have the option of setting the
    level of the linear compression. Different levels are available to you here
    (OFF, 1/8, 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, FULL).
    Through this function you can adjust the tone color of the output sound
    according to your own preferences. Through the EQ type, you can select the
    preset sound settings. The menu item bass increase just allows you to
    increase the bass frequencies. With super bass, you have an additional
    option of increasing the bass output. The setting treble increase also allows
    you to increase the treble levels correspondingly.
    Through this function you can adjust the sound effects of the output sound
    according to your own preferences. The echo mode setting enables you to
    select one of the preset reverberating effects.
    The HDCD function enables you to carry out certain settings if you are using
    such a data carrier. Because of the low market distribution of this type of data
    carrier, this function is turned off by default.

    Page 29 of 44 pages

  • Page 33

    DVD7200BT

    ENGLISH

    Video settings

    Menu entry
    Color settings
    Sharpness
    Brightness
    Contrast
    Gamma
    Hue
    Saturation
    Luma delay

    Function
    This function enables you to adjust the color settings of the DVD playback
    according to your preferences (possible levels are listed in brackets)
    This serves to set the sharpness of the image (high / medium / low).
    This serves to set the brightness of the image (- 20 to + 20).
    This serves to set the contrast of the image (- 16 to + 16).
    This serves to set the gradation. The gradation is the exponent between the
    displayed brightness and the image or pixel values (high / medium / low /
    none).
    This serves to set the hue (- 9 to + 9).
    This serves to set the color saturation (- 9 to + 9).
    This serves to set the luminance delay. A change in this setting is only
    required if the color and brightness aren’t coextensive (“0 T” and “1 T”).

    Preferred settings

    Menu entry

    TV format

    Playback
    control

    Function
    This setting enables the selection of the appropriate TV standard. PAL is the
    customary standard in Europe. NTSC is the customary standard in the US
    and Japan. Only select the MULTI option if your TV can play back both
    formats. Here the output signal is automatically adjusted to the standard of
    the inserted DVD. If the “MULTI” setting is selected, “AUTO” will be displayed
    to the left of the selection menu.
    The playback control function serves to turn the playback control for VCD
    and SVCD data carriers on and off. This function is also abbreviated as
    “PBC”.

    Page 30 of 44 pages

  • Page 34

    DVD7200BT
    Audio
    language
    Subtitles
    Menu
    language

    Age rating

    Factory
    settings

    ENGLISH

    This enables the selection of the desired dubbed language. If the language
    selected here is not available on the inserted data carrier, the first language
    that is found will be played back.
    This enables the selection of the desired subtitles. If the subtitles selected
    here are not available on the inserted data carrier, the first subtitles that are
    found will be played back.
    This enables the selection of the desired menu language. If the language
    selected here is not available on the inserted data carrier, the first language
    that is found will be played back.
    This serves to set the desired age rating.
    After setting the age
    1) Child = Kid safe
    rating, you will be
    2) G = some guidance advisable
    prompted to enter a
    3) PG = Parental guidance suggested, some password. The factory
    material may not be suitable for children
    default password is set
    4) PG 13 = Parents strongly cautioned, some to 136900. Enter this
    material may be inappropriate for children under 13 through the number
    5) PGR = Restricted, under 17 requires buttons on the remote
    accompanying parent or adult guardian
    control. Now select
    6) R = Restricted viewing
    “YES” or “NO” with the
    7 ) NC17 = No one 17 and under admitted
    arrow buttons. Then
    8) 18 or older = for Adult Entertainment or X rated confirm your selection
    movies and NO PARRENTAL is for General with the "ENTER"
    Audiences (All Ages).
    button.
    This function resets the DVD device settings to the factory default settings.

    Password settings

    Menu entry
    Password
    protection
    Password
    Old password
    New
    password
    Confirm
    password

    Function
    This function serves to protect the selected settings. The factory default
    password is 136900.
    With this function you have the option of changing the factory default
    password.
    Enter the old password here.
    Enter the new password here.
    Confirm the new password here. After you have confirmed the password,
    please press the ENTER button on the remote control. Now the new
    password is saved.

    Note: If you have forgotten your changed password, you can set a new one at any time by
    entering the factory default password 136900.

    Page 31 of 44 pages

  • Page 35

    DVD7200BT

    ENGLISH

    Exiting the settings
    To exit the settings menu again, please navigate to the last item (X) in the bar on top.

    The menu item “exit menu” will appear. Press the five-way multifunction button once to exit
    the menu. You can also exit the menu at any time by pressing the SETUP button.
    Factory default settings (“RESET“)
    By using the reset function, the device can be changed back to the factory default settings.
    To use the reset function, please press the button REL on the device. Now the operating unit
    can be carefully detached towards the front and left. Now press the RESET button on the
    device with a thin, sharp object. The device will then be reset and turned off if required.
    Note:
    When the factory settings are restored, the clock and the stored radio stations will also be
    reset or erased.

    Page 32 of 44 pages

  • Page 36

    DVD7200BT

    ENGLISH

    Remote Controls
    Remote control (normal)
    The buttons of the remote control fulfill the same functions as the buttons with the same
    names on the device. Special functions are described in detail in the table below.

    Button
    AUDIO

    SUBTITLE
    A-B

    ZOOM

    BLUETOOTH

    Function
    Switches the audio channel of the current
    DVD to another playback language (if
    available).
    Switches the subtitle language of the current
    DVD to another playback language (if
    available).
    Repeat function

    The zoom function gives you the option of
    having the film scenes and stills displayed in
    an enlarged or reduced format. To activate
    the zoom function, keep it pressed for approx.
    three seconds.

    See Bluetooth Operation

    Remote control (Dual Zone)

    The buttons of the remote control fulfil the same functions as the buttons with the
    same names on the device. Special functions are described in detail in the table
    below.
    Button
    MODE
    AUDIO
    SUB

    MENU

    Function
    Switches the playback source.
    Switches the audio channel of the current DVD
    to another playback language (if available).
    Switches the subtitle language of the current
    DVD to another playback language (if
    available).
    Activates the screen menu of the DVD
    playback.

    Page 33 of 44 pages

  • Page 37

    DVD7200BT

    ENGLISH

    Changing the battery
    Remote control (unit)

    +
    To change the battery, the battery compartment can be pulled out towards the front.
    Now replace the old battery with a new one of the same type (CR 2025). Please pay
    attention to the polarity ("+ pole" to the top) when you insert the battery. Please only
    touch the battery on the edge, since there might be contact problems otherwise. Now
    slide the battery compartment with the new battery back into the case. Make sure
    that the battery compartment is positioned flush inside the case again after changing
    the battery.
    Remote control (DUAL ZONE)

    +
    To change the battery, please press the lock on the left side of the battery case
    slightly to the right. Now the battery compartment can be pulled out towards the front.
    Now replace the old battery with a new one of the same type (CR2025). Please pay
    attention to the polarity ("+ pole" to the top) when you insert the battery. Please only
    touch the battery on the edge, since there might be contact problems otherwise. Now
    slide the battery compartment with the new battery back into the case. Make sure
    that the battery compartment snaps back into the case.
    Note:
    Please remove the safety disk on the battery compartment before first using the
    remote control. Otherwise the remote control won’t operate properly.
    Disposal of the battery
    Please consider that you as an end consumer are obligated to return discarded
    batteries that are hazardous waste to a distributor or a redemption site intended for
    this purpose by a public waste management facility.

    Page 34 of 44 pages

  • Page 38

    DVD7200BT

    ENGLISH

    RDS OPERATION AND DESCRIPTION
    Radio Data System (RDS) enables you to make the best use of your RDS equipped unit.
    RDS allow radio stations to transmit data that will make use easier. The radio stations can
    send short messages on RDS and provide additional information about the programs being
    transmitted, weather, general information, traffic jams, the title of a record or a 'phone-in
    number, etc. RDS information is transmitted with many radio stations that broadcast on the
    FM band.
    PS (Program Service Name)
    The unit is supplied with a character display that will show the name of the selected radio
    station. When you program your favorite radio stations into the preset station numbers, it is
    not just the frequency that is stored, but also the station's identification. If you have set
    RADIO-ONE to be on button number one, then pressing this button will always give you
    RADIO-ONE wherever you are in the country.
    AF (Alternative Frequency) Automatic Tuning
    The unit receives information about the frequencies of nearby transmitters. This enables it to
    choose the strongest FM signal for the selected station. This is particularly useful and safe
    for you as a driver, you no longer have to re-tune when driving between different transmitter
    coverage areas.
    Regional Links (REG On/Off)
    Many local radio stations only have a couple of different frequencies, and their coverage area
    is limited. Some local stations are linked together according to their region, so that if the
    signal from a local radio station becomes weak, the unit can switch to another local station in
    the same region. If you wish the radio to stay tuned to the same local station regardless of
    the signal strength or quality, then you should turn the Regional facility ON, as described in
    the previous pages.
    TA and TP (Travel Announcements / Travel Program Identification)
    When a local radio station broadcasts a traffic report, the unit is informed. This information
    can be used to provide you with travel information without having to listen to that particular
    radio station all of the time. When the travel announcement is broadcast the unit will interrupt
    the AUX / Compact Disc / USB / SD-MMC that is playing and will automatically switch to the
    announcement. At the end of the announcement the unit returns to its former state by
    switching back to the CD, AUX, USB or SD-MMC.
    For this to work, the travel announcement function must be switched on. The unit will only
    allow you to tune to a station which is capable of sending the relevant RDS travel
    announcement information.
    If the signal of the selected radio station becomes weak, the unit should re-tune itself to
    another station that has the RDS travel information. The TP symbol will ignite on the
    information display, when a TP station is found or selected.
    EON (Enhanced Other Networks)
    The unit is equipped with the Enhanced Other Network (EON) function, and can switch from
    a national Network station (eg RADIO ONE) to a Local Radio travel announcement, and then
    back to the national station at the end of the announcement. For example, the unit is tuned to
    RADIO FOUR, and the TA Travel function is switched on. You may be listening to RADIO
    FOUR or to a CD, or you could have the volume turned down. When a nearby local radio
    station, such as RADIO LOCAL, is about to make a travel announcement, an RDS signal
    transmitted on RADIO FOUR tells the unit to tune to RADIO LOCAL for the announcement.
    The unit will already know the frequency of RADIO LOACAL in that area. The unit will first

    Page 35 of 44 pages

  • Page 39

    DVD7200BT

    ENGLISH

    check that it can receive RADIO LOCAL satisfactorily and, if so, will switch from RADIO
    FOUR, turn up the volume, or interrupt the playback for the duration of the announcement. At
    the end of the announcement the unit returns to its previous state ready for the next
    announcement. With EON, the unit is told about the frequencies of other radio stations in the
    area, both local and national. If you change stations, the unit will know immediately which
    frequencies to try first.
    PTY (Program Type)
    Many radio stations give codes to individual programs according to their type. The unit allow
    you to select the type of program required, and will search for a station broadcasting that
    type of program. The following program types are available: Speech, News, Current Affairs,
    Information, Sport, Education, Drama, Culture, Science, Varied Speech (quizzes/comedy),
    Pop Music, Rock Music, M.O.R.M. Easy Listening, Classical, Other Music types, Weather,
    Finance, Children, Social, Religion, Phone in, Travel, Leisure, Jazz, Country, National,
    Oldies, Folk Music and Documentations.
    To switch PTY ON, press PTY button for more than a second on the unit or remote control.
    The current selected PTY type will be shown on the information display. When no special
    type is selected NO PTY will be shown. To switch PTY OFF, press the PTY button again.
    Default PTY is “News”.
    Turn the Volume knob of the unit up or down or press the Volume buttons on the remote
    control to scroll through the available PTY types, and then press the BAND/ENTER button on
    either the remote control or the unit to automatically start searching for a radio station with
    the selected PTY code. You can also press one of the six preset buttons on the unit or the
    remote control to quickly chose from pre-selected PTY types: 1= News, 2= Speech, 3= Sport,
    4= Pop M, 5= Classical, 6= Music.
    When you want to store a PTY under one of the preset numbers, first select the preferred
    PTY type, then press and hold one of the Preset buttons on the unit. The sound will briefly
    be muted; thereafter the PTY type will be displayed. Your favorite PTY type is now stored.
    Note: After 5 seconds of non operation the display will return to the default of the selected function and will exit
    the manual station / frequency search mode.

    Time and Date (CT-Clock Time)
    Part of the RDS data is used to transmit the current time and date. The clock on the unit
    never has to be adjusted, and will automatically set itself for summer and winter time
    changes. It will also take account of leap years and, if traveling in a foreign country, will
    adjust between different time zones.
    Note: Under whatever mode, the unit will receive automatically urgent news and ALARM! will be on the
    Information Display. RDS operation is not possible during AUX mode.

    Page 36 of 44 pages

  • Page 40

    DVD7200BT

    ENGLISH

    BLUETOOTH Operation
    The unit is compatible with Bluetooth international standard wireless communication
    technology V1.2 & V2.0 EDR and supports HSP, HFP, A2DP, AVRCP. The unit has
    excellent software controlled ECHO cancellation with noise elimination You can place a
    hands-free call using a Bluetooth compatible mobile phone. When you place a call, speak
    loudly and clearly and shut the windows before calling. Certain voices may sound unnatural,
    depending on the telephone line conditions. Depending on the mobile phone in use, you may
    not be able to use the hands-free phone function.
    Pairing
    Start searching a new device Bluetooth device according the manual of your Mobile Phone.
    As soon as you phone finds "CAR RADIO", select "CAR RADIO” and key in the code "0000"
    and confirm ok,. The Phone and the unit will now start pairing and the device paring is
    finished. After a Bluetooth connection is made between the Phone and the unit, the BT
    indication will be ON and Flashing in the bottom of the screen.
    Note: When using Bluetooth for the first time with your phone and the unit, you need to pair
    the devices. After you have paired the devices, you do not need to pair it again, unless the
    unit has lost all of its power. (When the Telephone and the unit are not paired, short press
    the green button to pair the telephone and the unit. Note: the Telephone must have been
    paired with the unit once before)
    Suggestion:
    1..Set "My phone's visibility" as "show to all"
    2. Select "Yes" in "Set as authorized."
    Making a call

    In the BT mode, key in the telephone number (touch screen, Remote control or Telephone)
    and press the green button to dial the number.
    Hang up / Reject
    Press the red button to hang up a call in progress or reject an incoming call. The unit will
    go back to the previous mode automatically (e.g. Radio, CD, DVD, SD, AUX)
    Receiving calls
    When a call is received, a ring tone is heard over the speakers and the screen is indicating a
    call is being received. To pick up the call, press the green button. During a call the unit will
    stop playing. After the call is finished, the unit will go back to the previous mode automatically
    (e.g. Radio, CD, DVD, SD, AUX).

    Page 37 of 44 pages

  • Page 41

    DVD7200BT

    ENGLISH

    Voice transfer from unit to phone and vice versa
    When a call is in progress, long press the green button. The conversation will now be
    transferred to your phone. Long press the green button again and the conversation is put
    back to the unit for hands free calling.
    Telephone book pairing

    When a telephone is paired, long press the green button to enter into the READ PHONE
    menu. You will see READ PHONE in the above screen and 0/200, meaning the list is empty
    and 200 memory places are available. The unit can store 200 names and numbers. Consult
    your owners manual to transfer names from your phonebook into the unit’s phonebook by
    Bluetooth transfer. When READ PHONE is displayed you can transfer one or multiple phone
    book entries. Depending the make of your mobile phone, the names are displayed in the
    firstname, lastname or lastname, firstname order. The unit cannot reverse this order and will
    display the order as it is received from your mobile phone. To delete all entries, long press
    the C button till a beep is heard and 0/200 is displayed. Note: you can only delete the whole
    phonebook and not only one entry.
    Once a name or names are in the phonebook, the unit will display the phonebook page at
    first when the Bluetooth mode is selected. In the other Bluetooth modes, click on the book
    logo to enter the phone book list. Click on the Up or Down arrow to choose a phone number
    or name and click on OK to dial the number. Long press the up or down arrow will advance
    the phone book to the next page of numbers/names.
    Making a call from the phonebook
    Select the BT mode. Use the arrows to select a person from the list in the phonebook (will be
    highlighted) and place a call by pressing the green button. Pressing twice the green
    front panel button, you can quickly call the last dialed number.

    Page 38 of 44 pages

  • Page 42

    DVD7200BT

    ENGLISH

    A2DP (Advanced Audio Distribution Profile)
    With A2DP and Mobiles phones that support the Bluetooth A2DP protocol, songs stored on
    the mobile phone can be played wirelessly via the unit (audio streaming).

    Operation:
    (See the manual of your Mobile phone for A2DP support). Connect the Mobile phone via
    Bluetooth as described in Pairing. Play the selected song with the music player of the
    mobile phone. The song will now be heard via the speakers in your car.
    AVRCP (Audio/Video Remote Control Profile)
    AVRCP defines how to control characteristics of streaming media. This includes pausing,
    stopping, and starting playback as well as other types of remote control operations.
    Operation with the touch screen:
    1. press the PLAY one time to play a song from the Telephone
    2. press the PLAY one time again to pause a song
    3. press the  button to skip to the next song
    4. long press the  to fast forward a song
    5. press the  button to skip to the previous song
    6. long press the  button to fast backwards a song
    Note:
    This unit can support most mobile phones with Bluetooth functions such as SAMSUNG,
    NOKIA, PANASONIC, SHARP, MOTOROLA, PHILIPS, SONY ERICSSON, SAGEM etc.
    Please refer to your mobile phone’s user manual for Bluetooth setup and operation.

    Page 39 of 44 pages

  • Page 43

    DVD7200BT

    ENGLISH

    TECHNICAL SPECIFICATIONS
    GENERAL
    Operational voltage:
    Fuse:
    Grounding:
    Installation angle:
    Net weight:
    Composite video input:
    Composite video input (camera):
    Audio input (AUX, Stereo):
    Subwoofer output:
    Maximum power consumption:
    Installation size (W x H x D ):
    Station memory:
    Audio output (AUX):
    Optical SPDIF output:
    Maximum power output:
    Impedance:
    Supported Formats:

    12 V
    15 A
    Negative pole on the vehicle body
    Vertical 0° to +30°, horizontal ±15°
    2.5 kg
    1
    1
    1
    1
    10 A
    178 x 50x (165+25) mm
    30 (18 FM / 12 MW)
    2 (rear/front)
    1
    4 x 40 Watt
    4-8Ÿ
    DVD, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-R DL, DVD+R
    DL, CD, CD-R, CDRW, VCD, SVCD, MP3, WMA, OGG Vorbis and
    JPG data carriers. SD/MMC data carriers max. 2 GB

    FM / MW RADIO
    FM Frequency range:
    FM Usable sensitivity (S/N):
    FM Minimum reception level for station search:
    FM Distortion:
    FM Stereo channel separation (1 KHz):
    FM Signal/noise ratio:
    MW Frequency range:
    MW Usable sensitivity (S/N 20 dB):
    MW Distortion:
    Antenna impedance:

    87.5 – 108.0 MHz
    10 dBȝ
    20-30 dBȝV
    0.5%
    30 dB
    60 dB
    522 - 1620 kHz
    30 dBȝ
    10 dB
    75 Ÿ

    DVD PLAYER
    Signal/noise ratio:
    Dynamic range:
    Distortion factor (line out):
    Frequency range (± 3 dB):

    90 dB
    90 dB
    0.1%
    20 Hz – 20 KHz

    AUX IN
    Distortion:
    Frequency range (± 3 dB):
    Audio input level:

    0.5%
    20 Hz – 20 KHz
    1 Vrms

    VIDEO
    Normal video input level:
    Video input impedance:
    Video output impedance:
    Video output level:

    1.0±0.2V (CVBS)
    75 Ÿ
    75 Ÿ
    1.0 ± 0.2 V

    TFT MONITOR
    Video standard:
    Screen diameter:
    Visible screen area:
    Resolution:
    Brightness:
    Contrast:
    Reaction time:
    Viewing angle:
    Backlight:

    PAL/NTSC
    7 inches
    154.1 (W) x 87.0 (H)mm
    440 (W) x 234 (H) pixels
    400 cd/m
    60 (minimum)
    Increase 30 ms, decrease 50 ms
    65° from above, 40° from below
    LED, lifespan: 100000 hours (at 25°)

    ENVIRONMENT
    Temperature (operation):
    Storage temperature:
    Humidity (operation):
    Humidity (storage):

    -20° to +60°
    -30° to +80°
    45% to 80% RH
    30% to 90% RH

    Page 40 of 44 pages

  • Page 44

    DVD7200BT

    ENGLISH

    NAVIGATION CONNECTION

    [2]

    1)
    2)
    3)
    4)

    Connect the angle shaped DIN connector to the DVD7200BT (connection [2])
    Connect the straight DIN connector to the Navigation Black Box
    Connect the GPS antenna to the Navigation Black Box
    Put the Navigation Software SD card into the Navigation Black Box (contacts
    downwards)

    The Navigation Black Box will switch ON automatically when the DVD7200BT is switched on.
    If the DVD7200BT is switched off, the Navigation Black Box will stay operational for approx.
    1 Hr before it will switch OFF and will go into hibernation.
    GPS antenna installation
    The Navigation Black Box determines its position by communicating with the Global
    Positioning Satellites through its GPS antenna. The waterproof antenna may be mounted
    inside or outside of the vehicle. If you opt for interior mounting, keep in mind that the GPS
    antenna can normally not "see" through metal. You can place the antenna on the front of the
    dashboard close to the front windshield. The GPS antenna must be placed at least 10cm
    away from any physical obstruction. The antenna has an internal magnet and attaches to
    sheet or use double side adhesive. Route the he cable to the interior through a front window
    or door seal.

    Page 41 of 44 pages

  • Page 45

    DVD7200BT

    ENGLISH

    GPS main menu
    When you exit the navigation software, you will see the screen below:

    Press on Navigation, to return back to the navigation software. Press Timezone to get the
    system information and your time zone and daylight savings selection (note: you must have
    the SD card inside the NAVI box to keep the time zone stored). Press on Calibration, to
    calibrate the touch screen.
    CALIBRATION of the touch screen.

    Follow the black cross and carefully press the center of the black cross. Press once more on
    the centre of the screen when the black cross is not visible anymore, then the system will
    save the current calibration data. After you finish calibration, the screen will return to previous
    menu item.

    Page 42 of 44 pages

  • Page 46

    DVD7200BT

    ENGLISH

    SERVICE AND WARRANTY
    In case of technical problems with your product, contact the sales outlet where you have
    purchased this product
    Rho-Delta Automotive & Consumer Products BV grants you a 1-year warranty from the
    invoice date. In case of defects, the buyer only has a right to subsequent performance. This
    subsequent performance will include either repair or the delivery of a replacement product.
    Exchanged units or parts will be the property of Rho-Delta Automotive & Consumer Products
    BV. Evidence of the warranty must be provided in the form of proper proof of purchase
    (sales receipt or invoice).
    Damage caused by improper handling, operation storage or by force majeure or other
    external influences is not covered by the warranty. The same applies to wearing parts, e.g.
    rechargeable batteries (6 months).
    Questions on Navigation maps and routing issues, please consult www.teleatlas.com

    Page 43 of 44 pages

  • Page 47

    DVD7200BT

    ENGLISH

    EU DECLARATION OF CONFORMITY/ EU KONFORMITÄTSERKLÄRUNG/ EU DECLARATION DE
    CONFORMITÈ/ EU DECLARATION DE CONFORMIDAD
    We herewith declare that / Hiermit erklären wir,/ Nous déclarons par le présente/ Declaramos que el
    producto denomidado como sigue;
    BULLIT / C2000BT / Car Radio with Bluetooth
    Is in accordance with the Radio and Telecommunications Terminal Equipment Act (FTEG) and
    Directive 1999/ 5/EC (R&TTE Directive) as for radio equipment. The product is in compliance with the
    accentual requirements of § 3 and the other relevant Provisions of the FTEG (Article 3 of the R&TTE
    Directive).
    Der Richtlinie über Funkanlagen und Telekommunikationseinrichtungen (FTEG) entspricht, sowie der
    Richtlinie 1999/ 5/EC (R&TTE) als Radioausstattung. Dieses Produkt entspricht den grundlegenden
    Anforderungen des § 3 und den relevanten Bestimmungen des FTEG (Artikel 3 der R&TTE).
    Est en accord avec la loi sur les équipements radio et terminaux de télécommunication ( FTEG) et
    avec la directive 1999/ 5/EC (R&TTE) comme équipement radio. Ce produit est conforme aux
    conditions requises par le § 3 et autres réglements du FTEG (Article 3 de la directive R&TTE).
    Es conforme con las disposiciones del Acta de Terminales de Equipo de Radio y Telecomunicaciones (FTEG) y con la Directiva 1999/ 5/EC (Directiva R&TTE), como equipo para equipo
    de radio. El producto es conforme con los requerimientos actuales del § 3 y otras provisiones
    relevantes del FTEG (articulo 3 de la Directiva R&TTE).
    Standards Applied:/Angewendeter Standard:/ Standards appliqués/ Estándares aplicados:
    EN 300 328 V1.6.1 : 2004
    EN 301 489-1 V1.6.1 : 2004-07
    EN 55022 : 1998 + A1 : 2000 + A2 : 2003
    EN 55024 . 1998 + A1 : 2001 + A2 : 2003
    EN 61000-3-2 : 2000 + A2 : 2005
    EN 61000-3-3 : 1995 + A1 : 2001
    EN 60950-1 : 2001
    This according to standard 1999/5/EG
    This Declaration is in responsibility of the Importer
    Date of Issue : 29.08.2008

    Rho-Delta Automotive & Consumer Products BV
    Villa California Building
    Escudostraat 2
    2991 XV Barendrecht-Rotterdam
    The Netherlands

    Page 44 of 44 pages

  • Page 48

    DVD7200BT

    ENGLISH

    Page 45 of 44 pages




Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bullit DVD7200BT wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von Bullit DVD7200BT in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 1,15 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info