Bedienungsanleitung Burley D-lite 1996-2003 (Seite 12 von 12) (Englisch)

632516

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Your Wide Screen 2-in-1 Cover is held in place by six snaps at the

front, rear, and top. Note that the cover has a screened logo on the

rear facing panel. Always use your cover to keep debris out (and toys

inside) of the trailer when it’s in tow.

The Wide Screen 2-in-1 Cover features a clear plastic flap in front

and a tinted plastic flap in the rear. To install, first snap the mesh

portion to the roll bars, then fasten the rain flaps to the mesh

portion.

To make your trailer more visible, clip a light into the light-holder tab

sewn on the upper part of the back of your cover. There are several

brands of inexpensive clip-on lights that will make your trailer more

visible to motorists and other cyclists. You’re done! Please go back

over these directions and recheck your work.

IMPORTANT: Read and study sections “IX. Hitching the Burley

d’Lite to Your Bicycle,” “XI. Safety Guidelines,” and “XII. Safety

Checklists” before using your Burley d’Lite.

IX. Hitching the Burley d’Lite to Your

Bicycle

The trailer hitch was designed to quickly and safely attach to

virtually all types of bicycles. It is inserted in front of the left rear

dropout of your bicycle.

Hitching the Trailer to Your Bicycle

Loosen the knob on the eyebolt until the two arms are spread fully

apart. Slip the lower hitch arm under the chain stay (A) and the

upper arm above the seat stay (B). (See illustration on next page.)

Wedge the hitch cone all the way back into the angle formed by the

stays at the wheel. Tighten the knob until the arms are firmly

clamped against the stays. Wrap the safety strap around the inside

of the chain stay, over the hitch body, and back to the D-ring at the

end of the tongue.

Make sure that the cone is wedged securely into the stays. The knob

should be finger-tight; do not overtighten. The hitch should not move,

but should allow the bicycle complete movement, including lying it down

on the ground. It should clear any racks, bags, or fittings you have on your

bicycle. If there is any interference, contact your Burley dealer.

IMPORTANT: Remove trailer from your bicycle when it’s not in use

to prevent deforming the plastic hitch.

Do not operate trailer without hitch safety strap properly installed. A

dangling safety strap can contact spokes and damage rear wheel or cause

accident resulting in serious injury.

Hitch must seat properly into stays and not interfere with racks, bags, or

fittings. Inspect hitch and tongue frequently for damage or loose fasteners.

Interfering parts or damaged hitch can cause accident resulting in serious

injury.

Do not use or store trailer at temperatures below 32˚ Fahrenheit as hitch

rubber flex connector can become brittle and possibly break, causing

accident resulting in serious injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Burley D-lite 1996-2003 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info