632454
5
Zoom out
Zoom in
Vorherige Seite
1/15
Nächste Seite
8 B U R L E Y T R A I L E R O W N E R S I N S T R U C T I O N A N D S A F E T Y M A N U A L
B U R L E Y T R A I L E R O W N E R S I N S T R U C T I O N A N D S A F E T Y M A N U A L 9
Mounting the Reflectors
Cub
: Factory-installed Bee
: Rear Reflectors Only
All other models:
FRONT: Clear front reflectors are mounted horizontally to both sides of the
trailer fabric front. “TOP” is marked on the reflector front. Locate the grom-
mets on the trailer fabric front, insert the screw into the reflector back through
the grommet, and tighten snugly. Repeat for the other side.
REAR: Red reflectors are mounted horizontally to both sides of the rear of the
main frame tube, with the reflectors extending out past the sides.
1. Snap the posts on the red reflectors into the openings in the reflector
brackets, and with the provided screw, screw the pieces together.
2. Loosen the black screw next to the clamp (A) on the reflector bracket.
Slide the bracket clamp onto the rear side section (B) of the main
frame tube. Make sure the reflector side marked TOP is to the top.
3. Tighten screw snugly, making sure reflector extends out past the trailer
side. Repeat for the other side.
Make sure both reflectors face outward. Incorrectly installed reflectors
can reduce visibility at night and cause an accident or serious injury.
WARNING
Attaching the Wheels
First, verify that the tires are inflated to 30-35 P.S.I. Tip the trailer frame
onto its rear end. With the quick-release lever in the “OPEN” position, insert
the wheel axle assembly completely into the hollow trailer axle, making sure
that the horizontal shaft goes all the way into the axle. Tighten the thumb
nut, so that you feel resistance halfway though tightening the lever. Once the
wheel is fully seated in the hollow axle, position the quick-release lever so
that it is aimed to the rear of the trailer in the “CLOSED” position (the lever
is marked for OPEN or CLOSED positions). Repeat for the other wheel. Note:
wheels are not centered on the axle.
Make sure wheels are held securely, with wheel shaft fully inserted into
the hollow axle. You should not be able to rock or shift wheels. Improp-
erly installed wheels can fall off, causing an accident or serious injury.
WARNING
A
B
C
Mounts
horizontally
to frame
Quick-release
lever in unlocked
“Open” position
Quick-release
lever in locked
“Closed” position
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Burley Encore 2007 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info