Bedienungsanleitung Burley Flatbed 2007 (Seite 4 von 11) (Englisch)

632537

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

6 B U R L E Y T R A I L E R O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L

B U R L E Y T R A I L E R O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L 7

Mounting the Reﬂectors

Nomad

™

: The reﬂector brackets mount on the outside rear of each side

panel, 2.5” up from the plastic connector on the side panel. (The holes

for the mounting screws are covered by the fabric.)

To mount the bracket, insert a self-tapping bracket

screw through the hole in the curved section of the

reﬂector and drive the screw through the fabric,

into the hole in the rear side panel frame. (This

does not harm the fabric.) Then mount the reﬂector

onto the bracket with the reﬂector screw. Repeat for

the bracket and reﬂector on the other side panel.

See illustrations.

Flatbed

™

: The reﬂectors are mounted to the reﬂector

brackets on the rear of the main frame tube. Snap

the posts on the reﬂectors into the openings in the

brackets, and with the provided screws, screw the

pieces together. Tighten the screws snugly, making

sure the reﬂector faces away from the trailer.

Attaching the Wheels

First, verify that the tires are inﬂated to 30-35 P.S.I.

Tip the trailer frame onto its rear end.

Nomad

™

: With the quick-release lever in the “OPEN” position, insert the wheel

axle assembly completely into the hollow trailer axle, making sure that the

horizontal shaft goes all the way into the axle. Once the wheel is fully seated

in the hollow axle, position the quick-release lever so that it is aimed to the

rear of the trailer in the “CLOSED” position (the lever is marked for OPEN or

CLOSED positions). Repeat

for the other wheel.

Flatbed

™

: Remove the thumb nut from the quick-release

lever. Insert the quick-release lever through the hollow

axle of the wheel, making sure the lever is on the ﬂat

side of the wheel and the springs are mounted on each

side as shown in the illustration. With the quick-release

lever in the unlocked position, place the wheel into the

dropouts, making certain that the axle goes all the way

into the slots. Once the wheel is fully seated, replace

and tighten the thumb nut. You should feel resistance

halfway through closing the lever. Position the quick-

release lever so that it is aimed to the rear of the trail-

er in the “CLOSED” position (the lever is marked for

OPEN or CLOSED positions). Repeat for the other wheel.

Note: Wheels are not centered on the axle.

Make sure the wheels are held securely; you should not be able to rock or

shift them. Do not operate with tires inﬂated above 35 P.S.I. Improperly in-

stalled wheels or over-inﬂated tires can cause an accident or serious injury.

WARNING

Installing the Side Rails

Nomad

™

: Flip the four plastic (C-shaped) side

panel hold-downs to the outside. Slide each

side rail down over the side rail guides at the

front and rear of each side of the main frame.

The narrower end of each side panel goes to

the rear, with the “Burley” logo facing outward.

Snap the plastic side panel hold-downs over the

side panel tubing at the front and rear of each

side as shown.

2.5”

Right

rear

Wheels are dished off-center and must be installed so

that tires are offset away from side rails, closest to outer frame.

IMPORTANT:

Side

Panel

Hold-down

(snapped

in place)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Burley Flatbed 2007 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info