Bedienungsanleitung Burley Nomad 2007 (Seite 5 von 11) (Englisch)

632536

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

8 B U R L E Y T R A I L E R O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L

B U R L E Y T R A I L E R O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L 9

All four side panel hold-downs must be snapped in place before using the

trailer. Otherwise, the side rails can shift or collapse, resulting in the loss of cargo.

WARNING

Installing the Tailgate and Splashguard

Nomad

™

: Thread the rear tie-down straps through the inner and then outer

slots of the male buckle sections of the rear side release buckles, which

are attached to the female buckle

sections on the inside rear of the

side panels. Allow enough slack so

you can loop the webbing straps

over the rear of the side panels. To

attach the front splashguard to the

front of the side panels, repeat this

step using the front tie-down straps

and the front side release buckles.

To accommodate different sizes of

cargo, tighten or loosen the web-

bing straps as required (see illus-

tration).

Installing the Roll Bar

and Cover

Nomad

™

: Place the cover, right side out, over the side rails with the

“Nomad” logo at the front of the trailer. Slip a roll bar knob through one of

the grommets on the cover. Slide the

roll bar through the casing in the top

of the mesh divider. Align one end

of the roll bar with its corresponding

hole on the side rail. Thread the

roll bar knob through one side rail,

and tighten it into the roll bar (see

illustration). Repeat this step for the

roll bar knob on the other side. Pull

the B-tabs down and loop the rubber

O-rings over the trailer frame. Make

sure the cover extends over the top

of each side panel.

Installing the Tongue for

the Nomad

™

Tip the trailer onto its back end.

Slide the tongue onto the pivot

pin at the left front. Remove

the hairpin cotter and lock pin

from the front tongue receptacle,

rotate the tongue up into place,

and snap it into the two plastic

tongue receptacles. Push the lock

pin fully into the front tongue

receptacle. Rotate the lock pin

and locate the hole in it, between

the receptacle and the trailer

frame. Anchor the lock pin by

inserting the hairpin cotter all the

way into the hole in the lock pin.

Never operate the Nomad

™

trailer without tongue lock pin and hairpin

cotter locked in place. An unlocked tongue can loosen or detach and

cause an accident, resulting in serious injury.

WARNING

Installing the Tongue for the Flatbed

™

Rotate the tongue up into the plastic tongue

receptacle at the front frame. To lock the

tongue in place, slip the retaining pin

through the hole in the tongue receptacle

and close the pin (see illustration).

B-tab

Tailgate

Splashguard

Trailer Frame

3. Anchor Lock Pin

with Hairpin Cotter

4. Anchor Lock

Pin with

Hairpin Cotter

1. Slide

Tongue

onto

Pivot Pin

2. Rotate Tongue

into Place

5. Lock Pin and Hairpin

Cotter Locked in Place

(viewed from underside)

The retaining pin must be locked

in place before using the Flatbed

™

trailer; otherwise, the tongue could

shift and cause an accident and

serious injury.

WARNING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Burley Nomad 2007 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info