Bedienungsanleitung Byron BY112 (Seite 1 von 2) (Englisch)

558649

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

™

Plug-in & Portable

Wire Free Chime Kit

1: Place a small flat screwdriver

into the locking clip on the

base of the Bell Push

2: Gently twist

3: The backing plate will unclip

Functions:

1: Push Button 5: Portable Chime

2: Melody Selector 6: Speaker

3: Bell Push Battery 7: Plug-in Chime

4: Signal Sent LED

BY112

1: plug Chime into a UK 3pin

socket, 220 – 240V ~ 50Hz.

2: Switch the socket on.

Beep

1: The Chime will ‘Beep Beep’.

2: Press the Bell Push within

60 seconds to learn the

Bell Push to the chime.

3: The Chime Will Ring to

confirm setup, wait 60

seconds for the Chimes

to exit the learn mode

before repressing the Bell

Push.

4: Replace the battery cover.

Note: Maximum of 2 Bell

Pushes can be learnt to a

single Chime for Front/Back

Door use.

To select a melody for the Door Chime

1: Remove the Back Plate from the Bell

Push

2: Press the Melody Select button.

3:The chime will play the newly selected

sound

4: Press again to select the next melody.

Note: For Front/Back door setup, select a

different melody in one of the Bell Pushes.

CR2032

New Chime

Adding Additional Chime/Bell Push:

Additional Chime

To add an additional Chime unit to the Door Chime kit

1: Remove the batteries or unplug your NEW Door Chime and wait

for 10 seconds.

2: Replace the batteries, making sure the Positive/Negative

terminals match the internal markings or plug the Door Chime into

the Socket and switch the socket on.

3: The Chime will ‘Beep Beep’ to indicate that it has entered

the Learn mode.

4: Press the Bell Push within 60 seconds, to pair the additional

Chime to the Bell Push.

5: Chime will ring to confirm setup, wait 60 seconds for the Chime

to exit the learn mode before repressing the Bell Push.

Additional Bell Push

To add an additional Bell Push to the Door Chime kit

1: Remove the batteries or unplug your new Door

Chime and wait for 10 seconds.

2: Replace the batteries, making sure the

Positive/Negative terminals match the internal

markings or plug the Door Chime into the Socket

and switch the socket.

3: The Chime will ‘Beep Beep’ to indicate that it has

entered the Learn mode.

4: Press both Bell Pushes within 60 seconds, to pair the additional

Bell Push to the Chime.

5: Chime will ring to confirm setup, wait 60 seconds for Chime to exit

the learn mode before repressing the Bell Push. For Front/Back

door setup, select a different melody in one of the Bell Pushes -

See Melody Selection.

Note: Maximum of 2 Bell Pushes can be learnt to a single

Door Chime.

Beep

Front Door

Back Door

1: Remove the battery cover of

the Door Chime.

2: Insert 3 X 1.5V Size ‘AA’

batteries (Not Supplied).

3: Make sure the

Positive/Negative terminals

match the internal markings.

3 x 1.5V ‘AA’

4 Selectable Melodies

1: Ding Dong (Repeat) 3: Alarm

2: Westminster 4: Ding Dong Ding

1: Insert CR2032 battery

(Supplied) into the battery

holder.

2: Make sure the positive side

is facing upwards.

3: Replace back plate.

Warning: Make sure that the batteries are

replaced correctly to avoid battery failure.

Only replace with same or equivalent type.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Byron BY112 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info