Bedienungsanleitung Cadac 98251 - Entertainer (Seite 4 von 6) (Englisch)

684202

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

4. Fitting and Changing the Gas Cylinder

• Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the regulator is in position and in good condition.

• Carry out this check each time you  t the appliance to a gas cylinder (see  g. 1).

• Blow out any dust from the cylinder opening to prevent possible blockage of the jet.

• Ensure the gas cylinder is  tted or changed in a well ventilated location preferably outdoors, away from any source of ignition such as

naked  ames, and away from other people.

• Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto the cylinder until it is fully engaged.

• If there is a leak on your appliance (smell of gas), extinguish all sources of ignition in the vicinity of the appliance. If you wish to check

for leaks on your appliance, use soapy water which is applied to the suspected area. A formation of bubbles will indicate a gas leak.

Check that all the connections are securely  tted and re-check with soapy water. If you cannot rectify the gas leak, do not use the

appliance. Contact your local CADAC stockist for assistance.

• When changing a gas cylinder,  rst close the cylinder valve and then the appliance valve, making sure the  ame is extinguished and

unscrew the regulator. Re- t the regulator to a full cylinder following the same precautions as described above.

• After the appliance has been fully assembled, perform a gas leak test before operating the appliance.

• Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto the cylinder until it is fully engaged.

5. General Maintenance

• There are no predetermined maintenance intervals for this appliance.

• It is dangerous to use an appliance with a cracked or perished seal and/or hose. Inspect both seals and hose regularly and replace if

they are not in order before using the appliance.

• If the appliance was in use it will be hot. Allow to cool suf ciently before attempting any maintenance.

• CADAC Patio BBQ’s are  tted with spesi c CADAC jets to regulate the correct amount of gas. Should the hole in the Jet become

blocked this may result in a small  ame or no  ame at all. Do not attempt to clean the Jet with a pin or other such device as this may

damage the ori ce, which could make the appliance unsafe.

5.1. Replacing a Blocked Jet

• Ensure that the cylinder valve is closed, then disconnect the appliance from the gas cylinder.

• Remove the grill plates. Remove the  ame tamers to expose the burners. Remove the retaining screws of the affected burner.

• Remove the affected burner by lifting it out of its location taking care not to damage the control valve whilst doing so. This will expose

the Jet.

• Unscrew the blocked Jet with a suitable spanner and replace it with a new Jet. Do not use pliers on the Jet as they can cause damage,

making the Jet unusable or impossible to remove.

• Do not over tighten as this may damage the Jet. To re-assemble, reverse the above procedure.

3. Using the appliance

• Place the cylinder inside the cabinet in the space provided.

• Use this appliance only on a  rm level surface.

• Before use ensure that the drip cup/tray is in place.

• Make sure the gas cylinder is correctly  tted to the appliance.

• Ensure the cylinder control valve is in the open position.

• To light the appliance using the automatic igniter, push in and turn the control knob in an

anti-clockwise direction until spring resistance is felt. Hold the knob in this position for

3 – 5 seconds to allow the gas to  ow and then turn the knob fully anti-clockwise to the

HIGH position. This will cause the automatic lighter to light the burner. Should the burner

not ignite the  rst time, turn the control knob to the OFF position and wait 5 minutes,

repeat the process until the burner ignites.

• Note! All burners are  tted with an automatic igniter.

• Cross lighting: To light the burners using cross lighting, light the left burner as described

above.

• To light the remainder of the burners, simply turn their control knobs to the HIGH position

while ensuring that the lighting sequence is such that any burner to be lit up is directly

adjacent to a burner which is already burning.

• Manual ignition: To light the burners manually,  rst remove the cast iron grill plate and

the de ector plate directly underneath it. Ignite a match or  relighter and position it next

to the left hand burner. Turn on the gas supply to that burner only by pushing the control

valve in and turning it in an anti-clockwise direction. This will ignite the burner. Once the

burner is ignited, carefully replace the de ector plate and cast iron grill plate. You will

now be able to light the remainder of the burners as described in ‘Cross lighting’ above.

• Use the control knobs to adjust the individual burner  ame intensity to the desired level

by turning the knob anti-clockwise to decrease the  ame and clockwise to increase it (see

 g.3).

• After use,  rst close the valve on the gas cylinder. When the  ame is extinguished, close

the burner control valves on the appliance by turning control knobs fully clockwise.

Fig. 3

503-0604 LEV7 (98250-31, 98250-33, 98251-43) Cadac Entertainer 3 & 4 - User Manual (EU & SA).indd 3 08/09/2017 11:56:20

Cadac 98251 - Entertainer Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadac 98251 - Entertainer

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info