Bedienungsanleitung Cadac 98500 (Seite 4 von 6) (Englisch)

684203

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

2. Safety Information cont.....

3. Using the Appliance



Hang the cylinder from the bracket situated on the side of the BBQ.

Use this appliance only on a firm level surface.

Before use ensure that the drip tray is in place. It is recommended that sand is placed in the drip tray

in order to catch dripping fat and prevent flaring. It will also assist in cleaning after use as the fat will

be easier to remove from the surface of the drip tray.

Never place sawdust or any other combustible material in the drip tray.

Make sure the gas cylinder is correctly fitted to the appliance.

Ensure the cylinder control valve is in the open position.

To light the appliance using the automatic igniter, push in and turn the control knob in an anti-

clockwise direction until spring resistance is felt. Hold the knob in this position for 3 – 5 seconds to

allow the gas to flow and then turn the knob fully anti-clockwise to the ON position. This will cause the

automatic lighter to light the burner. Should the burner not ignite the first time, turn the control knob to

the OFF position and wait 5 minutes before repeat the process until the burner ignites.

Note! All burners are fitted with an automatic igniter.

Cross lighting: To light the burners using cross lighting, light the left burner as described above.

To light the remainder of the burners, simply turn their control knobs to the HIGH position while

ensuring that the lighting sequence is such that any burner to be lit up is directly adjacent to a burner

which is already burning.

Manual ignition: To light the burners manually, first remove the cast iron grill plate and the deflector

plate directly underneath it. Ignite a match or firelighter and position it next to the left hand burner.

Turn on the gas supply to that burner only by pushing the control valve in and turning it in an anti-

clockwise direction. This will ignite the burner. Once the burner is ignited, carefully replace the

deflector plate and cast iron grill plate. You will now be able to light the remainder of the burners as

described in 'Cross lighting' above.

Use the control knobs to adjust the individual burner flame intensity to the desired level by turning the

knob anti-clockwise to decrease the flame and clockwise to increase it (see fig.3). If flaring occurs,

first check that the primary air supply openings in the burner mixing tube are not blocked.

After use, first close the valve on the gas cylinder. When the flame is extinguished, close the burner

control valves on the appliance by turning control knobs fully clockwise.

4. Fitting And Changing The Gas Cylinder



Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the regulator is in

position and in good condition.

Carry out this check each time you fit the appliance to a gas cylinder (see fig. 1).

Blow out any dust from the cylinder opening to prevent possible blockage of the jet.

Hang the cylinder on the Cylinder Bracket situated on the side of the trolley.

Ensure the gas cylinder is fitted or changed in a well ventilated location preferably outdoors, away

from any source of ignition such as naked flames, and away from other people.

Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto the

cylinder until it is fully engaged.

If you wish to check for leaks in your appliance, do it outside. Do not try to detect leaks using a flame. The

correct way is to smear the suspected area with soapy water. If bubbles form, then there is a gas leak.

Immediately turn off the gas supply firstly by closing the control valve on the gas cylinder and then the

appliance valves. Check that all the connections are properly fitted. Re-check with soapy water. If a gas

leak persists return the product to your CADAC dealer for inspection/repair.

Ensure that the gas cylinder is connected or changed in a well ventilated area, preferably outdoors, away

from any source of ignition such as open flames, and away from other people.

Keep gas cylinders away from heat and flames. Do not place on a stove or any other hot surface.

Ensure that the assembled unit is stable and does not rock.

Do not cover or change the primary air supply openings in the burners as this will affect the performance

of the product and may lead to an unstable flame.

In the event of burn back, (where the flame burns back and ignites at the jet), immediately turn off the gas

supply by first closing the control valve on the gas cylinder and then the appliance valve.After the flame is

extinguished remove the regulator and check the condition of its seal. Replace the seal if in doubt. Re-

light the appliance as described in Section 3 below. Should the flame light back persistently return the

product to your authorized CADAC repair agent.

Do not modify the appliance or use it for anything which it has not been designed for.

During use, part of the appliance will become hot, particularly the cooking areas and the hood. Avoid

touching hot parts with your bare hands. The use of oven gloves is recommended.

Keep young children away from the appliance at all times.

This appliance consumes oxygen and needs ventilation for optimum performance and for the safety of

those in close proximity.

Do not move the appliance while in use.

The parts sealed by the manufacturer or its agent must not be altered by the user.

Any modification of the appliance may be dangerous.

Do not twist or pinch the hose. Ensure that it is kept away from the BBQ body so as to prevent

deterioration/damage to the hose caused by heat.

Fit one end of the low pressure hose onto the regulator nozzle, and the other end onto the Patio BBQ

nozzle by pushing the ends on as firmly as possible. Clamp into position using a hose clamp at both ends

of the hose.

Ensure that the connections are made securely and do not allow gas to leak.

Check for gas leaks before using the appliance.

For use with an approved hase and regulator connected to a refillable gas container not exceeding 11kg

and complying with local regulation in force.



NOTE

Fig.1

Fig.2

Fig.3

Cadac 98500 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadac 98500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info