Bedienungsanleitung Caliber RMD 571 (Seite 11 von 17) (Englisch)

497332

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

3. TUNE/SEEK UP/DOWN BUTTONS

In RADIO mode:

1) Long press the >>| or |<< button to automatically search up or down for a

available station from the current frequency.

2) Briefly press the >>| or |<< button to manually search up or down with step

by step for your desired station from the current frequency.

4. APS BUTTON

In RADIO mode:

1) When long pressing the APS button, the radio searches from the lowest

frequency and checks the signal strength level until 1 cycle search is finished.

And then the 6 strongest stations are preset to the corresponding preset

number memory bank. The AS operation is implemented in each bank of the

selected band. When the AS operation is finished, it will scan each preset station

for 5 seconds in FM or MW band from M1 when APS button is pressed briefly.

After the scanning is finished, broadcasting will resume on the M1.(It can store

3x6 stations for FM and 2x6 stations for MW)

2) When pressing the APS button briefly, the radio will scan each preset station

for 5 seconds in FM or MW band from M1.

After finishing a circle of scanning, it will resume broadcasting on the M1.

NOTE: In FM band, FM1,FM2,FM3 is checked one at a time; In MW band,

MW1, MW2 is checked one at a time.

5. PRESET STATION [ 1-6 ] BUTTONS

In RADIO mode:

1) To memorize the current frequency on the current band, long press any of the

number buttons (1-6) on remote control or on the front panel .

2) To recall the preset memory on the current band, briefly press one of the preset

buttons [1-6] on remote control or on the front panel.

6. STEREO/MONO BUTTON

Press the ST button on the remote control to select the STEREO or MONO

sound mode for FM band.

7. LOC BUTTON

1) In RADIO mode, when the signal of the distance radio station are very weak

and the receiving effect is bad during tuning. If there is the word LOC on the

monitor, press this button to turn off the LOC function, then tune again for the

distance radio station;

2) In RADIO mode, when the signal of the local radio stations are too strong and

the interference does no t allow the tuner to lock on stations, press this button

to turn on the LOC function to display the word LOC on the monitor, then tune

again for the local radio stations.

8. PTY (PROGRAM TYPE) BUTTON

Press the PTY button shortly to select one of the following mode:

PTY MUSIC group- - PTY SPEECH group -- OFF

1010

When PTY group is on, press the VOL+ or VOL- button on the remote control

or rotate the VOL knob on the front panel to select one of PTY programs

as follows:

<-->NEWS<-->AFFAIRS<-->INFO<-->SPORT<-->EDUCATE<-->DRAMA

<-->CULTURE <-->SCIENCE<--> VARIED<-->WEATHER<--> FINANCE

<-->CHILDREN<-->SOCIAL<-->RELIGION<-->PHONE IN<-->TRAVEL

<-->LEISURE<-->DOCUMENT< -->PTY NONE<-->POP M< -->ROCK M

<-->EASY M<-->LIGHT M<--> CLASSICS<-->OTHER M

<-->JAZZ<-->COUNTRY<-->NATION M<-->OLDIES<-->FOLK M<-->

When PTY group is on, pressing the 6 number buttons also can select one of

PTY programs as above.

After selecting one of the PTY programs, it will display SEEK PTY and

automatically search for the station of the PTY program. If the station of the

PTY program does not exist, it will display PTY NONE and then return back to

the normal station.

9. AF [ALTERNATIVE FREQUENCIES] BUTTON

When AF button is pressed briefly, the AF switching mode is selected and the

status of the AF switching mode is displayed by AF segment on the display.

Segment off: AF switching mode off.

Segment on: AF switching mode on, and has RDS information.

Segment flashing: AF switching mode on, but RDS information is not

received yet.

When the AF switching mode is selected, the radio checks the signal strength

of the AF all the time. The interval of checking time of each AFs depends on

the signal strength of the current station, from a few minute for the strong

station to a few seconds for the weak station. Every time when a new AF is

stronger than the current station, it switches over to that frequency for very

short time, and the NEW FREQUENCY is displayed for 1-2 second. Because

the mute time of the AF switching or the checking time is very short, it is almost

inaudible in case of normal program. (When AF flashes on the monitor, it will

search for the stronger RDS station. If AF and TP flash on the monitor, it can

only search for the traffic announcement station).

In FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY functions can

only receive and save the RDS program.

10. TA [TRAFFIC ANNOUNCEMENT] BUTTON

Press the TA button briefly to turn on TA search mode.

When traffic announcement is transmitted:

1).If the unit is in Disc Play mode, it will switch to radio mode temporarily.

2).Temporarily switches over to an station with traffic announcement, and TA,

TP will be displayed on the monitor.

* TA interruption function:

The current traffic announcement is cancelled by pressing TA button briefly.

* When TA is on, SEEK, (SCAN), AUTO MEMORY functions can be received

or saved only when traffic program identification code has been received.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caliber RMD 571 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caliber RMD 571

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info