Bedienungsanleitung Cambridge Audio Azur 351R (Seite 9 von 22) (Englisch)

497534

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

41 2 3

351Razur

ENGLISH

Front panel display Loudspeaker connections

HDMI inputs

Indicates the current HDMI source input.

TONE

Indicates whether the Tone controls are in use.

PCM

Indicates the 351R is receiving two channel or multi-channel PCM.

Surround decoding mode indicators (PCM, Dolby

Digital, DTS etc)

Shows the current decoding mode, Dolby Digital, DTS etc. In conjunction with

the Output Channel indicators these give full details of the current processing

mode.

Main information display

Shows the current source selected, also the surround mode and station

name/frequency when in tuner mode etc.

Output channel indicators

Shows the currently active channels depending on decoding mode and

source material. Channel icons lit indicate channels in the source material.

Icons with a box around them indicate channels being output by the 351R.

Display examples

Indicates a 5.1 DTS master audio source being played back. The lit LFE

indicates a low frequency effects channel is present in the source material.

When this icon isn't boxed it indicates the LFE channel is not being sent to a

subwoofer but will be mixed into the front left and right instead.

Indicates a 2.1 output created in the digital domain from analogue input

material.

To avoid damaging the speakers with a sudden high-level signal, be sure to

switch the power off before connecting the speakers. Check the impedance

of your speakers. Speakers with an impedance of 8 ohms (each) are

recommended.

The coloured speaker terminals are positive (+) and the black speaker

terminals are negative (-). Make sure correct polarity is maintained at each

speaker connector or the sound can become weak and "phasey" with little

bass.

Prepare the speaker cords for connection by stripping off approximately

10mm (3/8") or less (no more than 10mm, as this could cause a short-circuit)

of the outer insulation. Twist the wire tightly together so there are no loose

ends. Unscrew the speaker terminal knob, insert the speaker cable, tighten

the knob and secure the cable.

Note: All connections are made via loudspeaker cable, except if using an

active subwoofer which would be connected via a standard RCA phono

cable. Banana Plugs (4mm standard) connected to the speaker cable are

recommended for direct insertion into the speaker terminals.

Please refer to the 'Speaker Conguration' section of this manual for more

information on 5.1 speaker setups.

Aerial connections

FM aerial

Connect an aerial to the FM 75 ohm socket (a simple wire aerial is supplied

only for temporary use). Extend the lead and move the aerial around until you

get the best reception. For continued use, we strongly recommended using a

75ohm outdoor FM aerial.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio Azur 351R Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio Azur 351R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info