Bedienungsanleitung Cambridge Audio Azur 351R (Seite 14 von 22) (Englisch)

497534

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

To perform the Auto Setup function, rst connect the supplied microphone to

the front panel 'Mic In' input and place it at your normal listening position in

the room. It should also be placed at normal listening height.

Press the

button on the remote control to access the OSD and then select

the Auto Setup Menu. This will access the "Auto Setup Menu" as below.

Follow the on-screen instructions and press 'Enter' on the remote control

when ready to start the Auto Setup function.

Once activated the OSD will display the message below and the word

'AUTOSETUP' will also be displayed on the front panel of the 351R to conrm.

A series of test signals will now be output from all of the connected speaker

terminals of the 351R (including the Subwoofer output).

Once nished the unit will display a screen similar to the one below reporting

which speakers were found and any that appear out of phase.

If any speakers appear unconnected or out of phase carefully check the

connections on the speaker and the back of the unit. Also check any bi-wiring

links that might be present on the speaker. For any out of phase speakers

check that the relevant + terminal of the 351R goes to the + terminal of that

speaker and similarly the – terminal of the 351R goes to the – terminal of the

speaker for that channel.

y O

azur 351R

Audio In. Select

Tone/Sub Config.

Speaker Config.

Speaker Distance

Speaker Level

Speaker Xover

Auto Setup

Dolby/DTS Setup

OSD Setup

Quit : [I/O] Enter : [ENTER]

Please press ENTER to start auto

setup

Auto Setup Menu

Continue : ENTER

Plug the microphone into the Mic. input on the front panel and

place the microphone at normal listening position and height

Auto Setup Menu

The unit is now checking which speakers are connected and their

phase

Please wait...

azur 351R

Continue : ENTER

The speakers that have been found are:

L C R SL SR LB RB SW

All speakers are in phase

If necessary press the button to perform a retest or press Enter to start

the second part of the auto setup procedure as below.

Again a series of test signals will now be output from all of the connected

speaker terminals and subwoofer. The 351R uses these to measure the

levels and distances (and hence introduce the correct delays) appropriate to

your speakers and room characteristics.

When the auto setup of the 351R is completed successfully, the 351R will

return to the Speaker Setup Menu.

The Speaker Distance and Level Calibration settings for each speaker will

have been updated.

It is of course now possible to go into the Speaker Delay and Level Calibration

menus if you want to manually check/adjust the settings made by the

CAMCAS system, and it is always advisable to check them as no system can

be totally foolproof.

To exit the auto setup menu of the 351R continue to press the

button

on the remote control to exit all menus or until 'OSD 'is no longer displayed

on the front panel. You can now unplug the microphone and put it away for

future use.

Note: If the auto setup of the 351R is unsuccessful for some reason a 'Fail'

message will appear on the OSD. Included in this message will be details of

the speaker channel or channels which have not been successfully adjusted.

If this is the case, please again check that the speaker or speakers detailed

in the OSD as 'failed' are connected correctly & have not been wired out of

phase. Also check the microphone connection and any other external issues

that could have affected the tests such as noise in the room etc.

Note: Like all such systems CAMCAS has some limitations. Speakers that

exhibit very strong phase angles or deliberately wire some drive units out of

phase can of course appear to the system as an out of phase speaker when

correctly connected. If a speaker is reported as out of phase but is correctly

wired please consult the speakers manufacturer in case this is the case.

Similarly bi-polar speakers which radiate in more than one direction can

make it difcult to measure the distance and sometimes level accurately as

you might expect.

In all cases it is always advisable to manually check the settings CAMCAS has

made for a 'reality check' to ensure there are no obvious errors.

Auto Setup Menu

The unit is now measuring the Distance and Level settings for

your speakers

Please wait........

azur 351R

Audio In. Select

Tone/Sub Config.

Speaker Config.

Speaker Distance

Speaker Level

Speaker Xover

Auto Setup

Dolby/DTS Setup

OSD Setup

Quit : [I/O] Enter : [ENTER]

Please press ENTER to start auto

setup

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio Azur 351R Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio Azur 351R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info