Bedienungsanleitung Cambridge Audio Azur 551R V2 (Seite 8 von 28) (Englisch)

656752

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Front panel display

Mode icons

Direct indicator – Lights when the 551R V2 is in a Direct mode - Analogue

Stereo Direct or 7.1 Direct.

HDMI – Indicates the current source audio input type is HDMI.

Multi – Indicates the 551R V2 is receiving multi-channel PCM over HDMI.

Digital/Analogue indicators – Indicates whether the current source audio

input type is Digital (S/P DIF/Toslink) or Analogue.

Decoding mode indicators (PCM, Dolby Digital, DTS

etc)

Shows the current decoding mode, Dolby Digital, DTS etc. In conjunction

with the Output Channel indicators these give full details of the current

processing mode.

Main information display

Shows the current source selected, also the surround mode and station

name/frequency when in tuner mode etc.

Output channel indicators

Shows the currently active channels depending on decoding mode and

source material. Icons lit indicate active channels in the source material.

Icons with a box around them indicate actual channels being output by the

551R V2.

Display examples

Indicates a 5.1 Dolby Digital source being played back as 5.0 (Sub off). The

lit LFE indicates a low frequency effects channel is present in the source

material. When this icon isn't boxed it indicates the LFE channel is not being

sent to a subwoofer but will be mixed into the front left and right instead.

Indicates a 7.1 playback of DTS ES material.

Indicates a 2.1 output created in the digital domain from analogue input

material.

To avoid damaging the speakers with a sudden high-level signal, be sure to

switch the power off before connecting the speakers. Check the impedance

of your speakers. Speakers with an impedance of 8 ohms (each) are

recommended.

The coloured speaker terminals are positive (+) and the black speaker

terminals are negative (-). Make sure correct polarity is maintained at each

speaker connector or the sound can become weak and "phasey" with little

bass.

Prepare the speaker cords for connection by stripping off approximately

10mm (3/8") or less (no more than 10mm, as this could cause a short-

circuit) of the outer insulation. Twist the wire tightly together so there are no

loose ends. Unscrew the speaker terminal knob, insert the speaker cable,

tighten the knob and secure the cable.

Note: All connections are made via loudspeaker cable, except if using an

active subwoofer which would be connected via a standard RCA phono cable.

Banana Plugs (4mm standard) connected to the speaker cable are

recommended for direct insertion into the speaker terminals.

Please refer to the 'Speaker Conguration' section of this manual for more

information on 5.1 and 7.1 speaker setups.

Front

speakers

Surround

speakers

Centre speaker

Surround back

speakers

Powered subwoofer

Phono/RCA cable

Loudspeaker connections

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio Azur 551R V2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio Azur 551R V2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info