Bedienungsanleitung Cambridge Audio Azur 752BD (Seite 8 von 40) (Englisch)

497532

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

7. USB port 1 and 2

Port for interfacing to a ash/memory card or Mass Storage Device (such

as a portable hard-drive).

Note:

• This unit supports USB Mass Storage Class Bulk Transport devices

only. Most USB thumb drives, portable hard disk drives and card

readers conform to this device class. Other USB devices such as MP3

players, digital cameras, and mobile phones that include their own

memory management may not be compatible.

• Supported USB drives must be formatted with the FAT (File Allocation

Table), FAT32 or NTFS (New Technology File System) le system.

• In some cases, an incompatible USB device may cause the player to

stop responding. If this occurs simply turn off the power, remove the

USB device, and turn the player back on.

• The player accesses the USB drive in read-only mode. In order to

minimize the risk of data corruption, it is recommended that you only

unplug the USB device when playback has completely stopped.

8. IR (Infra-Red) emitter in

Allows modulated IR commands from multi-room systems or IR repeater

systems to be received by the unit.

9. RS232C

Used for control of the 752BD in Custom Install situations. A full protocol

is available for the 752BD on our website.

10. 7.1 channel analogue audio output

If Down-mix is set to "7.1 CH" in the Speaker Setup page (Down-mix mode

section) of the 752BD’s Setup menus, these sockets provide 7.1 output

from the 752BD’s built in Surround-Sound decoder. This can be used to

connect to the 7.1 audio line-level inputs of an amplier/AV receiver or

amplied speaker package if required. Similarly, Down-mix can be set

to "5.1 CH" to provide 5.1 output. If Down-mix is set to "LT/RT", "Stereo"

or "V.Surround" the Left and Right outputs only are active and provide a

stereo or stereo downmixed output. Refer to the "Speaker conguration"

section of this manual for more information.

11. Digital input

Optical and Coaxial digital audio inputs, used to connect to:

Toslink Optical - Use a high quality TOSLINK bre optic cable.

S/P DIF Co-Axial Digital - Use a high quality 75 ohm digital RCA/Phono

interconnect cable designed specically for digital audio use.

12. Stereo audio out

Permanent stereo outputs for use with Stereo material.

13. AC power socket

Once you have made all audio and video connections, plug the IEC type

AC power cable into the rear of the unit and an appropriate mains socket

then switch on. Your 752BD is now ready for use.

Rear panel connections

1. Ethernet LAN port

Used for Playback of context from the Internet or Network attached

storage drives and servers, also used for discs supporting BD-Live that

provide interactive features when the player is connected to the Internet.

2. HDMI input

This input is used to connect to a source device such as a set-top box or

other HDMI Source.

3. Diagnostic video

Use for diagnostic purposes. Connect to a TV/Monitor via a 75 ohms

RCA/Phono cable designed specically for video use.

4. Digital outputs

Optical and Coaxial digital audio outputs, optionally used to connect to

a suitable Audio/Video Receiver for surround sound decoding (output

must be set for "Bitstream" - refer to the "Audio setup" section). HDMI is

however the preferred correction to AV Receivers as the latest lossless

CODECS are only supported over HDMI. These outputs can also be used

to connect to a separate DAC or digital recording device (output must be

set for "LPCM" - refer to the "Audio setup" section).

Toslink Optical - Use a high quality TOSLINK bre optic cable.

S/P DIF Co-Axial Digital - Use a high quality 75 ohm digital RCA/Phono

interconnect cable designed specically for digital audio use.

5. HDMI output 2

Secondary HDMI output. Both outputs 1 and 2 can be used at the same

time to send the same audio/video to two displays (with both being 3D

TV compatible) or to send audio over one HDMI link and video over the

other.

Always use a "HDMI 1.4 High Speed" certied Cable.

HDMI 1 and 2 both support Audio Return Channel from TVs that have this

function. See later section.

6. HDMI output 1 (primary output)

The HDMI (High-Denition Multi-Media Interface) is a purely digital

connection that can carry both audio and video. Use a dedicated HDMI

cable to connect to a TV/Monitor or AV Receiver with a compatible HDMI

input.

Always use a "HDMI 1.4 High Speed" certied Cable.

This output is the primary output and benets from the Marvell QDEO

video processor. Both this output and output 2 are 3D TV compatible.

HDMI 1 and 2 both support Audio Return Channel from TVs that have this

function. See later section.

8 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio Azur 752BD Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio Azur 752BD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info