Bedienungsanleitung Cambridge Audio CXR120 (Seite 16 von 17) (Englisch)

656750

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

DTS-HD speaker re-map

When playing back a DTS-HD track the CXR can electronically reposition

your speakers to match the setup used in the original recording studio. This

is done automatically in most cases, but for 7.1 setups you will need to

choose either option 1 or 5 – whichever most closely resembles your actual

speaker layout.

Conguration 1 – 7.1 channel: L, C, R, LFE, Ls, Rs, Lsr, Rsr

Center

Right (30°)

Left (30°)

Left Surround (110°)

Left Surround Rear

(150°)

Right Surround Rear

(150°)

Right Surround

(110°)

LFE

Conguration 5 – 7.1 channel: L, C, R, LFE, Lss, Rss, Lsr, Rsr

Center

Right (30°)

Left (30°)

Left Surround Side

(90°)

Left Surround Rear

(150°)

Right Surround Rear

(150°)

Right Surround

Side (90°)

LFE

Trigger outputs

The outputs are 0V for O and 12V for On at up to 100mA. The connections

are 3.5mm mono mini-jacks, with the tip as the output, ring as ground.

The options are:

Manual Select: Trigger output is toggled On/O by the matching Trigger

button on the remote control.

Follow Standby: The trigger output will follow the On/O status of the unit.

Sources: – The trigger output is linked to a specic source.

SW version

All 4 software version numbers need to be stated when contacting Cambridge

Audio customer support.

Update via USB

The CXR software can be updated from the front panel USB socket, which

would normally only be required by a service department or where a network

is not available. Normally user updates will be via a network connection.

Save current settings

Saves settings to internal memory. If the current settings have not been

saved, it is advisable to save the current settings before a software update

is performed.

Load saved settings

Loads the stored settings.

Factory reset

After a factory reset any saved settings can be restored if desired.

Network software update

The CXR can be updated via the StreamMagic module connected to the

internet. Updates of the StreamMagic module itself can only be started from

the Cambridge Connect app or the Web administration interface.

Note: A full update can take over 45 minutes to complete.

Web administration interface

This interface allows the user to:

- Customise the name displayed in the Players list in the Cambridge Connect

app and in the Spotify Connect device list.

- Setup the wireless network connection.

- Upgrade the CXR's rmware.

Wired connection

Connect the CXR to a wired network and nd the IP address in the 'CXR

Setup Menu'.

CXR Setup Menu

Speaker Setup

Input Setup

Zone 2 Settings

Network Setup

General Settings

HDMI Output Setup

Advanced Setup

Connection Information

Network Selection

IP Adress

Subnet Mask

Gateway

DNS1

Ethernet

192.168.0.127

0.0.0.0

Use a web browser on the same network to connect to the CXR IP address,

eg http://192.168.0.127/

Wireless connection

Plug in the supplied wireless antenna to the USB socket on the rear of the

CXR.

Go to your computer/tablet and click on the Wi-Fi/network logo and select

CXR.

Use a web browser on your device to connect to http://10.10.10.10/

HDMI output setup cont.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio CXR120 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio CXR120

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info