Bedienungsanleitung Cambridge Audio AZUR 851E (Seite 6 von 16) (Englisch)

656741

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Volume

ModePhonesStandby / On

azur 851E

Pre-Amplifier

Bass Treble Direct

Front panel controls

Standby/On

Switches the unit between Standby mode (indicated by dim power LED)

and On (indicated by bright power LED). Standby is a low power mode

where the power consumption is less than 0.5 Watts. The unit can be

left in Standby mode when not in use. If the unit is not going to be used

for a long period of time it should be switched off via the Power On/Off

switch on the rear panel.

Note: As default the 851E ramps the volume up or down when switched

on and when going into Standby mode. This feature can be turned off if

desired; please refer to the 'Pre-amplier setup' section of this manual

for more information.

Phones

Allows for the connection of stereo headphones with a ¼" Jack plug.

Headphones with an impedance of between 32 and 600 ohms are

recommended. When the headphones are connected, the loudspeaker

relays are released switching off the output to the loudspeakers.

IMPORTANT! Do not use headphones that exceed a 3 meter cable.

Mode

Press to switch between Volume and Balance modes. Press and hold to

enter the 851E System Congure menu.

Infrared sensor

Receives IR commands from the supplied Azur remote control. A clear

unobstructed line of sight between the remote control and the sensor

is required.

Source select buttons

Push the appropriate input selection button to select the source

component that you wish to listen to (highlighted by a solid circle on the

display). The signal selected is also fed to the Rec Out sockets so that it

may be recorded. The input should not be changed whilst recording (but

the recorded signal can be checked using the Rec input).

Note:

– Repeatedly pressing the Source 1, 2 or 3 buttons will toggle these

inputs between 'Balanced' and 'Unbalanced' source input.

– The solid circle will ash if there are no input signals detected.

Display

LCD used to control the 851E. Please refer to the 'Operating instructions'

and 'Pre-amplier setup' section of this manual for more information.

Bass and Treble

Press to release and rotate to allow subtle adjustments to the tonal

balance of the sound.

Direct

This control gives the audio signal a more direct path by bypassing the

tone control circuits for the purest possible sound quality.

The Bass/Treble icon (

) appears in the display when the bass

and treble circuit is active (in circuit) and is not present when they are

bypassed.

Note: Direct can be set on or off individually for each input. This setting

is recalled each time a source is selected.

Volume

Use to increase/decrease the level of the sound from the outputs of the

pre-amplier. This control affects the level of the loudspeaker output,

the pre-amp output and the headphone output. It does not affect the

Rec Out connection.

The Volume control is also used in navigating the 851E System Congure

menus on the front panel display.

Please refer to the 'Operating instructions' section of this manual for

more information on some functions of these buttons.

1 2 3 4

5 6

8 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio AZUR 851E Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio AZUR 851E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info