Bedienungsanleitung Canon LX-MU700 (Seite 3 von 90) (Englisch)

709684

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

♦ Projector Installation Notice

■ Place the projector in a horizontal position

If installing the projector on the oor or hanging from the ceiling, the left /right inclination of the

projector should be no more than 10 degrees. An inclination of more than 10 degrees may damage

the lamp.

■ Allow at least 70 cm clearance around the exhaust vent.

■ Ensure that the intake vents do not recycle hot air from the exhaust vent.

■ When operating the projector in an enclosed space, ensure that the surrounding air temperature

within the enclosure does not exceed operation temperature while the projector is running, and the

air intake and exhaust vents are unobstructed.

♦ Verify Installation Location

■ Turn on Altitude Mode when located in high altitude areas.

■ The projector can only be installed upright or inverted.

■ When installation the bracket, make sure the weight limit is not exceed and rmly secured.

■ Avoid installing at high temperature, insufcient cooling and heavy dust locations.

■ Keep your product away from uorescent lamps to avoid malfunction caused by IR interference.

■ The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted

tightly, with the screws on both sides securely fastened to ensure proper connection of the signal

wire for achieving optimal display effect.

■ The power cord and signal cable should be connected before power on the projector. During the

projector starting and operating process, DO NOT insert or remove the signal cable or the power

cord to avoid damaging the projector.

♦ Cooling notes

Air outlet

■ Air outlet location should not be in front of the lens of other projector to avoid causing illusions.

■ Keep the outlet at least 70 cm away from the inlets of other projectors.

■ The projector generates a massive amount of heat during use. The internal fan dissipates the heat

of the projector when shutting down, and such process may continue for a certain period. After

the project enters STANDBY MODE status, press the AC power button to turn off the projector

and remove the power cord. DO NOT remove the power cord during the shutdown process, as it

may cause damage to the projector. In the meantime, the delayed heat radiating will also affect

the service life of the projector. The shutdown process may vary depending on the model used.

Whatever the case may be, be sure to disconnect the power cord till after the projector enters the

STANDBY status.

Air inlet

■ Make sure there is no object blocking air input within 50 cm.

■ Keep the inlet away from other heat sources.

■ Avoided heavy dust area.

♦ Power Safety

■ Only use the supplied power cord.

■ Do not place anything on the power cord. Place the power cord where it will not be in the way of

foot trafc.

■ Remove the batteries from the remote control when storing or not in use for a prolonged period.

■ The wall outlet must be able to meet the power demands of the device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon LX-MU700 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon LX-MU700

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info