470067

Carrera Digital 132 - 30154 FORMULA 1 Champions Seite 5

5
Zoom out
Zoom in
Vorherige Seite
1/7
Nächste Seite
10
Preparation of start and
points function
Make sure that the car’s guide keel is located inside the
track slot and that the double sliding contact is in contact with the
current carrying track.
Place the cars onto the connecting track.


Race modes

1. Switch on the Black Box (ON-OFF)
2. After approx. 1 second the central LED will illuminate perma-
nently and a brief acoustic signal will sound.
3. Position the car/s on the connecting track
4. In training mode, the track is released without signal from the
trac light; you can start immediately

1. Switch on the Black Box (ON-OFF)
2. After approx. 1 second the central LED will illuminate perma-
nently and a brief acoustic signal will sound.
3. Afterwards, press the start button until all LEDs light up
4. Position the car/s on the connecting track
5. Press the start button again – the starting sequence will be initi-
ated, the LEDs will illuminate and acoustic signals will sound.
6. Once the trac light phase has expired (LEDs light up individu-
ally), the race is released
7. False start: If a car’s speed controller is actuated during the trac
light phase, this is rated as false start. The vehicle that has caused
the false start will travel a short distance and the LED on the rel-
evant vehicle or hand control will ash. The race is not released and
the start has to be repeated.
Light function on/off
3 sec.
STOP
The car programmed to the speed controller will have to come to a
stop for at least 3 seconds before the light can be switched on or o
by the push of the lane-change-button.
Operating 6 cars
1
Plug speed controller extension set (item no. 30348) in connector 1
of the Black Box. For next steps see section „Coding of cars to the
according speed controller“.
Coding/decoding of the cars to
the according speed controller
2x CLICK
2x CLICK
Place car on the track, push lane-change-button twice g.
, lift car
at the front, put car back again g.
, while car´s lights are ashing
push lane-change-button twice g.
. Programming is conrmed
by a tone. All settings are saved until new programming is carried
out.
Autonomous Car function
300
15 0
250
200
0
100
50
2x CLICK
4x CLICK
SPEED
+
CLICK
Place car on the track, push lane-change-button twice, lift car at the
front, put car back again (see coding/decoding g. 1 + 2). While
car´s lights are ashing push lane-change-button 4 times g.
.
Start car, push lane-change-button for requested speed g.
(ir-
respective of the car´s position). Autonomous car will drive at this
speed automatically and consistently until its decoding.
Decoding is eected by holding the car. For new coding see coding/
decoding.
Pace Car function
Pit Stop 30346
2x CLICK
300
15 0
250
200
0
100
50
6x CLICK
SPEED
+
CLICK
Place car on the track, push lane-change-button twice, lift car at the
front, put car back again (see coding/decoding g. 1 + 2).
While car´s lights are ashing push lane-change-button 6 times g.
Start car, push lane-change-button for requested speed g.
(irrespective of the car´s position). Car will assume this speed con-
sistently and will enter the next Pit Stop automatically g.
.

Start Pace Car by pushing the button at the Black Box g.
. After
10 seconds each lane switch will change independently until the
Pace Car enters the Pit Stop. Carry out car decoding (see point
coding/decoding).
Setting basic speed
1

1 – 10
1 – 10
(individually for one and/or several cars)
Plug any speed controller in connector 1. Switch o Black Box,
place car/s on the track, push lane-change-button and keep it
pushed while Black Box is switched on again. Don´t release the
lane-change-button until the 1st LED lights red. Levels are set by
pushing lane-change-button. Conrm speed by pressing the speed
controller´s tappet (thumb) (=> middle LED will light).
1 LED on = low speed
5 LEDs on = high speed
Setting braking effect
2

1 – 10
1 – 10
(individually for one and/or several cars)
Plug any speed controller in connector 2. Switch o Black Box,
place car/s on the track, push lane-change-button and keep it
pushed while Black Box is switched on again. Don´t release the
lane-change-button until the 1st LED lights red. Levels are set by
pushing lane-change-button. Conrm braking eect by pressing
speed controller´s tappet (thumb) (=> middle LED will light). Before
the start return speed controller to the original connector!
1 LED on = low braking eect
5 LEDs on = high braking eec
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Carrera Digital 132 - 30154 FORMULA 1 Champions wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info