Bedienungsanleitung Carrera Evolution - 25179 WORLD GRAND PRIX Disney Cars (Seite 4 von 5) (Englisch)

469938

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

Preparation of start

1 2

This Carrera Evolution vehicle ideally matches the Carrera track

system scale 1:24.

Make sure that the car’s guide keel is located inside the track

slot and that the double sliding contact is in contact with the current

carrying track. Place the cars onto the connecting track.

Optimally setting up the grinders:

To ensure proper and continuous driving, slightly fan out the ends

of the contact brushes

and bend them towards the track as per

g.

. Only the end of the contact brush should have contact to the

track and may be cut o slightly in case of wear. Dust and abrasion

should be removed from track material and sliding contacts from

time to time.

During operation small car parts as spoilers or mirrors may get o or

brake due to being original detailed parts of the car model. To avoid

this it is possible to remove them before operation.

Change of running direction

This is necessary and/or possible in case the running direction shall

be changed. Therefore the reversing switch at the car’s bottom side

has to be positioned accordingly.

Maintenance and care

To ensure a proper operation of the motor-racing circuit, all race-

track components should be regularly cleaned. Pull the plug prior to

cleaning.

Racetrack: Keep the track surface and track slots clean with a

dry cloth. Do not use any solvents or chemicals for cleaning. When

it is not in use, store the racetrack in a clean and dust-protected

location, preferably in the original cardboard box.

Car check: Clean axle and wheel bearings, pinion gears, gear-

wheels and bearings and lubricate using a resin- and acid-free

grease. You can use a toothpick or similar as aid. Regularly check

the condition of sliding contacts and tyres.

Replacement of double sliding

contact and guide keel

2 a 2 b

Advice:

• It is recommended to always take out and change only one

grinder.

• Never pull the vehicle backwards, because the grinders could be

damaged otherwise.

Please carefully pull out the guide keel according to g.

When changing the double contact brushes please take

care that in stage one the upper contact brush

is only

pulled out partly and that in stage two the double contact brush can

be pulled out completely with the contact brush

. For inserting

please proceed the same way.

Changing the rear axle

2 3

Take o the vehicle´s upper part from the chassis as per g.

Remove the axles from the bearings positions with pressure (

Insert new axle. Pay attention to the correct position of the axle

bearings (

Troubleshooting

Driving tips

Troubleshooting:

In case of any malfunctions, please check the following:

• Has the connection to the power supply been established

correctly?

• Have transformer and speed controllers been connected

correctly?

• Are the track connections faultless?

• Are the racetrack and track slots clean and free of any foreign

objects?

• Are the sliding contacts in order and do they make contact with

the track slot?

Driving technique:

• You can drive fast along the straight track but you should brake

before the curve and then accelerate again when coming out of the

curve.

• Do not fasten or block the vehicles when the motor is running:

overheating or damage to the motor could result otherwise.

Note: When using track systems which are not manufactured by

Carrera the existing guide keel has to be replaced by the special

guide keel (#85309). While using the Carrera crossing (#20587) or

high banked curve 1/30° (#20574) slight driving noise might occur

which is due to the full-scale genuineness and does not aect aw-

less operation.

All Carrera spare parts are available in the webshop:

carrera-toys.com

Delivery exclusively to Germany, Austria, Netherlands, Belgium and

Luxembourg.

Technical specifications

Output voltage: Toy transformer

14,8 V

2 x 14,8 VA

Electricity modes

1.) Operating mode = cars are operated via speed controllers

2.) Idle mode / Stand-by mode = speed controllers are not activated,

no game

CURRENT CONSUMPTION

< 1 watt / 1w

3.) O-state = power supply unit disconnected from mains supply

This device is marked by “selective sort throught” symbol related to

sort through domestic, electric and electronic, waste.

This means the product must be treated by a specialized “sorting/

collecting” system in accordance with European directive 2002/96/

CE, to reduce the impact upon environment.

For more precise information, please contact your local administra-

tion.

Electronical product which are not going through special collect-

ing, are potentially dangerous for environment and human health,

because of dangerous substance.

Output voltage: Toy transformer

14,8 V 2 x 14,8 VA

Electricity modes

1.) Operating mode = cars are operated via speed controllers

2.) Idle mode / Stand-by mode = speed controllers are not activated,

no game CURRENT CONSUMPTION

< 1 watt / 1w

3.) O-state = power supply unit disconnected from mains supply

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carrera Evolution - 25179 WORLD GRAND PRIX Disney Cars Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info