Bedienungsanleitung Carrier 38NY009 (Seite 5 von 9) (Englisch)

481299

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

Projection

15 mm or less

Anchor bolt

Clip anchor

(local parts)

5 mm dia. hole

Mounting screw

Ø4 x 25 R

Installation plate

(Keep horizontal direction.)

5 mm dia. hole

Clip anchor

(local parts)

Mounting screw

Ø4 x 25R

Anchor bolt

Projection

15 mm or less

INDOOR UNITINDOOR UNIT

Installation Place

• A place which provides the spaces around the indoor unit as shown in the

diagram

• A place where there are no obstacles near the air inlet and outlet

• A place which allows easy installation of the piping to the outdoor unit

• A place which allows the front panel to be opened

• The indoor unit shall be installed as top of the indoor unit comes to at least

2 m height. Also, it must be avoided to put anything on the top of the indoor

unit.

• Direct sunlight to the indoor unit’s wireless receiver should be avoided.

• The microprocessor in the indoor unit should not be too close to RF noise

sources.

(For details, see the owner’s manual.)

Remote control

• A place where there are no obstacles such as a curtain that may block the

signal from the indoor unit

• Do not install the remote control in a place exposed to direct sunlight or close

to a heating source such as a stove.

• Keep the remote control at least 1 m apart from the nearest TV set or stereo

equipment. (This is necessary to prevent image disturbances or noise inter-

ference.)

• The location of the remote control should be determined as shown below.

Cutting a Hole and Mounting

Installation Plate

NOTE

• When drilling a wall that contains a metal lath, wire lath or metal plate, be

sure to use a pipe hole brim ring sold separately.

Cutting a hole

When installing the refrigerant pipes from the rear

1. After determining the pipe hole position on the mounting plate (∆), drill the

pipe hole (Ø65 mm) at a slight downward slant to the outdoor side.

CAUTION

54 °

5°

(Side view) (Top view)

Indoor unit

Reception range

Remote

control

Remote

control

Reception

range

Indoor unit

65 mm

100 mm

80 100 180

42NQ012

The center of the pipe hole

is above the arrow.

Pipe hole

90 mm

66 mm

42 mm

The center of the pipe hole is above the arrow.

Pipe hole

42NQ009

Mounting the installation plate

Anchor bolt holes

Hook

Pipe hole

Installation

plate

Mounting screw

Weight

Indoor unit

Thread

2 m or more from ﬂ oor

42NQ009

42NQ012

A 35 mm 62 mm

B 55.5 mm 82.5 mm

C 120 mm 170 mm

D 65 mm 85 mm

When the installation plate is directly mounted

on the wall

1. Securely ﬁ t the installation plate onto the wall by screwing it in the upper and

lower parts to hook up the indoor unit.

2. To mount the installation plate on a concrete wall with anchor bolts, use the

anchor bolt holes as illustrated in the below ﬁ gure.

3. Install the installation plate horizontally in the wall.

CAUTION

Electrical Work

1. The supply voltage must be the same as the rated voltage of the air condi-

tioner.

2. Prepare the power source for exclusive use with the air conditioner.

NOTE

• Wire type : More than H07RN-F or 245 IEC66

Failure to ﬁ rmly install the unit may result in personal injury and property

damage if the unit falls.

• In case of block, brick, concrete or similar type walls, make 5 mm dia. holes

in the wall.

• Insert clip anchors for appropriate mounting screws 7.

NOTE

• Secure four corners and lower parts of the installation plate with 4 to 6

mounting screws to install it.

CAUTION

NOTE

• Ensure all wiring is used within its electrical rating.

• This appliance can be connected to the mains in either of the following

two ways.

(1) Connection to ﬁ xed wiring:

A switch or circuit breaker which disconnects all poles and has a

contact separation of at least 3 mm must be incorporated in the ﬁ xed

wiring. An approved circuit breaker or switches must be used.

(2) Connection with power supply plug:

Attach power supply plug with power cord and plug it into wall outlet.

An approved power supply cord and plug must be used.

CAUTION

Model 42NQ009 42NQ012

Power source 50Hz, 220 – 240 V Single phase

Maximum running current 7.5A 12A

Plug socket & fuse rating 16A

Power cord 1 mm

or more 1.5 mm

or more

When installing the installation plate with a mounting screw, do not use

the anchor bolt holes. Otherwise, the unit may fall down and result in

personal injury and property damage.

For the air conditioner that does not have power cord, connect a power

cord to it as mentioned below.

(1) Open the air inlet grille upward.

(2) Remove the two screws securing the front panel.

How to connect the power cord

1110251161-EN.indd 31110251161-EN.indd 3 12/28/07 6:10:49 PM12/28/07 6:10:49 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carrier 38NY009 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Carrier 38NY009

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info