Bedienungsanleitung Carrier 42 HQX (Seite 8 von 12) (Holländisch)

481328

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

42 HWX / HQX

GB - 7

ENGLISH

Start/stop

(button B)

When the air conditioner is not in operation, the controller readout

will display the time of day only (in case other symbols are lit, turn

controller off by pressing button B

Press button B

to start the air conditioner; indicator N on the

unit will appear and be illuminated.

All selected and memorized functions will light up and appear; the

unit will operate according to the functions selected.

If the unit does not acknowledge the starting signal by emitting a

sound (“beep”) and indicator N

does not light up, it is necessary

to turn the controller off by pressing button B

and then repeat the

operation.

Press button B

to stop the air conditioner. All indicators on the

unit will go out, and controller will display only the current time.

If the unit does not stop, turn the controller on (by pressing button B

) and repeat the operation. In some special operating conditions

the fan will continue to run for 30 sec. after the unit stops; the

indicator Q

on the unit will lighten.

If button B

(air conditioner starting) is pressed too soon after a

stop, the compressor will not start for 3 minutes due to the inherent

protection against frequent compressor cycling; in this case

indicator Q on the unit will also light up.

The unit will only emit a “beep”, when the signals are received

correctly.

Timer mode on/off

(button C)

Press this button when you want the air conditioner to operate in

the timer mode according to the time programs selected with button

When this function is on, indicator P

on the unit is lit.

After a power failure, indicator P

will flash and the unit will run in

the last operating condition before the power cut.

Power failures will deactivate the Timer mode: to reactivate the

Timer mode, press button C

twice.

Selection of the operating mode

(button D)

With this button the operating mode of the air conditioner can be

selected. Different options are available depending on the unit

model. By repeatedly pressing this button the available modes will

be selected in sequence and the relevant symbols will appear on

the display, while the unit will acknowledge signal receipt with a

confirming beep.

Symbol on display

Cooling with dehumidification.

Heating (where available).

Automatic mode.

The air conditioner will automatically switch from heating

(where available) to cooling and vice versa in order to

maintain the selected temperature.

Dehumidification only.

The air conditioner extracts moisture from the air without

sensibly changing the room temperature.

Ventilation (fan only)

Use of the remote controller

Setting desired temperature

(button E)

DOWN

(button F)

Pressing the UP (E ) and DOWN (F ) buttons will increase or

decrease the temperature set from the previously set value. The

unit will confirm signal receipt with a beep, and the value of the set

temperature on the display will change accordingly.

The temperature can be set between 18°C and 29°C at 1 degree

intervals.

In the cooling mode, if the temperature selected is higher than the

room temperature the unit will not start; the same applies for the

heating mode, if the selected temperature is lower than the room

temperature.

Setting the timer programs

(button G)

By pressing button G it is possible to choose one of the following

programs in sequence:

Symbol on display

No Continuous operation

simbol (timer off)

Start time program

Stop time program

Combined program: unit will automatically cycle on and off

as programmed

Set start time

Press button G

until the symbol indicating unit start program will

appear on display under the word TIMER.

• The time appearing on display shows the starting hour

previously programmed:

• You can set your personalized new start time by pressing buttons

and I until the desired time appears. Each press of the

button will change the time up or down by 15 min. between 0:00

and 23:45.

Press button C

to confirm your selection: indicator P on the

unit will light up and the air conditioner is ready to start at the

selected time.

If the unit is in operation when you send your confirmation by

pressing button C

, it will turn off and

restart at the time now programmed.

Set stop time

Press button G

until the symbol indicating unit stop program

appears on the display under the word TIMER. The time appearing

on display shows the stop time previously programmed; you can

now set your personalized new stop time by proceeding as for the

start time.If the unit is turned off when you send your program

confirmation by pressing button C

, it will start up, and then turn

off at the time now programmed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carrier 42 HQX Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info