466629
5
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
2271-5
Deleting an Altitude Measurement Record
Use the Recall Mode to delete altitude measurement records. You can enter
the Recall Mode by pressing D.
Note
The procedure you should use to delete a record depends on if the record
was produced by Auto measurement or Manual measurement.
Deleting Auto measurement records deletes the entire set, from the initial
record to the final record.
You cannot delete a record that is part of an ongoing Auto measurement
operation (indicated when AUTO is flashing on the display). You can,
however, delete records from another, already completed measurement
operation.
To delete a altitude measurement record
1. In the Recall Mode, display the record you
want to delete.
If you want to delete a set of Auto
measurement records, display the first
record of the set.
2. To clear the data, hold down A until the
watch emits a long beep (and until
CLR
stops flashing on the display).
First record of the set
ALARM
You can set five independent Daily Alarms.
When an alarm is turned on, the alarm tone
sounds when the alarm time is reached. You
can also turn on an Hourly Time Signal that
causes the watch to beep twice every hour on
the hour.
The alarm number (
1 through 5) indicates
an alarm screen.
SIG appears in place of
AL when the Hourly Time Signal screen is
shown.
All of the operations in this section are
performed in the Alarm Mode, which you
enter by pressing D.
To set an alarm time
1. In the Alarm Mode, use E and B to
select the alarm whose time you want to
set.
2. Hold down A until the hour digits of the alarm time start to flash, which
indicates the setting screen.
This automatically turns on the alarm.
3. Press D to move the flashing between the hour and minutes.
4. While a setting is flashing, use E (+) and B () to change it.
When setting the alarm time using the 12-hour format, take care to set
the time correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Time (Hour : Minutes)
Alarm on indicator
Timekeeping Mode time
Alarm number
AL-1
SIG
AL-2
AL-5
AL-3
AL-4
Press E.
Press B.
Alarm Operation
The alarm sounds at the preset time for about 20 seconds (in all modes), or
until you stop it by pressing any button.
To test the alarm
In the Alarm Mode, hold down C to sound the alarm.
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use E and B to select an alarm or the Hourly Time
Signal.
2. When the alarm or the Hourly Time Signal you want to is selected, press
C to turn it on and off.
Indicates alarm is ON.
Indicates Hourly Time Signal is ON.
The alarm on indicator (
) and the Hourly Time Signal on indicator
(
) are shown on the display in all modes while these functions are
turned on.
If any alarm is on, the alarm on indicator is shown on the display in all
modes.
Start Stop Re-start Stop Clear
Split releaseStart Split Stop Clear
Start Split
First runner
finishes.
Stop
Second runner finishes.
Record time of first
runner.
Split release
Record time of
second runner.
Clear
EE E E B
EB B E B
EB E B B
STOPWATCH
The stopwatch lets you measure elapsed time,
split times, and two finishes.
The display range of the stopwatch is 23
hours, 59 minutes, 59.99 seconds.
The stopwatch continues to run, restarting
from zero after it reaches its limit, until you
stop it.
The stopwatch measurement operation
continues even if you exit the Stopwatch
Mode.
All of the operations in this section are
performed in the Stopwatch Mode, which
you enter by pressing D.
To measure times with the stopwatch
Elapsed Time
Split Time
Two Finishes
Hours
Minutes
1/100 second
Seconds
BACKLIGHT
The backlight uses an EL (electro-
luminescent) panel that causes the entire
display to glow for easy reading in the dark.
The watchs auto light switch automatically
turns on the backlight when you angle the
watch towards your face.
The auto light switch must be turned on
(indicated by the auto light switch on
indicator) for it to operate.
See Backlight Precautions for other
important information about using the
backlight.
To turn on the backlight manually
In any mode, press L to illuminate the display for about one second.
The above operation turns on the backlight regardless of the current auto
light switch setting.
About the Auto Light Switch
Turning on the auto light switch causes the backlight to turn on for about one
second, whenever you position your wrist as described below in any mode.
Be sure to wear the watch on the outside of your left wrist while using the
auto light switch.
Moving the watch to a position that is parallel to the ground and then tilting
it towards you more than 40 degrees causes the backlight to turn on.
Warning!
Always make sure you are in a safe place whenever you are reading
the display of the watch using the auto light switch. Be especially
careful when running or engaged in any other activity that can result
in accident or injury. Also take care that sudden illumination by the
auto light switch does not surprise or distract others around you.
When you are wearing the watch, make sure that its auto light switch
is turned off before riding on a bicycle or operating a motorcycle or
any other motor vehicle. Sudden and unintended operation of the
auto light switch can create a distraction, which can result in a traffic
accident and serious personal injury.
Auto light switch on indicator
Parallel to
ground
More than
40
°
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Casio 2271 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Casio 2271

Casio 2271 Bedienungsanleitung - Deutsch - 14 seiten

Casio 2271 Bedienungsanleitung - Holländisch - 8 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info