Bedienungsanleitung Casio 2894 (Seite 1 von 12) (Englisch)

466630

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Operation Guide 2894

MO0412-EA

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out

of your purchase, be sure to read this manual carefully and keep it on hand

for later reference when necessary.

Applications

The built-in sensors of this watch measure direction, barometric pressure,

temperature and altitude. Measured values are then shown on the display.

Such features make this watch useful when hiking, mountain climbing, or

when engaging in other such outdoor activities.

Keep the watch exposed to bright light

The electricity generated by the solar cell of the

watch is stored by a built-in battery. Leaving or

using the watch where it is not exposed to light

causes the battery to run down. Make sure the

watch is exposed to light as much as possible.

• When you are not wearing the watch on your

wrist, position the face so it is pointed at a

source of bright light.

• You should try to keep the watch outside of

your sleeve as much as possible. Even if the

face of the watch is only partially blocked from

light, charging will be reduced significantly.

Bright light

Solar cell

• Frequent display illumination can run down the battery quickly and require

charging. The following guidelines give an idea of the charging time

required to recover from a single illumination operation.

Approximately 5 minutes exposure to bright sunlight coming in through a

window

Approximately 50 minutes exposure to indoor fluorescent lighting

• Be sure to read “Power Supply” for important information you need to

know when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving

function has turned off the display to conserve power.

• See “Power Saving” for more information.

• The watch continues to operate, even when it is not exposed to light.

Leaving the watch in the dark can cause the battery to run down, which will

cause some watch functions to be disabled. If the battery goes dead, you

will have to re-configure watch settings after recharging. To ensure normal

watch operation, be sure to keep it exposed to light as much as possible.

Bright light

Electrical

energy

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Solar cell

(Converts light to

electrical power.)

Rechargeable battery

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Some

functions

disabled

Dis-

charge

Battery charges in the light. Battery discharges in the dark.

Warning!

• The measurement functions built into this watch are not intended for

taking measurements that require professional or industrial precision.

Values produced by this watch should be considered as reasonable

representations only.

• When engaging in mountain climbing or other activities in which losing

your way can create a dangerous or life-threatening situation, always be

sure to use a second compass to confirm direction readings.

• CASIO COMPUTER CO., LTD. assumes no responsibility for any loss,

or any claims by third parties that may arise through the use of this

watch.

About This Manual

• Button operations are indicated using the

letters shown in the illustration.

• Each section of this manual provides you with

the information you need to perform operations

in each mode. Further details and technical

information can be found in the “Reference”

section.

(Light)

General Guide

• The illustration below shows which buttons you need to press to navigate

between modes.

• In any mode, press L to illuminate the display.

• You can use buttons A, B, and C to directly enter a sensor mode from

the Timekeeping Mode or from another sensor mode. To enter a sensor

mode from the Data Recall, World Time, Stopwatch, Countdown Timer, or

Alarm Mode, first enter the Timekeeping Mode and then press the

applicable button.

Timekeeping Mode

Altimeter Mode

World Time

Mode

Data Recall

Mode

Digital

Compass Mode

Press D.

▲

Press B.

Countdown

Timer Mode

Press D.

▲

Press A.

▲

Sensor Modes

▲

Stopwatch Mode

▲

Barometer/

Thermometer Mode

Press C.

Alarm Mode

▲

Timekeeping

Use the Timekeeping Mode to set and view the

current time and date.

• In the Timekeeping Mode, press E to toggle

between the month–day and the day of the

week at the top of the display.

Read This Before You Set the Time and

Date!

This watch is preset with a number of city codes,

each of which represents the time zone where

that city is located. When setting the time, it is

important that you select the correct city code for

your Home City (the city where you normally use

the watch). If your location is not included in the

preset city codes, select the preset city code that

is in the same time zone as your location.

Hour : Minutes

PM indicator

Seconds

Month – Day

Day of week

Press E.

• Note that all of the times for the World Time Mode city codes are displayed

in accordance with the time and date settings you configure in the

Timekeeping Mode.

• After you correctly set your Home City time and date, you can set the watch

up for timekeeping with a different city code simply by changing the Home

City code in the Timekeeping Mode.

To set the time and date

1. In the Timekeeping Mode, hold down E until the city code starts to flash,

which indicates the setting screen.

2. Use C and A to select the city code you want.

• Make sure you select your Home City code before changing any other

setting.

• For full information on city codes, see the “City Code Table”.

• The actual level at which some functions are disabled depends on the

watch model.

Casio 2894 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Casio 2894

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info