586707

Casio 4713 Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/5
Nächste Seite
Operation Guide 4709 4713
1
MO0907-EB
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
Expose the watch to bright light to charge its battery before using it.
You can use this watch even as its battery is being charged by exposure to bright light.
• Be sure to read “Power Supply” of this manual for important information you
need to know when exposing the watch to bright light.
Keep the watch exposed to bright light
The electricity generated by the solar cell of the watch is
stored by a built-in battery. Leaving or using the watch where
it is not exposed to light causes the battery to run down.
Make sure the watch is exposed to light as much as possible.
•
When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright light.
• You should try to keep the watch outside of your sleeve
as much as possible. Charging is reduced significantly if
the face is only partially covered.
l
l
l
l
l
l
l
l
l
l
l
Bright Light
Solar cell
• The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will result in some watch
functions to be disabled. If the battery goes dead, you will have to re-configure watch
settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
All
functions
enabled
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Charge
Rechargeable battery
Bright Light
Electrical
energy
Solar cell
(Converts light to
electrical power.)
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Some or all
functions
disabled
Dis-
charge
Battery charges in the light. Battery discharges in the dark.
• The actual level at which some functions are disabled depends on the watch model.
• Be sure to read “Power Supply” for important information you need to know
when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch’s Power Saving function
has turned off the display to conserve power.
• See “Power Saving Function” for more information.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of this
product or its malfunction.
About This Manual
• The operational procedures for Modules 4709 and 4713
are identical. All of the illustrations in this manual show
Module 4713.
• Most of the display examples in this manual show only
the digital display, without the analog hands.
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Module 4709
Module 4713
▲
Dual Time Mode
Alarm ModeStopwatch Mode
General Guide
• Press B to change from mode to mode.
• In any mode (except when a setting screen is on the display), press A to illuminate
the display.
• When setting the time, you can also configure settings for the language of the day of
the week indicator (English or Japanese).
Press B.
Battery Level Indicator
▲
▲
▲
Hand Setting Mode
▲
Last signal screen
Timekeeping Mode
▲
▲
Radio-controlled Atomic Timekeeping
This watch receives a time calibration signal and updates
its time setting accordingly.
• Supported time calibration signals: Germany
(Mainflingen), England (Anthorn), United States (Fort
Collins), Japan.
Current Time Setting
This watch adjusts its time setting automatically in
accordance with a time calibration signal. You can also
perform a manual procedure to set the time and date,
when necessary.
• The first thing you should do after purchasing this watch
is to specify your Home Time Zone, which is the time
zone where you normally will use the watch. For more
information, see “To specify your Home Time Zone”.
Day of week
Seconds
Date
• When using the watch outside the areas covered by the time signal transmitters, you
will have to adjust the current time setting manually as required. See “Timekeeping”
for more information about manual time settings.
• The U.S. time calibration signal can be picked up by the watch while in North
America. The term “North America” in this manual refers to the area that consists of
Canada, the continental United States, and Mexico.
• The analog time of this watch is synchronized with the digital time. Because of this,
the analog time setting is automatically adjusted whenever you change the digital
setting. See “Analog Timekeeping” for more information.
To specify your Home Time Zone
1. In the Timekeeping Mode, hold down A the UTC
differential value starts to flash, which indicates the
setting screen.
• Though illumination will also turn on when you press
A, keep the button held down until UTC differential
value flashes.
2. Press C to select the time zone you want to use as
your Home Time Zone.
• Time calibration signal reception is supported when
any one of the time zones shown in the table below is
selected as your Time Zone.
Time zone
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
U.S. Signal
UTC differential value
UTC –10
UTC –9
UTC –8
UTC –7
UTC –6
UTC –5
Japan Signal
UTC differential value
UTC +8
UTC +9
German/U.K. Signal
UTC differential value
UTC +0
UTC +1
UTC +2
3. Press A to exit the setting screen.
Important!
• Normally, your watch should show the correct time as soon as you select your Home
Time Zone. If it does not, it should adjust automatically after the next auto receive
operation (in the middle of the night). You can also perform manual receive or you
can set the time manually.
• The watch will receive the time calibration signal automatically from the applicable
transmitter (in the middle of the night) and update its settings accordingly. For
information about the relationship between time zones and transmitters, see “Home
Time Zones and Transmitters”.
• Under factory default settings, auto receive is turned off for all of the following time
zones : UTC +8, UTC –10, and UTC –9. For details about turning on auto receive for
these time zones, see “To turn auto receive on and off”.
• You can disable time signal reception, if you want. See “To turn auto receive on and
off” for more information.
• See the maps under “Approximate Reception Ranges” for information about the
reception ranges of the watch.
• If you are in an area that does not use Daylight Saving Time (summer time), turn off
the DST setting.
Time Calibration Signal Reception
There are two different methods you can use to receive the time calibration signal:
auto receive and manual receive.
• Auto Receive
With auto receive, the watch receives the time calibration signal automatically up to
six times a day. When any auto receive is successful, the remaining auto receive
operations are not performed. For more information, see “About Auto Receive”.
• Manual Receive
Manual receive lets you start a time calibration receive operation with the press of a
button. For more information, see “To perform manual receive”.
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

casio-4713

Suche zurücksetzen

  • Die Zeitanzeige LCD ist korrekt, der mechanische Zeiger ist falsch
    Eingereicht am 22-7-2023 15:33

    Antworten Frage melden

  • Zeitzone 1 lässt sich bei Casio 4713 nicht einstellen. Eingereicht am 30-10-2022 06:54

    Antworten Frage melden

  • Die Zeitzone 1 lässt sich bei Casio 4713 nicht einstellen. Eingereicht am 30-10-2022 06:52

    Antworten Frage melden

  • Wie kann man die Sekunden von 48 Sekunden auf 00 Stellen



    Ich hab Eingereicht am 13-2-2022 14:50

    Antworten Frage melden

  • meine funk solar herrenarmbanduhr von casio, modul 4713 hat sich bei der zeitumstellung im märz 2019 nicht selbstständig umgestellt. was ist zu tun? Eingereicht am 7-4-2019 15:54

    Antworten Frage melden

  • Korrektur der Analogzeit nicht mehr möglich, kein Kontakt bei Mod-B-Taste. Eingereicht am 21-10-2018 11:10

    Antworten Frage melden

  • Mod Knopf B hat keinen Kontakt mehr . Korrektur der Analogzeit / Zeiger nicht möglich . Eingereicht am 21-10-2018 10:59

    Antworten Frage melden

  • wie kann ich Analogzeit einstellen (nu die Zeiger zeigen) ? Eingereicht am 10-10-2018 13:45

    Antworten Frage melden

  • Die Zeitanzeige mit Datum und Uhrzeit läuft richtig
    Der Minutenzeiger ist 15min. zu späht
    Wie kann ich den Zeiger wieder auf die Angezeigte Uhrzeit wieder einstellen Eingereicht am 2-1-2018 16:20

    Antworten Frage melden

  • Manuelle Funkübertragung wird abgebrochen. Es erscheint die Meldung ERR Eingereicht am 7-11-2017 09:56

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Casio 4713 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Casio 4713

Casio 4713 Bedienungsanleitung - Deutsch - 6 seiten

Casio 4713 Bedienungsanleitung - Holländisch - 6 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info