624486

Casio 5443 Seite 9

9
Zoom out
Zoom in
Vorherige Seite
1/10
Nächste Seite
E-64
Auto light precautions
• Illumination may not turn on if the face of the watch is more than 15 degrees above
or below parallel. Make sure that the back of your hand is parallel to the ground.
• Illumination turns off after the preset illumination duration (page E-61), even if you
keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with proper operation of auto light.
If illumination does not turn on, try moving the watch back to the starting position
(parallel with the ground) and then tilt it back towards your face again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of auto light, and
does not indicate a problem with the watch.
E-65
Button Operation Tone
When enabled, the button operation tone sounds any time you press one of the watch’s buttons. You can
enable or disable the button operation tone as desired.
• Even if you disable the button operation tone, the alarm, Hourly Time Signal, and Countdown Timer
Mode alarm all operate normally.
To enable or disable the button operation tone
1. In the Timekeeping Mode, hold down
A
until
ADJ
appears on the display.
• When you release
A
(after ADJ appears), the second hand will be pointing at the currently
selected city code.
2. Use
D
to cycle through settings on the display until the current button
operation tone setting (
MUTE
or
KEY
) is shown.
• See the sequence in step 2 of the procedure under “To change the
current time and date settings” (page E-17) for information about
how to scroll through setting screens.
3. Press
E
to toggle the button operation tone setting between enabled (
KEY
) and disabled (
MUTE
).
4. After the setting is the way you want, press
A
to exit the setting screen.
E-66
Low Battery Indication
A low battery indicator appears on the display when the power of the batteries is low. Have the batteries
replaced as soon as possible.
Note
• For guidelines covering the life of the batteries and supported battery types, see “Specifi cations”
(page E-72).
The conditions below are in effect while the low battery indicator is fl ashing.
• All hands are stopped.
• Except for the low battery indicator, all other display functions are
disabled.
• Watch tones are disabled.
• Display illumination is disabled.
• Watch operations are disabled.
Note
• Sequentially or repeatedly performing sensor, light, alarm, and other power intensive operations
over a short period can cause a sudden drop in battery power, which will make the low battery
indicator fl ash. Even though the low battery indicator may disappear and watch functions may
become re-enabled, battery replacement is recommended.
Low battery indicatorLow battery indicator
E-67
Troubleshooting
Time Setting
■
The current time setting is off by a couple of hours.
Your Home City setting may be wrong (page E-15). Check your Home City setting and correct it, if
necessary.
■
The current time setting is off by one hour.
You may need to change your Home City’s standard time/daylight saving time (DST) setting. Use the
procedure under “To change the current time and date settings” (page E-17).
World Time Mode
■
The time for my World Time City is off in the World Time Mode.
This could be due to incorrect switching between standard time and daylight saving time.
See “To confi gure World Time City and summer time settings” (page E-52) for more information.
E-68
Batteries
■
The low battery indicator is fl ashing on the digital display.
The watch’s battery power is low. Have the batteries replaced as soon as
possible.
See “Low Battery Indication” (page E-66).
Low battery indicatorLow battery indicator
E-69
Direction and Temperature Readings
■
The temperature unit setting won’t change.
The temperature unit setting is always Celsius (
°C
) whenever
TOKYO
is selected as the Home City. In
this case, the setting cannot be changed.
■
“ERR” appears while a sensor operation is in progress.
Subjecting the watch to strong impact can cause sensor malfunction or improper contact of internal
circuitry. When this happens,
ERR
(error) will appear on the display and sensor operations will be
disabled.
Digital Compass
Operation
Temperature
Measurement
•
If
ERR
appears while a measurement operation is being performed in a sensor mode, restart the
measurement. If
ERR
appears on the display again, it can mean there is something wrong with the
sensor.
• If
ERR
keeps appearing during measurement, it could mean there is a problem with the applicable
sensor.
E-70
Direction Readings
■
Abnormal magnetism detection is indicated.
• Move away from any potential source of strong magnetism and try
taking a reading again.
• If abnormal magnetism is detected again when you retry, it could mean
that the watch itself has become magnetized. If this happens, continue
to keep away from the source of strong magnetism, perform
bidirectional calibration, and then try taking a reading again. For more
information, refer to “To perform bidirectional calibration” (page E-26)
and “Location” (page E-32).
■
“ERR” appears on the display following bidirectional calibration.
If
- -
appears and then changes to
ERR
(error) on the calibration screen, it means that there is something
wrong with the sensor.
• If
ERR
disappears after about one second, try performing the calibration again.
• If
ERR
keeps appearing, contact your original dealer or nearest authorized CASIO distributor to have
the watch checked.
Whenever you have a sensor malfunction, take the watch to your original dealer or nearest authorized
CASIO distributor as soon as possible.
E-71
■
Incorrect direction readings.
• Incorrect bidirectional calibration. Perform bidirectional calibration (page E-26).
• Nearby source of strong magnetism, such as a household appliance, a large steel bridge, a steel
beam, overhead wires, etc., or an attempt to perform direction measurement on a train, boat, etc. Move
away from large metal objects and try again.
■
Different results produced by direction readings taken at the same location.
Magnetism generated by nearby high-tension wires is interfering with detection of terrestrial magnetism.
Move away from the high-tension wires and try again.
■
Problems taking direction readings indoors.
A TV, personal computer, speakers, or some other object is interfering with terrestrial magnetism
readings. Move away from the object causing the interference or take the direction reading outdoors.
Indoor direction readings are particularly diffi cult inside ferro-concrete structures.
Remember that you will not be able to take direction readings inside of trains, airplanes, etc.
Operation Guide 5442 5443
… 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Casio 5443 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Casio 5443

Casio 5443 Bedienungsanleitung - Deutsch - 10 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info