216226
37
Zoom out
Zoom in
Vorherige Seite
1/40
Nächste Seite
E-37
Troubleshooting
English
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Red steady
:–
The projector was turned off automatically due to some
problem that was probably caused by external digital noise or
some other reason. Confirm that the POWER/STANDBY
indicator is lit red (without flashing). After checking the
POWER/STANDBY indicator, disconnect the power cord from
the projector and wait for all of the projector’s indicators to go
out. Next, reconnect the power cord and turn projector power
back on.
If the error occurs again when you turn power back on,
contact your retailer or nearest authorized CASIO Service
Center.
Message :
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Red flashing
(0.5-second interval)
: Red flashing
(0.5-second interval)
The projector was turned off automatically because the lamp
turned off or did not turn on. After confirming that the
POWER/STANDBY indicator is lit red (without flashing), unplug
the power cord. Wait for a short while and then plug it back
in and turn on the projector again.
If the error occurs again when you turn power back on, wait
until the projector cools down and then replace the lamp
(page E-29).
If the lamp does not light after you replace it, contact your
retailer or nearest authorized CASIO Service Center.
Message :
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Red flashing
(2-second interval)
: Not lit or red flashing
Power has turned off automatically due to a projector memory
error. Confirm that the POWER/STANDBY indicator is lit red
(without flashing). After checking the POWER/STANDBY
indicator, disconnect the power cord from the projector and
wait for all of the projector’s indicators to go out. Next,
reconnect the power cord and turn projector power back on.
If the error occurs again when you turn power back on,
contact your retailer or nearest authorized CASIO Service
Center.
Message :
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Amber flashing
(1-second interval)
:–
Power has turned off automatically because the lamp cover is
open. Perform the following steps.
1 After confirming that the POWER/STANDBY indicator is lit
red (without flashing), disconnect the power cord from the
projector.
2 Check to make sure that the lamp cover is closed.
3 Plug the power cord back in and turn the projector back
on again.
If the error occurs again when you turn power back on,
contact your retailer or nearest authorized CASIO Service
Center.
Message :
POWER
TEMP
LAMP
: Green steady
:–
: Red flashing
(1-second interval)
It is time to replace the lamp. Replace the lamp following the
steps under Replacing the Lamp” (page E-29). Press the
[ESC] key to clear the warning message.
Message : It is time to replace
the lamp. Use the
procedure in the
User’s Guide to
replace the lamp as
soon as possible.
Indicator/Error Message Description and Required Action
37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Casio xj s58 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info