Bedienungsanleitung Cateye CC-COM10W (Seite 3 von 3) (Englisch)

471825

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

COIN

Standard parts

Optional parts

How to restart

After changing the battery, or when the computer displays an error, restart the computer

according to the following procedure.

With the restarting operation, the speed unit, date, tire size, and record data in the data view are retained.*

When the restarting operation is performed before 0:00 in the morning, the trip distance and the Car-*

bon offset for the day are not saved due to the data view’s update timing. To retain the measurement

data for the day, perform the restarting operation before starting measurement on the next day.

Refer to “Data view’s update timing” for the procedure to save the data view.

Press the 1. AC button on the back of the computer.

Set the date. To set the date, refer to “Preparing the computer-3”.2.

At the time of setting the date, the latest record date in the data view is initially displayed, and any *

date before that cannot be set.

Set the clock. Refer to “Preparing the computer 4”.3.

Maintenance

To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and

wipe it off with a dry cloth.

Replacing the battery

Computer

If turns on, replace the battery. Install a new lithium battery

(CR2032) with the (+) side facing upward. After the battery change,

go through the restart operation, by pressing the AC button.

Then restart the computer according to “How to restart”.*

Sensor

When the speed is not displayed even after adjusting cor-

rectly, replace the battery. Install a new lithium battery

(CR2032) with the (+) side facing upward. After replacement,

check the positions of the sensor and magnet.

Troubleshooting

MODE does not work when the computer is mounted on its bracket.

Check that there is no dirt between the bracket and the computer.

Wash off the bracket with water to get rid of any dirt.

The sensor signal reception icon does not ﬂash (the speed is not displayed). (Move the com-

puter near the sensor, and turn the front wheel. If the sensor signal reception icon ﬂashes, this

trouble may be a matter of transmission distance due to battery drain, but not any malfunction.)

Check that the clearance between the sensor and magnet is not too large. (Clearance: within 5 mm)

Check that the magnet passes through the sensor zone correctly.

Adjust the positions of the magnet and sensor.

Is the computer installed at the correct angle?

Back of computer must face toward the sensor.

Check that the distance between the computer and sensor is correct. (Distance: within 20 to 70 cm)

Install the sensor within the speciﬁed range.

Is the computer or sensor battery weak?

In winter, battery performance diminishes.

Replace with new batteries. After replacement, follow the procedure “Replacing the battery”.

No display.

Is battery in the computer run down?

Replace it. Then restart the computer referring to “How to restart”.

Incorrect data appear.

Restart the computer referring to “How to restart”.

COIN

Speciﬁcation

Battery

Computer : Lithium battery (CR2032) x 1, Sensor : Lithium battery (CR2032) x 1

Battery life Computer :

Approx. 1 years (If the computer is used for 1 hour/day; the battery life will vary

depending on the conditions of use.)

Sensor : Unit Total Distance reaches about 10000 km (6250 mile)

It may be shortened signiﬁcantly when backlight is used frequently.*

This is the average ﬁgure of being used under 20 °C temperature and the distance between the *

computer and the sensor is 65 cm.

Controller ..........................4 bit, 1-chip microcomputer (Crystal controlled oscillator)

Display ..............................Liquid crystal display

Sensor ..............................No contact magnetic sensor

Transmission distance ......Between 20 and 70 cm

Tire circumference range

......

0100 mm - 3999 mm (Initial value: 2096 mm)

Working temperature ........32 °F - 104 °F (0 °C - 40 °C) (This product will not display appropriately when

exceeding the Working Temperature range. Slow response or black LCD at lower or

higher temperature may happen respectively.)

Dimensions/weight

Computer : 2-9/32” x 1-1/2” x 3/4” (58 x 38 x 19 mm) / 1.02 oz (29 g)

Sensor : 1-41/64” x 1-3/8” x 19/32” (41.5 x 35 x 15 mm) / 0.53 oz (15 g)

The factory-loaded battery life might be shorter than the above-mentioned speciﬁcation.*

The speciﬁcations and design are subject to change without notice.*

CR2032

Open

CR2032

#160-2190N

Parts kit

#160-2196

Speed sensor

#160-0280N

Bracket band

#166-5150

Lithium battery (CR2032)

#169-9691N

Wheel

magnet

#160-2193

Bracket

#160-2770

Bracket holder

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye CC-COM10W Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye CC-COM10W

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info