Bedienungsanleitung Cateye CC-GL50 (Seite 40 von 41) (Englisch)

538691

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

Introduction

How to install the

unit on your bicycle

Setting up the

computer

How to use the

computer

Setup of your PC

Uploading the

measurement data

Changing the

computer

conﬁguration

Others

How to install the heart rate sensor (HR-11)

Heart rate is measured when the heart rate sensor is worn on the chest.

Warning!!! : This product must NOT be used by those who have a pacemaker.

• To avoid measurement errors, it is recommended to moisten the electrode pads with water.

• If your skin is sensitive, the electrode pad may be moistened with water and worn on a thin

undershirt.

• Chest hair may interfere with the measurement.

Attach the heart rate sensor to the HR strap.

Push it in until it clicks.

Insert the HR strap hook to the other end of the strap.

Wear the heart rate sensor with the HR strap, and adjust the length of the HR strap to ﬁt

your chest size (under bust). Fastening the strap too tightly may cause discomfort.

* Wear the heart rate sensor so that the top of the sensor faces up.

* Ensure that the electrode pad is in direct contact with the

body.

* When your skin is dry, or wearing the heart rate sensor on

top of your undershirt may produce measurement errors.

To avoid errors, moisten the electrode pad.

Watch video

(YouTube)

Click the button, then a browser will open and a

video will be played back.

Temporarily secure the magnet

Temporarily secure the cadence magnet inside the crank

with nylon ties, so that it faces the sensor zone on the

CADENCE side.

Turn the sensor arm, and temporarily secure the wheel

magnet to the spoke that faces the sensor zone on the

SPEED side.

* When the speed sensor is not positioned appropriately in respect

to the two magnets (of

CADENCE

and

SPEED

), move the speed

sensor back and forth so that it is positioned properly. After you

move the speed sensor, adjust the position so that the two mag-

nets face the relevant sensor zone.

Adjust the distance to the magnet

Tilt the speed sensor so that the distance be-

tween the cadence magnet and the CADENCE

side of the speed sensor is about 3 mm, and

ﬁrmly secure it with the nylon ties.

Turn and adjust the sensor arm so that the

distance between the wheel magnet and the

sensor arm is about 3 mm, and ﬁrmly tighten

the sensor screw.

Securing various parts

Firmly tighten the nylon ties, sensor screw and magnet of

the speed sensor, and check for any loosening.

* For steel axle pedals, the cadence magnet can be magneti-

cally secured on the pedal axle. Make sure to remove the

double-sided tape from the magnet when doing this.

3 mm

Cadence

magnet

Speed sensor

CADENCE side

Wheel mag-

net

Heart rate sensor

HR strap

Hook

Back

Electrode pad

Cut extra length of the

nylon tie with scissors.

Sensor arm SPEED side

Sensor

screw

Cadence

magnet

Wheel magnet

Sensor zone

Nylon ties

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cateye CC-GL50 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye CC-GL50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info