Standard parts Optional parts
#160-2090N
Parts kit
#160-0280N
Braket band
#160-2093
Braket/Sensor
#160-2770
Bracket holder
#169-6180
Lithium battery
(CR1620)
#169-9691N
Wheel magnet
#169-9766
Cadence magnet
LIMITED WARRANTY
2-Year Computer only
(Accessories/Bracket sensor and Battery Consumption excluded)
CatEye cycle computers are warranted to be free of defects from materials and workmanship for a period of two years
from original purchase. If the product fails to work due to normal use, CatEye will repair or replace the defect at no
charge. Service must be performed by CatEye or an authorized retailer.
To return the product, pack it carefully and enclose the warranty certificate (proof or purchase) with instruction for
repair. Please write or type your name and address clearly on the warranty certificate.
Insurance, handling and transportation charges to CatEye shall be borne by person desiring service.
For UK and REPUBLIC OF IRELAND consumers, please return to the place of purchase. This does not affect your statutory
rights.
CO
.,
2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan
Attn: CATEYE Customer Service
Phone : (06)6719-6863
Fax : (06)6719-6033
E-mail : support@cateye.co.jp
URL : http://www
[For US Customers]
CA
2825 Wilderness Place Suite 1200, Boulder CO80301-5494 USA
Phone : 303.443.4595
T
Fax : 303.473.0006
E-mail : service@cateye.com
CC-RD200
Wheel selection ..... Toggle between the specified wheel size (tire circumference)
and . Use this function if the computer is to be shared
between two bicycles.
Pressing MODE toggles between
and .
Wheel size entry .... Pressing MODE increases the value, and pressing and
holding MODE moves to the next digit.
* To enter the wheel size
, display using “Wheel selection ”.
Clock setting .......... To set the clock, refer to “ Preparing the computer-4 ” .
Total distance manual entry
................................ Before reinitializing the computer, note the total distance. This
reading will later allow you to enter the total distance
manually. Pressing MODE increases the value, and pressing
and holding MODE moves to the next digit.
Speed unit .............. Pressing MODE toggles between
and .
Maintenance
To clean the computer or accessories, use diluted neutral detergent on a soft cloth,
and wipe it off with a dry cloth.
Replacing the battery
If the display appears faded, replace the battery.
Install a new lithium battery (CR1620) with the (+)
side facing upward. Then reinitialize the computer
referring to “ Preparing the computer”.
Speed
The contacts to be short-
circuited intermittently are
located on the back.
Troubleshooting
MODE does not work when the computer is mounted on its bracket.
Check that there is no dirt between the bracket and the computer
Wash off the bracket with water to get rid of any dir
Speed (Cadence) are not displayed. (T
the computer several times to create a short circuit while observing the display
numeric value appears, this signifies that the computer is functioning nor
Is the clearance between the sensor and magnet too great? (must be
≤
3 mm)
Does the magnet pass through the sensor line?
Adjust the positions of the magnet and sensor
Is there any foreign matter (which would prevent a clean contact) on the contact points of the computer and/or
bracket?
Clean the contact points.
Check that no wire cable is worn or broken. Even with a normal appearance, it may be that a wire cable could be
broken internally
Replace the bracket sensor set.
No display
Is battery in the computer run down?
Replace it. Then reinitialize the computer referring to “ Preparing the computer”.
Incorrect data appear
Reinitialize the computer referring to “ Preparing the computer”.
Specification
Bat ...................................... Lithium battery (CR1620) x 1
Battery life ................................ Approx. 2 years (Using the battery one hour a day; the battery life will var
conditions of use.)
Controller .................................. 4-bite, 1-chip microcomputer (Crystal controlled oscillator)
Display ...................................... Li quid crystal display
Sen ...................................... Ncontact magnetic sensor
Wheel circumference range ..... 0100 mm - 3999 mm (Default figure A: 2096 mm, B: 2096 mm)
Working temperature ............... 32 °F - 104 °F (0 °C - 40 °C) (This product will not display appropriately when exceeding the
Working T
may happen respectively
Dimensions/weight ................... 1-5 3/64” x 1-7/32 ” x 19/32” (46.5 x 31 x 15 mm) / 0.63 oz (18 g)
* The factory-loaded battery life might be shorter than the above-mentioned specification.
* The specifications and design are subject to change without notice.
C
O
IN
C
O
IN
CR1620
Close
Open
Cadence
MODE
MODE
MODE
MODEMODE
MODEMODE
MODEMODE
MODE
MODE
MENUMENU
MODEMODE
Starting/Stopping measurement
Measurements occur automatically
when the bicycle is in use. During
measurement,
or flashes.
Switching computer function
Pressing MODE switches function,
in order, as shown on the left.
Resetting data
To reset measurement data, display
any data other than for Dst-2 and then
press and hold MODE . Pressing and
holding MODE with Ds displayed
resets Dst only.
The total distance is never reset.
Power-saving function
If the computer has not received
any signal for an hour, power-
saving mode will activate and only
the clock will be displayed.
Alternatively, if the sensor detects a
signal or MODE is pressed, the main
display reappears.
Pace arrow
Indicates whether the current
speed is faster ( ) or slower ( )
than the average speed.
Operating the computer [Measuring screen]
Tm Elapsed Time
0:00’ 00” - 9:59 ’ 59”
C Cadence
0(20) - 299 rpm
Dst T
0.00 - 999.99 km [mile]
Dst
2
T
0.00 - 999.99 /
1000.0 - 9999.9 km [mile]
Av Average Speed
*2
0.0 - 200.0 km/h
[0.0 - 125.0 mph]
Mx Maximum Speed
0.0(4.0) - 200.0 km/h
[0.0(3.0) - 125.0 mph]
Odo T
0.0 - 9999.9 /
10000 - 99999 km [mile]
Clock
0:00 - 23:59
or 1:00 - 12:59
*1 With the computer installed on the bracket,
press on the three raised dots on the face of
the computer.
*2 If Tm exceeds approximately 27 hours or
DST exceeds 999.99 km, .E (Error) is
displayed as the average speed. Reset data.
Changing the computer settings [menu screen]
To bring up the menu screen, press MENU in any modeEach time MODE is
pressed, the relevant menu screen appears. Pressing and holding MODE
changes the setting of the displayed menu.
Current speed
0.0(4.0) - 200.0 km
[0.0(3.0) - 125.0 mph]
Selected Mode
*1
Wheel
selection
Wheel size entry Clock setting T
manual entry
Speed unit
* After changing, be sure to press MENU to register the setting.
* If the menu screen is not touched for a minute, the Measuring
screen reappears without data changes.
Setting
change (by
pressing &
holding)
