Bedienungsanleitung Cateye CC-RD300W (Seite 1 von 2) (Englisch)

471827

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Tire circumference

reference table

12 x 1.75

14 x 1.50

14 x 1.75

16 x 1.50

16 x 1.75

18 x 1.50

18 x 1.75

20 x 1.75

20 x 1-3/8

22 x 1-3/8

22 x 1-1/2

24 x 1

24 x 3/4

Tubular

24 x 1-1/8

24 x 1-1/4

24 x 1.75

24 x 2.00

24 x 2.125

26 x 7/8

26 x 1

(

)

26 x 1

(

)

26 x 1.25

26 x 1-1/8

26 x 1-3/8

26 x 1-1/2

26 x 1.40

26 x 1.50

26 x 1.75

26 x 1.95

26 x 2.00

26 x 2.10

26 x 2.125

26 x 2.35

26 x 3.00

27 x 1

27 x 1-1/8

27 x 1-1/4

27 x 1-3/8

650 x 20C

650 x 23C

650 x 35A

650 x 38A

650 x 38B

700 x 18C

700 x 19C

700 x 20C

700 x 23C

700 x 25C

700 x 28C

700 x 30C

700 x 32C

700C Tubular

700 x 35C

700 x 38C

700 x 40C

29 x 2.1

29 x 2.3

935

1020

1055

1185

1195

1340

1350

1515

1615

1770

1785

1753

1785

1795

1905

1890

1925

1965

1920

1913

1952

1953

1970

2068

2100

2005

2010

2023

2050

2055

2068

2070

2083

2170

2145

2155

2161

2169

1938

1944

2090

2125

2105

2070

2080

2086

2096

2105

2136

2146

2155

2130

2168

2180

2200

2288

2326

Tire size L (mm)

CATEYE STRADA WIRELESS

CYCLOCOMPUTER CC-RD300W

U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending

CCRD3W-110930 066600542 6

L mm

SEN

SOR

ZONE

5 mm

Install the sensor and magnet

Sensor zone

Inside of right front fork

Max

70 cm

YES! NO!

The distance between the computer

and the sensor must not exceed the

transmission range of 70 cm. The back

of the computer must face the sensor.

The magnet

must pass

through the

sensor zone.

The clearance

between the

sensor surface

and the magnet

must not

exceed 5 mm.

SENSOR

ZONE

SENSOR

ZONE

Click

For wing type handlebar or oversized

stem, bracket can be mounted using

the Bracket Holder and nylon ties.

(Option)

Caution:

Make sure that the back of the computer faces the sensor.

* The computer may not function appropriately on some

stem if its back does not face the sensor as shown in

When attaching the bracket to the stem

Spoke

Toward the

sensor zone

Install the magnet

While supporting it by hand,

Handlebar

Cut

Attach the bracket to the stem or handlebar

Remove/install the

computer

Caution:

Round off the cut edge

of the bracket band to

prevent injury.

Install the sensor

Inside of right front fork

* After installation, rotate the front wheel gently to check that the speed is displayed on the

computer. If the speed is not displayed, check that conditions

, and

, above, have

been done appropriately.

Stem

Pull

securely

* Install the sensor as close to the upper

part of the front fork as possible.

push it out as if lifting the front up

When attaching the bracket to the handlebar

How to install the unit on your bicycle

1 Bracket band

2 Bracket

Nut

4 Speed sensor

5 Magnet

6 Sensor rubber pad

7 Bracket rubber pad

8 Nylon ties (x2)

ENG

Before using the computer, please thoroughly read this manual and keep it for

future reference.

WARNING / CAUTION

• Do not concentrate on the computer while riding. Ride safely!

• Install the magnet, sensor, and bracket securely. Check these periodically.

• If a child swallows a battery, consult a doctor immediately.

• Do not leave the computer in direct sunlight for unnecessary or extended periods.

• Do not disassemble the computer.

• Do not drop the computer. Doing so may result in a computer malfunction or damage.

• When using the computer installed on the bracket, change the MODE by pressing on the three dots

below the screen. Pressing hard on other areas can result in malfunction or damage to the computer.

• Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the bracket

threads.

• When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol.

• Dispose of used batteries according to local regulations.

• LCD screen may be distorted when viewed through polarized sunglass lenses.

Wireless Sensor

The sensor was designed to receive signals within a maximum range of 70 cm, to reduce chance of

interference.

When adjusting the wireless sensor, note the following:

• Signals cannot be received if the distance between the sensor and the computer is too great.

• The transmission distance may be shorter due to low temperature or low battery.

• Signals can be received only when the back of the computer is facing the sensor.

Interference may occur, resulting in incorrect data, if the computer is:

• Near a TV, PC, radio, motor, or in a car or train.

• Close to a railroad crossing, railway tracks, TV stations and/or radar base.

• Using with other wireless devices in close proximity.

This device complies with Part 15 of the FCC Rules.Operation is subject to the following

two conditions:(1)This device may not cause harmful interference,and (2)this device

must accept any interference received,including interference that may cause undesired

operation.

Modifications The FCC requires the user to be notified that any changes or modifications

made to this device that are not expressly approved by CatEye Co.,Ltd.May void the user

’s authority to operate the equipment.

MODE

MENUMENU

MODEMODE

MODE

MENUMENU

MODEMODE

km/h ↔ mph

Increase

Move digits

(by pressing

& holding)

setting

the setting

Clear all data (initialization)

Press the AC button on the back.

Select the desired speed units

Select “ ” or “ ”.

Enter the tire circumference

Enter the tire circumference of your bicycle in mm.

* Refer to the tire circumference reference table.

Set the clock

When MODE is pressed and held, “Displayed

time”, “Hour”, and “Minute” will appear, in

this order.

24h ↔ 12h,

or increase

the value

Switch the

screen or

move digits

(by pressing

& holding)

Preparing the computer

Battery case cover

Push!

When the computer is

mounted on the bracket

: Speed unit

: Wheel size icon

: Sensor signal reception icon

Measure wheel circumference

(L) of your bike

To get the most accurate

calibration do a wheel roll out.

With the valve stem

perpendicular to the ground,

mark the pavement at the valve

stem. With the riders weight on

the bike, roll the wheel one tire

revolution in a straight line and

mark the ground when the

valve stem is perpendicular to

the ground again. Measure the

distance in millimeters. This is

the most accurate wheel

calibration number.

Cateye CC-RD300W Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cateye CC-RD300W

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info