508116
4
Zoom out
Zoom in
Vorherige Seite
1/23
Nächste Seite
ENG-7
ENG
ENG-6
S
P
E
E
D
C
A
D
E
N
C
E
SPEED
SPEED
CADENCE
2. Mount the speed sensor and magnet
2-1. Temporarily secure the speed sensor
Locate the speed sensor on the left chain stay as shown
above, and loosely secure it with the nylon ties.
* Do not tighten the nylon ties completely at this stage.
Once a nylon tie is tightened, it cannot be pulled out.
2-2. Mount the magnet
1. Loosen the setscrews both on the SPEED side
and CADENCE side of the speed sensor, and turn
the sensor to the angle as shown on the right.
2. Temporarily secure the wheel magnet to the
spoke so that it faces the sensor zone on the
SPEED side.
3. Temporarily secure the cadence magnet inside
the crank with nylon ties, so that it faces the
sensor zone on the CADENCE side.
* When the speed sensor is not positioned ap-
propriately in respect to the two magnets (in both
Steps 2 and 3), move the speed sensor back
and forth so that it is positioned properly.
After you move the speed sensor, adjust the
position so that the two magnets face the rel-
evant sensor zone.
4. After adjustment, tighten the nylon ties firmly
to secure the speed sensor.
Wheel magnet
Cadence magnet
Speed sensor
Nylon ties
Speed sensor
Wheel
magnet
Cadence
magnet
Nylon ties
Setscrew on the
CADENCE side
Sensor zone
Sensor
zone
Setscrew on the
SPEED side
Continue
How to install the unit on your bicycle
When attaching the Flex Tight ™ bracket to the stem
* Attach the bracket with its open end facing to the right.
When attaching the Flex Tight ™ bracket to the handlebar
* Attach the bracket with its open end facing to the right.
Cut extra length of the band with scissors.
Caution:
Round off the cut edge of the bracket band to
prevent injury.
Bracket
Bracket band
Bracket rubber pad
Stem
Bracket
Bracket band
Bracket rubber pad
Handlebar
1. Attach the bracket to the stem or handlebar
The Flex Tight bracket can be attached to either the stem or the handlebar depend-
ing on how the bracket and band are configured.
Caution:
Tighten the dial on the bracket band by hand only.
Over-tightening can damage the screw threads.
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Cateye V3 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Cateye V3

Cateye V3 Bedienungsanleitung - Deutsch - 23 seiten

Cateye V3 Bedienungsanleitung - Holländisch - 23 seiten

Cateye V3 Bedienungsanleitung - Französisch - 23 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info