Bedienungsanleitung CAWI ElCom 7205 (Seite 2 von 7) (Englisch, Holländisch, Französisch)

622509

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

6. Monitoring the battery charge level, replacing the batteries

If the charge remaining in the batteries is insufficient, then the red and green LEDs will blink alternately 10 times after

the combination has been entered. This is to remind you to install two new 1.5 Volt AA (alkaline) cells in the next few

days.

Note: If you ignore the low-battery warning over a longer period of time, then you must be aware of the hazard that it will

be possible to open the lock and, as a consequence, the safe only after new batteries have been installed.

The battery compartment cover is located to the right of the keypad housing. Remove the Phillips screw and then slide

the battery compartment cover carefully off of the keypad housing in the direction indicated by the arrow. See Figure 1.

Remove the exhausted batteries and replace them with two new 1.5 volt AA (alkaline) batteries. The direction in which

the batteries are to be installed is shown inside the battery compartment cover. The programmed combination will be

retained during battery replacement.

7. Programming the electronic lock

Before you use your safe for the first time it is necessary, for security reasons, to enter your personal combination; the

factory combination must not be retained. The lock should be programmed only with the door open and with the

electronic lock released. Select your new six-digit combination before starting the easy programming sequence. Do not

use any personal data for this combination, such as birthdays or other information which could be derived from

knowledge about your person. Store your combination in a safe place so that only you have access to it.

7.1 Programming the master combination

Note: Program only with the door open and the electronic lock released. The green LED must not be lit.

Note:

We can assume no guarantee liability for malfunctions caused by erroneous reprogramming or application of undue

force or improper treatment nor in case of injury to property or assets which, for example, is due to a failure to close the

safe properly.

We recommend obtaining suitable insurance coverage to protect the contents of your safe. Your property insurance

sales agent can provide details.

8. Troubleshooting in case of malfunction

If it is not possible to open your safe in spite of having carried out the instructions above, then please contact the safe

manufacturer.

Function

Activate programming mode

Select programming mode

Confirm entry

Enter the previous six-digit

combination

Confirm entry

Enter the new six-digit combination

Confirm the entry

Verify the new combination by

repeating your entry

Confirm entry

Cancel

Operation,Button(s)

1 2 3 4 5 6

6 5 4 3 2 1

Response

OK = Green LED blinks twice

Invalid = Red LED lights for 3

seconds

Comments

Set for 1 - 2 - 3 - 4 - 5 - 6

at the factory

Important: Please check

to see that the lock

functions correctly with

the new master

combination before you

close the door to the

container

Problem

Red LED lights for about 3 seconds

after the combination is entered.

Electronic lock does not respond to

any keypad entries.

The red and green LEDs blink

alternately, ten times.

Possible cause

Invalid combination was entered.

The lock-out period was activated by

entering an invalid combination

several times in sequence.

Low battery charge

Red LED lights for about 3 seconds

after programming a new master

combination.

The new master combination was

improperly programmed. The old

combination is retained.

Remedy

Enter valid combination.

Repeat the programming of the new

combination as described in Item 7.1 of

the operating instructions.

See Item 4 in the operating instructions.

Change out the batteries. See Item 6 in

the operating instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

CAWI ElCom 7205 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von CAWI ElCom 7205

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info