Bedienungsanleitung Cecotec Conga Windroid 980 connected (Seite 7 von 15) (Englisch)

753590

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

980 CONNECTED 4544

ENGLISH ENGLISH

Fig. 15.

Stop:

When cleaning is over, the product returns to the place where cleaning started and beeps.

Remove the robot from the surface

Fig. 16.

Grab the handle and press Start/Pause for more than 5 seconds. Then, remove the product.

Turn the robot off

Fig. 17.

Move the switch button to the “O” position.

Remove the safety suction pad

Fig. 18.

Unplug the product from the power supply.

Fig. 19.

Note: when the product displays a red light and beeps, please check if the power adapter is

connected correctly. When the power adapter is correctly connected, the product will show

a blue light and will start operating. When the power adapter is connected correctly, and

the product still shows a red light, please use the direction buttons on the remote control to

operate the product and move it from its current position, until the blue light shows up, press

Start/Pause keys on the remote control for the product to operate properly.

4. CLEANING AND MAINTENANCE

When cleaning the mop cloth and the bottom parts of the product, please switch off the

product.

Clean mop cloth

Turn the robot over and remove the mop cloth, soak it in cool, clean water for 2 minutes.

Handwash with mild detergent and lay flat to dry. Let it dry completely before attaching it

again to the robot.

Do not use a wet mop cloth on the robot or it may slip on the window.

Washing the mop cloth regularly can extend its service life.

If the cloth becomes worn or no longer fits, replace it with a new one to achieve best cleaning

performance.

Fig. 20.

Fan cleaning

Turn the robot over and wipe any debris from the fan with a cloth to maintain suction.

Guide wheels cleaning

Turn the robot over and wipe the four side rollers with a cloth to maintain their effectiveness.

Edge Detection Sensors cleaning

Turn over the robot and wipe five edge detection sensors clean with a cloth to maintain their

effectiveness.

Fig. 21.

Squeegees cleaning

Turn over the robot and wipe five edge detection sensors clean with a cloth to maintain their

effectiveness.

Driving wheels cleaning

Before cleaning the wheels, move the power switch to the “-” position. Then wait 8 seconds

until it stops vacuuming and starts beeping. Then press the Start/Pause button key on the

remote control and start cleaning the driving wheels.

Fig. 22.

Press Start/Pause and Clean buttons on the remote control to check the driving wheels. If

there is any dust, press pause and clean the dust.

Fig. 23.

After cleaning, turn off the switch on of the bottom part to the “O” position.

Light status indicator

Blue light

flashing

The product can be placed on the glass.

Steady blue

light

Product suction is succesful. The robot remains attached to window and it

can start cleaning the window.

Red light

flashing

The robot stops suctioning so it can be removed from the window.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cecotec Conga Windroid 980 connected Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info