Bedienungsanleitung Celestron 47001 (Seite 2 von 15) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

791749

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

If the battery power becomes low on the Sensor, a low battery icon will appear on the LCD display

and if so change batteries to ensure a strong signal is being sent to the Receiver in order that the

Sensor will send accurate information to the Receiver.

Settings and Operation of the Receiver

y Indoor & Outdoor Temperature & Humidity – the indoor

temperature and humidity is shown on the 2nd section of the LCD

display and the outdoor temperature and humidity is shown on the

3rd section of the display. The humidity trend (indoor and outdoor)

will be displayed in a small box to the right of the temperature

display. You will see an icon of indoor humidity of various faces –

happy, sad, or in between depending on the readings of very dry to

very wet.

y Data displayed in “C” or “F” – push the “DOWN” button (when

in a normal mode) to change from “C” (Centigrade) or “F”

(Fahrenheit) for the display you desire.

y Clock & Calendar – Press the “TIME” button and hold down for a

couple of seconds to enter the setup mode. Use the “UP” or

“DOWN” buttons to make changes. Press the “TIME” after each

setting is correct. The settings in sequence will be:

year/month/date/weekday language/hour/minute/time difference/exit. The weekday language to

choose is available in German, English, Italian, French, Dutch, Spanish, and Danish. The clock

format can be 12 or 24 hour mode – use the “UP” button (in normal mode) to change the format that

you wish to use.

y Moon Phase – will automatically be seen near the

center of the last display and will be correct if the

calendar is set accurately.

y Max/Min Memory – in normal mode, press the button

“MAX/MIN” to see the minimum temperature and

humidity both indoors and out, press the button again

to see the maximum temperature and humidity both

indoors and out, press the button again to return to the

normal mode. Hold down the button for three seconds to erase the memory.

y Temperature Alert – you can set a range of outdoor temperature alerts (high and low). In normal

mode press the “ALERT” button once and it will display an icon that the alert is enabled (to the

right of the outdoor temperature) and press again and the icon will be removed to indicate the alert

is disabled. To set the maximum and minimum temperatures for the alert, hold the “ALERT”

button down for a few seconds and a icon (top part) will flash to tell you to set the maximum

temperature alert – use the “UP” and “DOWN” buttons to choose your alert temperature and push

the “ALERT” button to set and then push the button again the lower icon will flash and you will

set the minimum temperature alert. When the temperature outdoors reaches the alarm stage, the

icons will flash and make a sound and last 5 seconds and then repeat every minute until you press

any button to stop the alarm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron 47001 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info