Bedienungsanleitung Celestron NexStar EVOLUTION (Seite 7 von 15) (Englisch)

667018

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

I 1312 I

Note: You must tap “Done” in the upper right corner of your

screen for the setting changes to take effect.

Utilities

• Battery Status - Displays the battery voltage, whether it’s

discharging or charging, and High, Medium, or Low status.

• Tray Lighting - Adjusts the LED brightness of the accessory

tray light. Light can be turned off by sliding all the way to 0.

• Logo Lighting - Adjusts the LED brightness of the

Celestron power logo and the WiFi logo. Can be dimmed

down or shut off for dark sky locations.

Behavior

• Align Using SkyAlign - The default and recommended

alignment for the NexStar Evolution is SkyAlign. Alignment

is achieved by centering and aligning 3 bright stars in the

telescope’s eyepiece.

• Align Using Manual Align - Identify, select, and center

3 named stars in the telescope’s eyepiece. The star is

selected on your screen and centered with the on-screen

direction arrows.

• Hibernate Enabled - Allows the telescope alignment to

be saved when shutting the telescope off or disconnecting

and exiting the app.

• Max Slew Rate Enabled - Allows the max slew speed to

be adjusted from default.

• Max Slew Rate - Increasing speed will draw more battery

power. Decreasing speed will operate more quietly.

Tracking Rate

• Sidereal - Compensates for the rotation of the Earth to

keep objects centered in the eyepiece of your telescope.

This is the default tracking rate and used for all stars and

deep space objects.

• Lunar - Used for tracking the Moon and when observing

the lunar landscape.

• Solar - Used for tracking the Sun when solar observing

with a proper ﬁlter.

• Off - Turns tracking off. The motors in the telescope will

stop unless you are slewing.

Anti-Backlash

All mechanical gears have a certain amount of backlash or

play between the gears. This is seen as a delay in the time

it takes for the telescope to move after a direction arrow is

pressed, especially when changing directions. Anti-back-

lash compensates for backlash by inputting a value which

quickly rewinds the motors just enough to eliminate the play

between gears.

• Altitude - Sets the backlash compensation value for alti-

tude (up/down motion of the telescope), 0-99.

• Azimuth - Sets the backlash compensation value for azi-

muth (left/right motion of the telescope), 0-99.

Altitude Slew Limits

The NexStar Evolution used with 6”, 8”, and 9.25” optical

tubes will point straight overhead without obstruction. Using

oversized accessories like DSLRs and T-adapters may re-

quire limiting the altitude angle to prevent striking the mount.

Note that the slew limit does not work until the telescope is

aligned with the sky, or the slew limit assumes the telescope

is pointing horizontally.

• Maximum - Sets the maximum (or highest) limit, 0-90º.

Use to prevent the telescope from striking the mount when

oversized accessories are attached

• Minimum – Sets the minimum (or lowest) limit, 0-90º. This

setting is useful when trying to avoid obstructed horizons.

Slew Buttons at Slow Speeds

Telescope direction can be reversed up/down and left/right

to change the apparent motion of the star in the telescope’s

eyepiece in the three lowest slew speeds. Reverse Up and

Down is default enabled so the star moves in the same direc-

tion as the direction button.

• Reverse Left and Right - Reverses left and right direc-

tions in the three lowest slew speeds.

• Reverse Up and Down - Reverses up and down direc-

tions in three lowest slew speeds.

Advanced

Advanced settings in NexStar Evolution allow you to adjust

two power management features.

• External Power - Sets the maximum potential current

draw from the power supply. Default is 2.0A for the includ-

ed power supply. Any setting higher than 2.0 requires

a higher capacity power supply, which is not includ-

ed with the telescope. The telescope has built-in fail

safes if the External Power setting is incorrectly set, but we

recommend always using a suitable power supply for the

given setting.

When used with a higher capacity power supply, this setting

allows you to charge the internal battery at the fastest speed

while using the telescope, and while optionally charging your

smart device from the USB charger.

• USB Charger - Sets the USB charger on the mount to

always On or Auto. Default is Auto, meaning the charger

will shut off to save battery life when the battery is low. On

will force the charger to stay on at all times, even when the

battery is low.

Go To

Simply enter the Right Ascension (RA) and Declination (Dec)

coordinates to slew t0 a speciﬁed area of sky. This is the

quickest way to go to a custom object, such as a new comet

or object of intereste provided by a star chart or online reference.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Celestron NexStar EVOLUTION Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info